AMCC yosemite 440ep PCI slot doesn't work.

[Andrew Liu]

Currently, ppc44x use ppc branch, not powerpc, especially for AMCC
yosemite 440ep.

Through adding printk in function ppc4xx_pic_init which is in
arch/ppc/syslib/ppc4xx_pic.c, whether setting  IRQ_LEVEL has no effect
on it.



BRs,
Andrew


Valentine Barshak wrote:
> Stefan Roese wrote:
>> On Monday 24 September 2007, Andrew Liu wrote:
>>> By default, it is IRQ_SENSE_LEVEL | IRQ_POLARITY_NEGATIVE
>>
>> And that should be correct for PCI interrupts.
>>
>>>  I change it to IRQ_SENSE_EDGE | IRQ_POLARITY_NEGATIVE  or
>>> IRQ_SENSE_EDGE | IRQ_POLARITY_POSITIVE.
>>> It  displays:
>>> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
>>> eth2: no IPv6 routers present
>>> NETDEV WATCHDOG: eth2: transmit timed out
>>> eth2: Transmit timeout, status 0c 0005 c07f media 10.
>>> eth2: Tx queue start entry 4  dirty entry 0.
>>> eth2:  Tx descriptor 0 is 0008a05a. (queue head)
>>> eth2:  Tx descriptor 1 is 0008a04e.
>>> eth2:  Tx descriptor 2 is 0008a046.
>>> eth2:  Tx descriptor 3 is 0008a05a.
>>> eth2: link up, 100Mbps, full-duplex, lpa 0x45E1
>>>
>>> and
>>> root at localhost:/root> ifconfig  eth2
>>> eth2      Link encap:Ethernet  HWaddr 00:0E:2E:7E:F5:E6
>>>           inet addr:128.224.149.13  Bcast:128.224.255.255 
>>> Mask:255.255.0.0
>>>           inet6 addr: fe80::20e:2eff:fe7e:f5e6/64 Scope:Link
>>>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>>>           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>           collisions:0 txqueuelen:1000
>>>           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
>>>           Interrupt:25 Base address:0x6f00
>>>
>>>
>>> and
>>> root at localhost:/root> cat /proc/interrupts
>>>            CPU0
>>>   2:          0  UIC0 Edge      IBM IIC
>>>   7:          0  UIC0 Edge      IBM IIC
>>>  10:      11961  UIC0 Edge      MAL TX EOB
>>>  11:      18471  UIC0 Edge      MAL RX EOB
>>>  25:          0  UIC0 Edge      eth2
>>>  32:          0  UIC1 Edge      MAL SERR
>>>  33:          0  UIC1 Edge      MAL TX DE
>>>  34:          0  UIC1 Edge      MAL RX DE
>>>  40:         32  UIC1 Edge      ohci_hcd:usb1
>>>  60:          0  UIC1 Edge      EMAC
>>> BAD:          0
>>>
>>>
>>> Can PCI slot use level trigger?
>>>
>>> give me some advice.
>
> This could be caused by misseting the IRQ_lEVEL flag in desc->status.
> There have been a commit 4dc7b4b0405fd7320940849b6e31ea8ea68fd0df that
> fixes the problem.
> Thanks,
> Valentine.
>
>>
>> Hmmm. Did you try an earlier Linux version too? For example 2.6.22 or
>> even earlier? Please give it a try and let us know if the same
>> problem occurs.
>>
>> Best regards,
>> Stefan
>>
>> =====================================================================
>> DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
>> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
>> Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
>> =====================================================================
>
>