[PATCH] [v3] PPC 4xx: Enable XMON on PPC 4xx boards

[Josh Boyer]

The following patch allows XMON to run on the 4xx platform.  Tested on
Walnut, Ebony, and Nova (440GX based) eval boards.  440EP and 440SP boards
should work as well.  Patch is against 2.6.18-rc6.

Signed-off-by: Josh Boyer <jdub at us.ibm.com>

---
 arch/ppc/xmon/start.c |   21 +++++++++++++++++++++
 arch/ppc/xmon/xmon.c  |   26 ++++++++++++++++++++------
 2 files changed, 41 insertions(+), 6 deletions(-)

--- linux-2.6.orig/arch/ppc/xmon/xmon.c
+++ linux-2.6/arch/ppc/xmon/xmon.c
@@ -153,6 +153,12 @@ static int xmon_trace[NR_CPUS];
 #define SSTEP	1		/* stepping because of 's' command */
 #define BRSTEP	2		/* stepping over breakpoint */
 
+#ifdef CONFIG_4xx
+#define MSR_SSTEP_ENABLE 0x200
+#else
+#define MSR_SSTEP_ENABLE 0x400
+#endif
+
 static struct pt_regs *xmon_regs[NR_CPUS];
 
 extern inline void sync(void)
@@ -211,6 +217,14 @@ static void get_tb(unsigned *p)
 	p[1] = lo;
 }
 
+static inline void xmon_enable_sstep(struct pt_regs *regs)
+{
+	regs->msr |= MSR_SSTEP_ENABLE;
+#ifdef CONFIG_4xx
+	mtspr(SPRN_DBCR0, mfspr(SPRN_DBCR0) | DBCR0_IC | DBCR0_IDM);
+#endif
+}
+
 int xmon(struct pt_regs *excp)
 {
 	struct pt_regs regs;
@@ -254,10 +268,10 @@ int xmon(struct pt_regs *excp)
 	cmd = cmds(excp);
 	if (cmd == 's') {
 		xmon_trace[smp_processor_id()] = SSTEP;
-		excp->msr |= 0x400;
+		xmon_enable_sstep(excp);
 	} else if (at_breakpoint(excp->nip)) {
 		xmon_trace[smp_processor_id()] = BRSTEP;
-		excp->msr |= 0x400;
+		xmon_enable_sstep(excp);
 	} else {
 		xmon_trace[smp_processor_id()] = 0;
 		insert_bpts();
@@ -298,7 +312,7 @@ xmon_bpt(struct pt_regs *regs)
 		remove_bpts();
 		excprint(regs);
 		xmon_trace[smp_processor_id()] = BRSTEP;
-		regs->msr |= 0x400;
+		xmon_enable_sstep(regs);
 	} else {
 		xmon(regs);
 	}
@@ -385,7 +399,7 @@ insert_bpts(void)
 		}
 		store_inst((void *) bp->address);
 	}
-#if !defined(CONFIG_8xx)
+#if ! (defined(CONFIG_8xx) || defined(CONFIG_4xx))
 	if (dabr.enabled)
 		set_dabr(dabr.address);
 	if (iabr.enabled)
@@ -400,7 +414,7 @@ remove_bpts(void)
 	struct bpt *bp;
 	unsigned instr;
 
-#if !defined(CONFIG_8xx)
+#if ! (defined(CONFIG_8xx) || defined(CONFIG_4xx))
 	set_dabr(0);
 	set_iabr(0);
 #endif
@@ -677,7 +691,7 @@ bpt_cmds(void)
 
 	cmd = inchar();
 	switch (cmd) {
-#if !defined(CONFIG_8xx)
+#if ! (defined(CONFIG_8xx) || defined(CONFIG_4xx))
 	case 'd':
 		mode = 7;
 		cmd = inchar();
--- linux-2.6.orig/arch/ppc/xmon/start.c
+++ linux-2.6/arch/ppc/xmon/start.c
@@ -73,6 +73,27 @@ xmon_map_scc(void)
 	TXRDY = 0x20;
 	RXRDY = 1;
 	DLAB = 0x80;
+#elif defined(CONFIG_440EP)
+	sccd = (volatile unsigned char *) ioremap(0xef600300, 8);
+	sccc = sccd + 5;
+	TXRDY = 0x20;
+	RXRDY = 1;
+	DLAB = 0x80;
+#elif defined(CONFIG_440SP)
+	sccd = (volatile unsigned char *) ioremap64(0x00000001f0000200ULL, 8);
+	sccc = sccd + 5;
+	TXRDY = 0x20;
+	RXRDY = 1;
+	DLAB = 0x80;
+#elif defined(CONFIG_44x)
+	/* This is the default for 44x platforms.  Any boards that have a
+	   different UART address need to be put in cases before this or the
+	   port will be mapped incorrectly */
+	sccd = (volatile unsigned char *) ioremap64(0x0000000140000200ULL, 8);
+	sccc = sccd + 5;
+	TXRDY = 0x20;
+	RXRDY = 1;
+	DLAB = 0x80;
 #endif /* platform */
 
 	register_sysrq_key('x', &sysrq_xmon_op);