[PATCH] Fbdev driver for IBM GXT4500P video cards
Paul Mackerras
paulus at samba.org
Fri Nov 24 13:51:48 EST 2006
This is an fbdev driver for the IBM GXT4500P display card found in
some IBM System P (pSeries) machines. These cards have hardware 2D
and 3D capabilities, but the driver does not use them; it just exports
a dumb framebuffer.
Signed-off-by: Paul Mackerras <paulus at samba.org>
---
Antonino, if there are no adverse comments on this driver, I'd like it
to go in 2.6.20.
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 7a43020..8085040 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -1611,6 +1611,16 @@ config FB_PNX4008_DUM_RGB
---help---
Say Y here to enable support for PNX4008 RGB Framebuffer
+config FB_IBM_GXT4500
+ tristate "Framebuffer support for IBM GXT4500P adaptor"
+ depends on PPC
+ select FB_CFB_FILLRECT
+ select FB_CFB_COPYAREA
+ select FB_CFB_IMAGEBLIT
+ ---help---
+ Say Y here to enable support for the IBM GXT4500P display
+ adaptor, found on some IBM System P (pSeries) machines.
+
config FB_VIRTUAL
tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
depends on FB
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index a6980e9..309a26d 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -99,6 +99,7 @@ obj-$(CONFIG_FB_IMX) += imx
obj-$(CONFIG_FB_S3C2410) += s3c2410fb.o
obj-$(CONFIG_FB_PNX4008_DUM) += pnx4008/
obj-$(CONFIG_FB_PNX4008_DUM_RGB) += pnx4008/
+obj-$(CONFIG_FB_IBM_GXT4500) += gxt4500.o
# Platform or fallback drivers go here
obj-$(CONFIG_FB_VESA) += vesafb.o
diff --git a/drivers/video/gxt4500.c b/drivers/video/gxt4500.c
new file mode 100644
index 0000000..b39d4c5
--- /dev/null
+++ b/drivers/video/gxt4500.c
@@ -0,0 +1,681 @@
+/*
+ * Frame buffer device for IBM GXT4500P display adaptor
+ *
+ * Copyright (C) 2006 Paul Mackerras, IBM Corp. <paulus at samba.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/fb.h>
+#include <linux/console.h>
+#include <linux/pci.h>
+#include <linux/pci_ids.h>
+#include <linux/delay.h>
+
+#define PCI_DEVICE_ID_IBM_GXT4500P 0x21c
+
+/* GXT4500P registers */
+
+/* Registers in PCI config space */
+#define CFG_ENDIAN0 0x40
+
+/* Misc control/status registers */
+#define STATUS 0x1000
+#define CTRL_REG0 0x1004
+#define CR0_HALT_DMA 0x4
+#define CR0_RASTER_RESET 0x8
+#define CR0_GEOM_RESET 0x10
+#define CR0_MEM_CTRLER_RESET 0x20
+
+/* Framebuffer control registers */
+#define FB_AB_CTRL 0x1100
+#define FB_CD_CTRL 0x1104
+#define FB_WID_CTRL 0x1108
+#define FB_Z_CTRL 0x110c
+#define FB_VGA_CTRL 0x1110
+#define REFRESH_AB_CTRL 0x1114
+#define REFRESH_CD_CTRL 0x1118
+#define FB_OVL_CTRL 0x111c
+#define FB_CTRL_TYPE 0x80000000
+#define FB_CTRL_WIDTH_MASK 0x007f0000
+#define FB_CTRL_WIDTH_SHIFT 16
+#define FB_CTRL_START_SEG_MASK 0x00003fff
+
+#define REFRESH_START 0x1098
+#define REFRESH_SIZE 0x109c
+
+/* "Direct" framebuffer access registers */
+#define DFA_FB_A 0x11e0
+#define DFA_FB_B 0x11e4
+#define DFA_FB_C 0x11e8
+#define DFA_FB_D 0x11ec
+#define DFA_FB_ENABLE 0x80000000
+#define DFA_FB_BASE_MASK 0x03f00000
+#define DFA_FB_STRIDE_1k 0x00000000
+#define DFA_FB_STRIDE_2k 0x00000010
+#define DFA_FB_STRIDE_4k 0x00000020
+#define DFA_PIX_8BIT 0x00000000
+#define DFA_PIX_16BIT_565 0x00000001
+#define DFA_PIX_16BIT_1555 0x00000002
+#define DFA_PIX_24BIT 0x00000004
+#define DFA_PIX_32BIT 0x00000005
+
+/* maps DFA_PIX_* to pixel size in bytes */
+static unsigned char pixsize[] = {
+ 1, 2, 2, 2, 4, 4
+};
+
+/* Display timing generator registers */
+#define DTG_CONTROL 0x1900
+#define DTG_CTL_SCREEN_REFRESH 2
+#define DTG_CTL_ENABLE 1
+#define DTG_HORIZ_EXTENT 0x1904
+#define DTG_HORIZ_DISPLAY 0x1908
+#define DTG_HSYNC_START 0x190c
+#define DTG_HSYNC_END 0x1910
+#define DTG_HSYNC_END_COMP 0x1914
+#define DTG_VERT_EXTENT 0x1918
+#define DTG_VERT_DISPLAY 0x191c
+#define DTG_VSYNC_START 0x1920
+#define DTG_VSYNC_END 0x1924
+#define DTG_VERT_SHORT 0x1928
+
+/* PLL/RAMDAC registers */
+#define PLL_M 0x4040
+#define PLL_N 0x4044
+#define PLL_POSTDIV 0x4048
+
+/* Hardware cursor */
+#define CURSOR_X 0x4078
+#define CURSOR_Y 0x407c
+#define CURSOR_HOTSPOT 0x4080
+#define CURSOR_MODE 0x4084
+#define CURSOR_MODE_OFF 0
+#define CURSOR_MODE_4BPP 1
+#define CURSOR_PIXMAP 0x5000
+#define CURSOR_CMAP 0x7400
+
+/* Window attribute table */
+#define WAT_FMT 0x4100
+#define WAT_FMT_24BIT 0
+#define WAT_FMT_16BIT_565 1
+#define WAT_FMT_16BIT_1555 2
+#define WAT_FMT_32BIT 3 /* 0 vs. 3 is a guess */
+#define WAT_FMT_8BIT_332 9
+#define WAT_FMT_8BIT 0xa
+#define WAT_FMT_NO_CMAP 4 /* ORd in to other values */
+#define WAT_CMAP_OFFSET 0x4104 /* 4-bit value gets << 6 */
+#define WAT_CTRL 0x4108
+#define WAT_CTRL_SEL_B 1 /* select B buffer if 1 */
+#define WAT_CTRL_NO_INC 2
+#define WAT_GAMMA_CTRL 0x410c
+#define WAT_GAMMA_DISABLE 1 /* disables gamma cmap */
+#define WAT_OVL_CTRL 0x430c /* controls overlay */
+
+/* Indexed by DFA_PIX_* values */
+static unsigned char watfmt[] = {
+ WAT_FMT_8BIT, WAT_FMT_16BIT_565, WAT_FMT_16BIT_1555, 0,
+ WAT_FMT_24BIT, WAT_FMT_32BIT
+};
+
+/* Colormap array; 1k entries of 4 bytes each */
+#define CMAP 0x6000
+
+#define readreg(par, reg) readl((par)->regs + (reg))
+#define writereg(par, reg, val) writel((val), (par)->regs + (reg))
+
+struct gxt4500_par {
+ void __iomem *regs;
+
+ int pixfmt; /* pixel format, see DFA_PIX_* values */
+
+ /* PLL parameters */
+ int pll_m; /* ref clock divisor */
+ int pll_n; /* VCO divisor */
+ int pll_pd1; /* first post-divisor */
+ int pll_pd2; /* second post-divisor */
+
+ u32 pseudo_palette[16]; /* used in color blits */
+};
+
+/* mode requested by user */
+static char *mode_option;
+
+/* default mode: 1280x1024 @ 60 Hz, 8 bpp */
+static struct fb_videomode defaultmode __devinitdata = {
+ .refresh = 60,
+ .xres = 1280,
+ .yres = 1024,
+ .pixclock = 9295,
+ .left_margin = 248,
+ .right_margin = 48,
+ .upper_margin = 38,
+ .lower_margin = 1,
+ .hsync_len = 112,
+ .vsync_len = 3,
+ .vmode = FB_VMODE_NONINTERLACED
+};
+
+/*
+ * The refclk and VCO dividers appear to use linear feedback shift
+ * registers, which get reloaded when they reach a terminal value, at
+ * which point the divider output is toggled. Thus one can obtain
+ * whatever divisor is required by putting the appropriate value into
+ * the reload register. For a divisor of N, one puts the value from
+ * the LFSR sequence that comes N-1 places before the terminal value
+ * into the reload register.
+ */
+
+static unsigned char mdivtab[] = {
+/* 1 */ 0x3f, 0x00, 0x20, 0x10, 0x28, 0x14, 0x2a, 0x15, 0x0a,
+/* 10 */ 0x25, 0x32, 0x19, 0x0c, 0x26, 0x13, 0x09, 0x04, 0x22, 0x11,
+/* 20 */ 0x08, 0x24, 0x12, 0x29, 0x34, 0x1a, 0x2d, 0x36, 0x1b, 0x0d,
+/* 30 */ 0x06, 0x23, 0x31, 0x38, 0x1c, 0x2e, 0x17, 0x0b, 0x05, 0x02,
+/* 40 */ 0x21, 0x30, 0x18, 0x2c, 0x16, 0x2b, 0x35, 0x3a, 0x1d, 0x0e,
+/* 50 */ 0x27, 0x33, 0x39, 0x3c, 0x1e, 0x2f, 0x37, 0x3b, 0x3d, 0x3e,
+/* 60 */ 0x1f, 0x0f, 0x07, 0x03, 0x01,
+};
+
+static unsigned char ndivtab[] = {
+/* 2 */ 0x00, 0x80, 0xc0, 0xe0, 0xf0, 0x78, 0xbc, 0x5e,
+/* 10 */ 0x2f, 0x17, 0x0b, 0x85, 0xc2, 0xe1, 0x70, 0x38, 0x9c, 0x4e,
+/* 20 */ 0xa7, 0xd3, 0xe9, 0xf4, 0xfa, 0xfd, 0xfe, 0x7f, 0xbf, 0xdf,
+/* 30 */ 0xef, 0x77, 0x3b, 0x1d, 0x8e, 0xc7, 0xe3, 0x71, 0xb8, 0xdc,
+/* 40 */ 0x6e, 0xb7, 0x5b, 0x2d, 0x16, 0x8b, 0xc5, 0xe2, 0xf1, 0xf8,
+/* 50 */ 0xfc, 0x7e, 0x3f, 0x9f, 0xcf, 0x67, 0xb3, 0xd9, 0x6c, 0xb6,
+/* 60 */ 0xdb, 0x6d, 0x36, 0x9b, 0x4d, 0x26, 0x13, 0x89, 0xc4, 0x62,
+/* 70 */ 0xb1, 0xd8, 0xec, 0xf6, 0xfb, 0x7d, 0xbe, 0x5f, 0xaf, 0x57,
+/* 80 */ 0x2b, 0x95, 0x4a, 0x25, 0x92, 0x49, 0xa4, 0x52, 0x29, 0x94,
+/* 90 */ 0xca, 0x65, 0xb2, 0x59, 0x2c, 0x96, 0xcb, 0xe5, 0xf2, 0x79,
+/* 100 */ 0x3c, 0x1e, 0x0f, 0x07, 0x83, 0x41, 0x20, 0x90, 0x48, 0x24,
+/* 110 */ 0x12, 0x09, 0x84, 0x42, 0xa1, 0x50, 0x28, 0x14, 0x8a, 0x45,
+/* 120 */ 0xa2, 0xd1, 0xe8, 0x74, 0xba, 0xdd, 0xee, 0xf7, 0x7b, 0x3d,
+/* 130 */ 0x9e, 0x4f, 0x27, 0x93, 0xc9, 0xe4, 0x72, 0x39, 0x1c, 0x0e,
+/* 140 */ 0x87, 0xc3, 0x61, 0x30, 0x18, 0x8c, 0xc6, 0x63, 0x31, 0x98,
+/* 150 */ 0xcc, 0xe6, 0x73, 0xb9, 0x5c, 0x2e, 0x97, 0x4b, 0xa5, 0xd2,
+/* 160 */ 0x69, 0xb4, 0xda, 0xed, 0x76, 0xbb, 0x5d, 0xae, 0xd7, 0x6b,
+/* 170 */ 0xb5, 0x5a, 0xad, 0x56, 0xab, 0xd5, 0x6a, 0x35, 0x1a, 0x8d,
+/* 180 */ 0x46, 0x23, 0x11, 0x88, 0x44, 0x22, 0x91, 0xc8, 0x64, 0x32,
+/* 190 */ 0x19, 0x0c, 0x86, 0x43, 0x21, 0x10, 0x08, 0x04, 0x02, 0x81,
+/* 200 */ 0x40, 0xa0, 0xd0, 0x68, 0x34, 0x9a, 0xcd, 0x66, 0x33, 0x99,
+/* 210 */ 0x4c, 0xa6, 0x53, 0xa9, 0xd4, 0xea, 0x75, 0x3a, 0x9d, 0xce,
+/* 220 */ 0xe7, 0xf3, 0xf9, 0x7c, 0x3e, 0x1f, 0x8f, 0x47, 0xa3, 0x51,
+/* 230 */ 0xa8, 0x54, 0xaa, 0x55, 0x2a, 0x15, 0x0a, 0x05, 0x82, 0xc1,
+/* 240 */ 0x60, 0xb0, 0x58, 0xac, 0xd6, 0xeb, 0xf5, 0x7a, 0xbd, 0xde,
+/* 250 */ 0x6f, 0x37, 0x1b, 0x0d, 0x06, 0x03, 0x01,
+};
+
+#define REF_PERIOD_PS 9259 /* period of reference clock in ps */
+
+static int calc_pll(int period_ps, struct gxt4500_par *par)
+{
+ int m, n, pdiv1, pdiv2, postdiv;
+ int pll_period, best_error, t;
+
+ /* only deal with range 1MHz - 135MHz */
+ if (period_ps < 7407 || period_ps > 1000000)
+ return -1;
+
+ best_error = 1000000;
+ for (pdiv1 = 1; pdiv1 <= 8; ++pdiv1) {
+ for (pdiv2 = 1; pdiv2 <= pdiv1; ++pdiv2) {
+ postdiv = pdiv1 * pdiv2;
+ pll_period = (period_ps + postdiv - 1) / postdiv;
+ /* keep pll in range 500..1250 MHz */
+ if (pll_period < 800 || pll_period > 2000)
+ continue;
+ for (m = 3; m <= 40; ++m) {
+ n = REF_PERIOD_PS * m * postdiv / period_ps;
+ if (n < 5 || n > 256)
+ continue;
+ t = REF_PERIOD_PS * m * postdiv / n;
+ t -= period_ps;
+ if (t >= 0 && t < best_error) {
+ par->pll_m = m;
+ par->pll_n = n;
+ par->pll_pd1 = pdiv1;
+ par->pll_pd2 = pdiv2;
+ best_error = t;
+ }
+ }
+ }
+ }
+ if (best_error == 1000000)
+ return -1;
+ return 0;
+}
+
+static int calc_pixclock(struct gxt4500_par *par)
+{
+ return REF_PERIOD_PS * par->pll_m * par->pll_pd1 * par->pll_pd2
+ / par->pll_n;
+}
+
+static int gxt4500_var_to_par(struct fb_var_screeninfo *var,
+ struct gxt4500_par *par)
+{
+ if (var->xres + var->xoffset > var->xres_virtual ||
+ var->yres + var->yoffset > var->yres_virtual ||
+ var->xres_virtual > 4096)
+ return -EINVAL;
+ if ((var->vmode & FB_VMODE_MASK) != FB_VMODE_NONINTERLACED)
+ return -EINVAL;
+
+ if (calc_pll(var->pixclock, par) < 0)
+ return -EINVAL;
+
+ switch (var->bits_per_pixel) {
+ case 32:
+ if (var->transp.length)
+ par->pixfmt = DFA_PIX_32BIT;
+ else
+ par->pixfmt = DFA_PIX_24BIT;
+ break;
+ case 24:
+ par->pixfmt = DFA_PIX_24BIT;
+ break;
+ case 16:
+ if (var->green.length == 5)
+ par->pixfmt = DFA_PIX_16BIT_1555;
+ else
+ par->pixfmt = DFA_PIX_16BIT_565;
+ break;
+ case 8:
+ par->pixfmt = DFA_PIX_8BIT;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static struct fb_bitfield eightbits = {0, 8};
+static struct fb_bitfield nobits = {0, 0};
+
+static void gxt4500_unpack_pixfmt(struct fb_var_screeninfo *var,
+ int pixfmt)
+{
+ var->bits_per_pixel = pixsize[pixfmt] * 8;
+ var->red = eightbits;
+ var->green = eightbits;
+ var->blue = eightbits;
+ var->transp = nobits;
+
+ switch (pixfmt) {
+ case DFA_PIX_16BIT_565:
+ var->red.length = 5;
+ var->green.length = 6;
+ var->blue.length = 5;
+ break;
+ case DFA_PIX_16BIT_1555:
+ var->red.length = 5;
+ var->green.length = 5;
+ var->blue.length = 5;
+ var->transp.length = 1;
+ break;
+ case DFA_PIX_32BIT:
+ var->transp.length = 8;
+ break;
+ }
+ if (pixfmt != DFA_PIX_8BIT) {
+ var->green.offset = var->red.length;
+ var->blue.offset = var->green.offset + var->green.length;
+ if (var->transp.length)
+ var->transp.offset =
+ var->blue.offset + var->blue.length;
+ }
+}
+
+static int gxt4500_check_var(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ struct gxt4500_par par;
+ int err;
+
+ par = *(struct gxt4500_par *)info->par;
+ err = gxt4500_var_to_par(var, &par);
+ if (!err) {
+ var->pixclock = calc_pixclock(&par);
+ gxt4500_unpack_pixfmt(var, par.pixfmt);
+ }
+ return err;
+}
+
+static int gxt4500_set_par(struct fb_info *info)
+{
+ struct gxt4500_par *par = info->par;
+ struct fb_var_screeninfo *var = &info->var;
+ int err;
+ u32 ctrlreg;
+ unsigned int dfa_ctl, pixfmt, stride;
+ unsigned int wid_tiles, i;
+ struct gxt4500_par save_par;
+
+ save_par = *par;
+ err = gxt4500_var_to_par(var, par);
+ if (err) {
+ *par = save_par;
+ return err;
+ }
+
+ /* turn off DTG for now */
+ ctrlreg = readreg(par, DTG_CONTROL);
+ ctrlreg &= ~(DTG_CTL_ENABLE | DTG_CTL_SCREEN_REFRESH);
+ writereg(par, DTG_CONTROL, ctrlreg);
+
+ /* set PLL registers */
+ writereg(par, PLL_M, mdivtab[par->pll_m - 1]);
+ writereg(par, PLL_N, ndivtab[par->pll_n - 2]);
+ writereg(par, PLL_POSTDIV,
+ ((8 - par->pll_pd1) << 3) | (8 - par->pll_pd2));
+ msleep(20);
+
+ /* turn off hardware cursor */
+ writereg(par, CURSOR_MODE, CURSOR_MODE_OFF);
+
+ /* reset raster engine */
+ writereg(par, CTRL_REG0, CR0_RASTER_RESET | (CR0_RASTER_RESET << 16));
+ udelay(10);
+ writereg(par, CTRL_REG0, CR0_RASTER_RESET << 16);
+
+ /* set display timing generator registers */
+ writereg(par, DTG_HORIZ_EXTENT,
+ var->xres + var->left_margin + var->right_margin +
+ var->hsync_len - 1);
+ writereg(par, DTG_HORIZ_DISPLAY, var->xres - 1);
+ writereg(par, DTG_HSYNC_START, var->xres + var->right_margin - 1);
+ writereg(par, DTG_HSYNC_END,
+ var->xres + var->right_margin + var->hsync_len - 1);
+ writereg(par, DTG_HSYNC_END_COMP,
+ var->xres + var->right_margin + var->hsync_len - 1);
+ writereg(par, DTG_VERT_EXTENT,
+ var->yres + var->upper_margin + var->lower_margin +
+ var->vsync_len - 1);
+ writereg(par, DTG_VERT_DISPLAY, var->yres - 1);
+ writereg(par, DTG_VSYNC_START, var->yres + var->lower_margin - 1);
+ writereg(par, DTG_VSYNC_END,
+ var->yres + var->lower_margin + var->vsync_len - 1);
+ ctrlreg |= DTG_CTL_ENABLE | DTG_CTL_SCREEN_REFRESH;
+ writereg(par, DTG_CONTROL, ctrlreg);
+
+ /* calculate stride in DFA aperture */
+ if (var->xres_virtual > 2048) {
+ stride = 4096;
+ dfa_ctl = DFA_FB_STRIDE_4k;
+ } else if (var->xres_virtual > 1024) {
+ stride = 2048;
+ dfa_ctl = DFA_FB_STRIDE_2k;
+ } else {
+ stride = 1024;
+ dfa_ctl = DFA_FB_STRIDE_1k;
+ }
+
+ /* Set up framebuffer definition */
+ wid_tiles = (var->xres_virtual + 63) >> 6;
+
+ /* XXX add proper FB allocation here someday */
+ writereg(par, FB_AB_CTRL, FB_CTRL_TYPE | (wid_tiles << 16) | 0);
+ writereg(par, REFRESH_AB_CTRL, FB_CTRL_TYPE | (wid_tiles << 16) | 0);
+ writereg(par, FB_CD_CTRL, FB_CTRL_TYPE | (wid_tiles << 16) | 0);
+ writereg(par, REFRESH_CD_CTRL, FB_CTRL_TYPE | (wid_tiles << 16) | 0);
+ writereg(par, REFRESH_START, (var->xoffset << 16) | var->yoffset);
+ writereg(par, REFRESH_SIZE, (var->xres << 16) | var->yres);
+
+ /* Set up framebuffer access by CPU */
+
+ pixfmt = par->pixfmt;
+ dfa_ctl |= DFA_FB_ENABLE | pixfmt;
+ writereg(par, DFA_FB_A, dfa_ctl);
+
+ /*
+ * Set up window attribute table.
+ * We set all WAT entries the same so it doesn't matter what the
+ * window ID (WID) plane contains.
+ */
+ for (i = 0; i < 32; ++i) {
+ writereg(par, WAT_FMT + (i << 4), watfmt[pixfmt]);
+ writereg(par, WAT_CMAP_OFFSET + (i << 4), 0);
+ writereg(par, WAT_CTRL + (i << 4), 0);
+ writereg(par, WAT_GAMMA_CTRL + (i << 4), WAT_GAMMA_DISABLE);
+ }
+
+ info->fix.line_length = stride * pixsize[pixfmt];
+ info->fix.visual = (pixfmt == DFA_PIX_8BIT)? FB_VISUAL_PSEUDOCOLOR:
+ FB_VISUAL_DIRECTCOLOR;
+
+ return 0;
+}
+
+static int gxt4500_setcolreg(unsigned int reg, unsigned int red,
+ unsigned int green, unsigned int blue,
+ unsigned int transp, struct fb_info *info)
+{
+ u32 cmap_entry;
+ struct gxt4500_par *par = info->par;
+
+ if (reg > 1023)
+ return 1;
+ cmap_entry = ((transp & 0xff00) << 16) | ((blue & 0xff00) << 8) |
+ (green & 0xff00) | (red >> 8);
+ writereg(par, CMAP + reg * 4, cmap_entry);
+
+ if (reg < 16 && par->pixfmt != DFA_PIX_8BIT) {
+ u32 *pal = info->pseudo_palette;
+ u32 val = reg;
+ switch (par->pixfmt) {
+ case DFA_PIX_16BIT_565:
+ val |= (reg << 11) | (reg << 6);
+ break;
+ case DFA_PIX_16BIT_1555:
+ val |= (reg << 10) | (reg << 5);
+ break;
+ case DFA_PIX_32BIT:
+ val |= (reg << 24);
+ /* fall through */
+ case DFA_PIX_24BIT:
+ val |= (reg << 16) | (reg << 8);
+ break;
+ }
+ pal[reg] = val;
+ }
+
+ return 0;
+}
+
+static int gxt4500_pan_display(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ struct gxt4500_par *par = info->par;
+
+ if (var->xoffset & 7)
+ return -EINVAL;
+ if (var->xoffset + var->xres > var->xres_virtual ||
+ var->yoffset + var->yres > var->yres_virtual)
+ return -EINVAL;
+
+ writereg(par, REFRESH_START, (var->xoffset << 16) | var->yoffset);
+ return 0;
+}
+
+static struct fb_fix_screeninfo gxt4500_fix __devinitdata = {
+ .id = "IBM GXT4500P",
+ .type = FB_TYPE_PACKED_PIXELS,
+ .visual = FB_VISUAL_PSEUDOCOLOR,
+ .xpanstep = 8,
+ .ypanstep = 1,
+ .mmio_len = 0x20000,
+};
+
+static struct fb_ops gxt4500_ops = {
+ .owner = THIS_MODULE,
+ .fb_check_var = gxt4500_check_var,
+ .fb_set_par = gxt4500_set_par,
+ .fb_setcolreg = gxt4500_setcolreg,
+ .fb_pan_display = gxt4500_pan_display,
+ .fb_fillrect = cfb_fillrect,
+ .fb_copyarea = cfb_copyarea,
+ .fb_imageblit = cfb_imageblit,
+};
+
+/* PCI functions */
+static int __devinit gxt4500_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ int err;
+ unsigned long reg_phys, fb_phys;
+ struct gxt4500_par *par;
+ struct fb_info *info;
+ struct fb_var_screeninfo var;
+
+ err = pci_enable_device(pdev);
+ if (err) {
+ dev_err(&pdev->dev, "gxt4500: cannot enable PCI device: %d\n",
+ err);
+ return err;
+ }
+
+ reg_phys = pci_resource_start(pdev, 0);
+ if (!request_mem_region(reg_phys, pci_resource_len(pdev, 0),
+ "gxt4500 regs")) {
+ dev_err(&pdev->dev, "gxt4500: cannot get registers\n");
+ goto err_nodev;
+ }
+
+ fb_phys = pci_resource_start(pdev, 1);
+ if (!request_mem_region(fb_phys, pci_resource_len(pdev, 1),
+ "gxt4500 FB")) {
+ dev_err(&pdev->dev, "gxt4500: cannot get framebuffer\n");
+ goto err_free_regs;
+ }
+
+ info = framebuffer_alloc(sizeof(struct gxt4500_par), &pdev->dev);
+ if (!info) {
+ dev_err(&pdev->dev, "gxt4500: cannot alloc FB info record");
+ goto err_free_fb;
+ }
+ par = info->par;
+ info->fix = gxt4500_fix;
+ info->pseudo_palette = par->pseudo_palette;
+
+ info->fix.mmio_start = reg_phys;
+ par->regs = ioremap(reg_phys, pci_resource_len(pdev, 0));
+ if (!par->regs) {
+ dev_err(&pdev->dev, "gxt4500: cannot map registers\n");
+ goto err_free_all;
+ }
+
+ info->fix.smem_start = fb_phys;
+ info->fix.smem_len = pci_resource_len(pdev, 1);
+ info->screen_base = ioremap(fb_phys, pci_resource_len(pdev, 1));
+ if (!info->screen_base) {
+ dev_err(&pdev->dev, "gxt4500: cannot map framebuffer\n");
+ goto err_unmap_regs;
+ }
+
+ pci_set_drvdata(pdev, info);
+
+ /* Set byte-swapping for DFA aperture for all pixel sizes */
+ pci_write_config_dword(pdev, CFG_ENDIAN0, 0x333300);
+
+ info->fbops = &gxt4500_ops;
+ info->flags = FBINFO_FLAG_DEFAULT;
+
+ err = fb_alloc_cmap(&info->cmap, 256, 0);
+ if (err) {
+ dev_err(&pdev->dev, "gxt4500: cannot allocate cmap\n");
+ goto err_unmap_all;
+ }
+
+ if (!fb_find_mode(&var, info, mode_option, NULL, 0, &defaultmode, 8)) {
+ dev_err(&pdev->dev, "gxt4500: cannot find valid video mode\n");
+ goto err_free_cmap;
+ }
+ info->var = var;
+ if (gxt4500_set_par(info)) {
+ printk(KERN_ERR "gxt4500: cannot set video mode\n");
+ goto err_free_cmap;
+ }
+
+ if (register_framebuffer(info) < 0) {
+ dev_err(&pdev->dev, "gxt4500: cannot register framebuffer\n");
+ goto err_free_cmap;
+ }
+ printk(KERN_INFO "fb%d: %s frame buffer device\n",
+ info->node, info->fix.id);
+
+ return 0;
+
+ err_free_cmap:
+ fb_dealloc_cmap(&info->cmap);
+ err_unmap_all:
+ iounmap(info->screen_base);
+ err_unmap_regs:
+ iounmap(par->regs);
+ err_free_all:
+ framebuffer_release(info);
+ err_free_fb:
+ release_mem_region(fb_phys, pci_resource_len(pdev, 1));
+ err_free_regs:
+ release_mem_region(reg_phys, pci_resource_len(pdev, 0));
+ err_nodev:
+ return -ENODEV;
+}
+
+static void __devexit gxt4500_remove(struct pci_dev *pdev)
+{
+ struct fb_info *info = pci_get_drvdata(pdev);
+ struct gxt4500_par *par;
+
+ if (!info)
+ return;
+ par = info->par;
+ unregister_framebuffer(info);
+ fb_dealloc_cmap(&info->cmap);
+ iounmap(par->regs);
+ iounmap(info->screen_base);
+ release_mem_region(pci_resource_start(pdev, 0),
+ pci_resource_len(pdev, 0));
+ release_mem_region(pci_resource_start(pdev, 1),
+ pci_resource_len(pdev, 1));
+ framebuffer_release(info);
+}
+
+/* supported chipsets */
+static struct pci_device_id gxt4500_pci_tbl[] = {
+ { PCI_VENDOR_ID_IBM, PCI_DEVICE_ID_IBM_GXT4500P,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
+ { 0 }
+};
+
+MODULE_DEVICE_TABLE(pci, gxt4500_pci_tbl);
+
+static struct pci_driver gxt4500_driver = {
+ .name = "gxt4500",
+ .id_table = gxt4500_pci_tbl,
+ .probe = gxt4500_probe,
+ .remove = __devexit_p(gxt4500_remove),
+};
+
+static int __devinit gxt4500_init(void)
+{
+#ifndef MODULE
+ if (fb_get_options("gxt4500", &mode_option))
+ return -ENODEV;
+#endif
+
+ return pci_register_driver(&gxt4500_driver);
+}
+module_init(gxt4500_init);
+
+static void __exit gxt4500_exit(void)
+{
+ pci_unregister_driver(&gxt4500_driver);
+}
+module_exit(gxt4500_exit);
+
+MODULE_AUTHOR("Paul Mackerras <paulus at samba.org>");
+MODULE_DESCRIPTION("FBDev driver for IBM GXT4500P");
+MODULE_LICENSE("GPL");
+module_param(mode_option, charp, 0);
+MODULE_PARM_DESC(mode_option, "Specify resolution as \"<xres>x<yres>[-<bpp>][@<refresh>]\"");
More information about the Linuxppc-dev
mailing list