2.6.11 prep image on radstone ppc4a not booting
Brian V. Madzarevic
Brian.Madzarevic at uav.com
Wed Mar 9 05:11:31 EST 2005
I am trying to boot a Linux 2.6.11 prep image on a Radstone PPC4A.
PPC4A Specifications http://www.radstone.com/rtcd/pdfs/ppc4a.pdf
I was trying to get an nfs filesystem mounted, but after the bios
retrieves the kernel using tftp, no more packets are even sent out. I
don't know if there is a problem with the network driver or the PCI bus
or what.
Here is my boot log:
Radstone Technology.
SilverChip PowerPC PReP Boot Firmware
Version: 4.05
Built (Jan 20 2004 10:34:02)
PPC4a-7400 333MHz, 83MHz Bus Rev. 3B Ser. No. 0003815 ID No. 0xd
PCI devices
0 0 ID 0x00021057 Motorola MPC106 PowerPC Chipset, Rev. 4.0
0 1 Fn 0 ID 0x056510ad Winbond W83C553F ISA bridge, Rev. 1.0
0 1 Fn 1 ID 0x010510ad Winbond W83C553F IDE controller, Rev. 0.5
0 2 ID 0x00061000 LSI 53C860 Ultra SCSI/Narrow, Rev. 0.2
0 3 ID 0x00191011 DEC DC21143 PCI/CardBus 10/100 Mbit Ethernet Ctlr,
Rev. 4.1
0 4 ID 0x000010e3 Tundra CA91C042 VMEbus Bridge, Rev. 0.1
2 Mbytes of L2 cache on a 133MHz cache bus
128 Mbytes of SDRAM
Floppy drive 0
Floppy drive 1
SCSI id 0
SCSI id 1
SCSI id 2
SCSI id 3
SCSI id 4
SCSI id 5
SCSI id 6
No keyboard found. Using COM1 for input.
No boot authentication required
Opening File
"multi()net()server(192.168.1.73)clientip(192.168.1.147)brian26.prp"
Loading ...
loaded at: 00800400 00912F4C
relocated to: 00800000 00912B4C
zimage at: 0080A86C 00909B2E
avail ram: 00400000 00800000
Linux/PPC load: console=ttyS0,9600 console=tty0 panic=0 root=/dev/nfs
nfsroot=192.168.1.73:/export/nfsroot
ip=192.168.1.147:192.168.1.73::255.255.255.0::eth0
Uncompressing Linux...done.
Now booting the kernel
Total memory = 128MB; using 256kB for hash table (at c0240000)
Linux version 2.6.11 (brian at rex) (gcc version 3.4.1) #6 Mon Mar 7
15:50:16 PST 2005
PReP architecture
Built 1 zonelists
Kernel command line: console=ttyS0,9600 console=tty0 panic=0
root=/dev/nfs nfsroot=192.168.1.73:/export/nfsroot
ip=192.168.1.147:192.168.1.73::255.255.255.0::eth0
PID hash table entries: 1024 (order: 10, 16384 bytes)
TODC real-time-clock was stopped. Now starting...
time_init: decrementer frequency = 20.833333 MHz
Warning: real time clock seems stuck!
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 127232k available (1512k kernel code, 640k data, 136k init, 0k
highmem)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
NET: Registered protocol family 16
PCI: Probing PCI hardware
Setting PCI interrupts for a "Blackhawk (Powerstack)"
PCI: Cannot allocate resource region 0 of device 0000:00:0b.1
PCI: Cannot allocate resource region 1 of device 0000:00:0b.1
PCI: Cannot allocate resource region 2 of device 0000:00:0b.1
PCI: Cannot allocate resource region 3 of device 0000:00:0b.1
PCI: Cannot allocate resource region 4 of device 0000:00:0b.1
PCI: Cannot allocate resource region 5 of device 0000:00:0b.1
PCI: Cannot allocate resource region 0 of device 0000:00:0c.0
PCI: Cannot allocate resource region 0 of device 0000:00:0d.0
PCI: Cannot allocate resource region 0 of device 0000:00:0e.0
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
PCI: I/O Region 0000:00:0e.0/0 too large (4096 bytes)
Generic RTC Driver v1.07
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing
disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Linux Tulip driver version 1.1.13 (May 11, 2002)
tulip0: EEPROM default media type Autosense.
tulip0: Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0)
block.
tulip0: Index #1 - Media 10base2 (#1) described by a <unknown> (8)
block.
tulip0: Index #2 - Media 10baseT (#0) described by a 21140 non-MII (0)
block.
tulip0: Index #3 - Media 10baseT (#0) described by a 21140 non-MII (0)
block.
eth0: Digital DS21143 Tulip rev 65 at 80001080, 00:80:8E:00:5D:5B, IRQ
0.
mice: PS/2 mouse device common for all mice
atkbd.c: keyboard reset failed on isa0060/serio1
atkbd.c: keyboard reset failed on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
IP-Config: Complete:
device=eth0, addr=192.168.1.147, mask=255.255.255.0,
gw=255.255.255.255,
host=192.168.1.147, domain=, nis-domain=(none),
bootserver=192.168.1.73, rootserver=192.168.1.73, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.73
portmap: server 192.168.1.73 not responding, timed out
Root-NFS: Unable to get nfsd port number from server, using default
Looking up port of RPC 100005/1 on 192.168.1.73
portmap: server 192.168.1.73 not responding, timed out
Root-NFS: Unable to get mountd port number from server, using default
NETDEV WATCHDOG: eth0: transmit timed out
eth0: 21140 transmit timed out, status f8678105, SIA 000000c5 ffff0001
fffbff7f 8ff04008, resetting...
eth0: transmit timed out, switching to 100baseTx media.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: 21140 transmit timed out, status f8278517, SIA 000000cb ffff0001
fffbff7f 8ff04008, resetting...
eth0: transmit timed out, switching to 10baseT media.
NETDEV WATCHDOG: eth0: transmit timed out
eth0: 21140 transmit timed out, status f8678117, SIA 000000cb ffff0001
fffbff7f 8ff04008, resetting...
eth0: transmit timed out, switching to 10baseT media.
mount: server 192.168.1.73 not responding, timed out
Root-NFS: Server returned error -5 while mounting /export/nfsroot
VFS: Unable to mount root fs via NFS, trying floppy.
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(2,0)
<6>NETDEV WATCHDOG: eth0: transmit timed out
eth0: 21140 transmit timed out, status f8278517, SIA 000000cb ffff0001
fffbff7f 8ff04008, resetting...
eth0: transmit timed out, switching to 10baseT media.
Here is my .config file:
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.11
# Mon Mar 7 15:44:49 2005
#
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_HAVE_DEC_LOCK=y
CONFIG_PPC=y
CONFIG_PPC32=y
CONFIG_GENERIC_NVRAM=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
# CONFIG_CLEAN_COMPILE is not set
CONFIG_BROKEN=y
CONFIG_BROKEN_ON_SMP=y
#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_FUTEX=y
CONFIG_EPOLL=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
CONFIG_KMOD=y
#
# Processor
#
CONFIG_6xx=y
# CONFIG_40x is not set
# CONFIG_44x is not set
# CONFIG_POWER3 is not set
# CONFIG_POWER4 is not set
# CONFIG_8xx is not set
# CONFIG_E500 is not set
# CONFIG_ALTIVEC is not set
# CONFIG_TAU is not set
# CONFIG_CPU_FREQ is not set
# CONFIG_PPC601_SYNC_FIX is not set
CONFIG_PPC_STD_MMU=y
#
# Platform options
#
CONFIG_PPC_MULTIPLATFORM=y
# CONFIG_APUS is not set
# CONFIG_KATANA is not set
# CONFIG_WILLOW is not set
# CONFIG_CPCI690 is not set
# CONFIG_PCORE is not set
# CONFIG_POWERPMC250 is not set
# CONFIG_CHESTNUT is not set
# CONFIG_SPRUCE is not set
# CONFIG_EV64260 is not set
# CONFIG_LOPEC is not set
# CONFIG_MCPN765 is not set
# CONFIG_MVME5100 is not set
# CONFIG_PPLUS is not set
# CONFIG_PRPMC750 is not set
# CONFIG_PRPMC800 is not set
# CONFIG_SANDPOINT is not set
# CONFIG_ADIR is not set
# CONFIG_K2 is not set
# CONFIG_PAL4 is not set
# CONFIG_GEMINI is not set
# CONFIG_EST8260 is not set
# CONFIG_SBC82xx is not set
# CONFIG_SBS8260 is not set
# CONFIG_RPX8260 is not set
# CONFIG_TQM8260 is not set
# CONFIG_ADS8272 is not set
# CONFIG_PQ2FADS is not set
# CONFIG_LITE5200 is not set
CONFIG_PPC_CHRP=y
CONFIG_PPC_PMAC=y
CONFIG_PPC_PREP=y
CONFIG_PPC_OF=y
CONFIG_PPCBUG_NVRAM=y
# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
# CONFIG_HIGHMEM is not set
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
# CONFIG_PROC_DEVICETREE is not set
CONFIG_PREP_RESIDUAL=y
CONFIG_PROC_PREPRESIDUAL=y
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="console=ttyS0,9600 console=tty0 panic=0 root=/dev/nfs
nfsroot=192.168.1.73:/export/nfsroot
ip=192.168.1.147:192.168.1.73::255.255.255.0::eth0"
#
# Bus options
#
# CONFIG_ISA is not set
CONFIG_GENERIC_ISA_DMA=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
# CONFIG_PCI_LEGACY_PROC is not set
# CONFIG_PCI_NAMES is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# PC-card bridges
#
#
# Advanced setup
#
# CONFIG_ADVANCED_OPTIONS is not set
#
# Default settings for advanced configuration options are used
#
CONFIG_HIGHMEM_START=0xfe000000
CONFIG_LOWMEM_SIZE=0x30000000
CONFIG_KERNEL_START=0xc0000000
CONFIG_TASK_SIZE=0x80000000
CONFIG_BOOT_LOAD=0x00800000
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
#
# Block devices
#
# CONFIG_BLK_DEV_FD is not set
# CONFIG_MAC_FLOPPY is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_RAM is not set
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_LBD is not set
# CONFIG_CDROM_PKTCDVD is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
#
# CONFIG_IDE is not set
#
# SCSI device support
#
CONFIG_SCSI=m
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=m
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
#
# SCSI Transport Attributes
#
CONFIG_SCSI_SPI_ATTRS=m
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
CONFIG_SCSI_SYM53C8XX_2=m
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64
# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=m
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
# CONFIG_SCSI_MESH is not set
# CONFIG_SCSI_MAC53C94 is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
#
# Macintosh device drivers
#
# CONFIG_ADB is not set
# CONFIG_ADB_CUDA is not set
# CONFIG_ADB_PMU is not set
# CONFIG_MAC_SERIAL is not set
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_IP_TCPDIAG=y
# CONFIG_IP_TCPDIAG_IPV6 is not set
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_MII is not set
# CONFIG_MACE is not set
# CONFIG_BMAC is not set
# CONFIG_OAKNET is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
#
# Tulip family network device support
#
CONFIG_NET_TULIP=y
# CONFIG_DE2104X is not set
CONFIG_TULIP=y
# CONFIG_TULIP_MWI is not set
# CONFIG_TULIP_MMIO is not set
# CONFIG_TULIP_NAPI is not set
# CONFIG_DE4X5 is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_DM9102 is not set
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_PMACZILOG is not set
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_NVRAM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_AGP is not set
# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
#
# I2C support
#
# CONFIG_I2C is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Misc devices
#
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
# CONFIG_FB is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
#
# Sound
#
# CONFIG_SOUND is not set
#
# USB support
#
# CONFIG_USB is not set
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be
needed; see USB_STORAGE Help for more information
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set
#
# File systems
#
# CONFIG_EXT2_FS is not set
# CONFIG_EXT3_FS is not set
# CONFIG_JBD is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
#
# XFS support
#
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set
#
# DOS/FAT/NT Filesystems
#
# CONFIG_MSDOS_FS is not set
# CONFIG_VFAT_FS is not set
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_TMPFS_XATTR is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
# CONFIG_NLS is not set
#
# Library routines
#
# CONFIG_CRC_CCITT is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
#
# Profiling support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_KGDB is not set
CONFIG_XMON=y
# CONFIG_BDI_SWITCH is not set
CONFIG_BOOTX_TEXT=y
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
# CONFIG_CRYPTO is not set
#
# Hardware crypto devices
#
More information about the Linuxppc-dev
mailing list