Apple G4 "windtunnel" fan controller
Samuel Rydh
samuel at ibrium.se
Sun Mar 16 05:41:12 EST 2003
Attached is a fan controller for Apple's SMP machines. On my machine,
the noise level is reduced from "very loud PC" to "silent mac".
I have only tested the code on Apple's latest 1.25 GHz model
(windtunnel?). The driver might need some tuning on other models for
optimal performance. (The code is based upon the behavior
of Apple's AppleFan driver under OSX. However, the source
code is not available so I had to reverse engineer it
by inspecting the i2c traffic.)
It ought to be safe to use this patch (there is a 100% fan
trigger when the temperature rises sufficiently). However
I TAKE NO RESPONSIBILITY WHAT SO EVER IF THIS PATCH DOES NOT
WORK AS IT SHOULD AND THE COMPUTER OVERHEATS.
For testing purposes, it is useful to set 'LOG_TEMP is set to 1'.
/Samuel
diff -urN benh-org/drivers/i2c/Config.in benh-2.4/drivers/i2c/Config.in
--- benh-org/drivers/i2c/Config.in 2003-03-15 19:02:28.000000000 +0100
+++ benh-2.4/drivers/i2c/Config.in 2003-03-15 19:11:08.000000000 +0100
@@ -41,6 +41,9 @@
if [ "$CONFIG_ALL_PPC" = "y" ] ; then
dep_tristate 'Keywest I2C interface in Apple Core99 machines' CONFIG_I2C_KEYWEST $CONFIG_I2C
+ if [ "CONFIG_I2C_KEYWEST" != "n" ] ; then
+ dep_tristate ' Apple G4 "windtunnel" fan controller (experimental)' CONFIG_G4FAN $CONFIG_I2C_KEYWEST
+ fi
fi
# This is needed for automatic patch generation: sensors code starts here
diff -urN benh-org/drivers/i2c/Makefile benh-2.4/drivers/i2c/Makefile
--- benh-org/drivers/i2c/Makefile 2003-03-15 19:02:28.000000000 +0100
+++ benh-2.4/drivers/i2c/Makefile 2003-03-15 18:33:06.000000000 +0100
@@ -19,6 +19,8 @@
obj-$(CONFIG_ITE_I2C_ADAP) += i2c-adap-ite.o
obj-$(CONFIG_I2C_PROC) += i2c-proc.o
obj-$(CONFIG_I2C_KEYWEST) += i2c-keywest.o
+obj-$(CONFIG_G4FAN) += g4fan.o
+
# This is needed for automatic patch generation: sensors code starts here
# This is needed for automatic patch generation: sensors code ends here
diff -urN benh-org/drivers/i2c/g4fan.c benh-2.4/drivers/i2c/g4fan.c
--- benh-org/drivers/i2c/g4fan.c Thu Jan 01 01:00:00 1970
+++ benh-2.4/drivers/i2c/g4fan.c Sat Mar 15 18:55:53 2003
@@ -0,0 +1,455 @@
+/*
+ * Creation Date: <2003/03/14 20:54:13 samuel>
+ * Time-stamp: <2003/03/15 18:55:53 samuel>
+ *
+ * <g4fan.c>
+ *
+ * The G4 "windtunnel" has a single fan controlled by a
+ * DS1775 fan controller and an ADM1030 thermostat.
+ *
+ * The fan controller is equipped with a temperature sensor
+ * which measures the case temperature. The ADM censor
+ * measures the CPU temperature. This driver tunes the
+ * behavior of the fan. It is based upon empirical observations
+ * of the 'AppleFan' driver under OSX.
+ *
+ * WARNING: This driver has only been testen on Apple's
+ * 1.25 MHz Dual G4 (March 03). Other machines might have
+ * a different thermal design. It is tuned for a CPU
+ * temperatur around 57 C.
+ *
+ * Copyright (C) 2003 Samuel Rydh (samuel at ibrium.se)
+ *
+ * Loosely based upon 'thermostat.c' written by Benjamin Herrenschmidt
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/sched.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <asm/prom.h>
+#include <asm/machdep.h>
+#include <asm/io.h>
+#include <asm/system.h>
+#include <asm/sections.h>
+
+MODULE_AUTHOR("Samuel Rydh <samuel at ibrium.se>");
+MODULE_DESCRIPTION("Apple G4 (windtunnel) fan driver");
+MODULE_LICENSE("GPL");
+EXPORT_NO_SYMBOLS;
+
+#define LOG_TEMP 0 /* continously log temperature */
+
+/* scan 0x48-0x4f (DS1775) and 0x2c-2x2f (ADM1030) */
+static unsigned short normal_i2c[] = { 0x49, 0x2c, I2C_CLIENT_END };
+static unsigned short normal_i2c_range[] = { 0x48, 0x4f, 0x2c, 0x2f, I2C_CLIENT_END };
+
+I2C_CLIENT_INSMOD;
+
+#define I2C_DRIVERID_G4FAN 0x9001 /* fixme */
+
+#define THERMOSTAT_CLIENT_ID 1
+#define FAN_CLIENT_ID 2
+
+struct temp_range {
+ u8 high; /* start the fan */
+ u8 low; /* stop the fan */
+};
+struct apple_thermal_info {
+ u8 id; /* implementation ID */
+ u8 fan_count; /* number of fans */
+ u8 thermostat_count; /* number of thermostats */
+ u8 unused[5];
+ struct temp_range ranges[4]; /* temperature ranges (may be [])*/
+};
+
+static int do_detect( struct i2c_adapter *adapter, int addr,
+ unsigned short flags, int kind );
+
+static struct {
+ struct i2c_client *thermostat;
+ struct i2c_client *fan;
+ int error;
+ struct timer_list timer;
+
+ int overheat_temp; /* 100% fan at this temp */
+ int overheat_hyst;
+ int temp;
+ int casetemp;
+ int fan_level; /* active fan_table setting */
+
+ int downind;
+ int upind;
+
+ int r0, r1, r20, r23, r25; /* saved register */
+} x;
+
+static struct {
+ int temp;
+ int fan_setting;
+} fan_up_table[] = {
+ { 0x0000, 11 }, /* min fan */
+ { 0x3900, 8 }, /* 57.0 C */
+ { 0x3a4a, 7 }, /* 58.3 C */
+ { 0x3ad3, 6 }, /* 58.8 C */
+ { 0x3b3c, 5 }, /* 59.2 C */
+ { 0x3b94, 4 }, /* 59.6 C */
+ { 0x3be3, 3 }, /* 58.9 C */
+ { 0x3c29, 2 }, /* 59.2 C */
+ { 0xffff, 1 } /* on fire */
+};
+static struct {
+ int temp;
+ int fan_setting;
+} fan_down_table[] = {
+ { 0x3700, 11 }, /* 55.0 C */
+ { 0x374a, 6 },
+ { 0x3800, 7 }, /* 56.0 C */
+ { 0x3900, 8 }, /* 57.0 C */
+ { 0x3a4a, 7 }, /* 58.3 C */
+ { 0x3ad3, 6 }, /* 58.8 C */
+ { 0x3b3c, 5 }, /* 59.2 C */
+ { 0x3b94, 4 }, /* 58.9 C */
+ { 0x3be3, 3 }, /* 58.9 C */
+ { 0x3c29, 2 }, /* 59.2 C */
+ { 0xffff, 1 }
+};
+
+static int
+write_reg( struct i2c_client *cl, int reg, int data, int len )
+{
+ u8 tmp[3];
+
+ if( len < 1 || len > 2 || data < 0 )
+ return -EINVAL;
+
+ tmp[0] = reg;
+ tmp[1] = (len == 1) ? data : (data >> 8);
+ tmp[2] = data;
+ len++;
+
+ if( i2c_master_send(cl, tmp, len) != len )
+ return -ENODEV;
+ return 0;
+}
+
+static int
+read_reg( struct i2c_client *cl, int reg, int len )
+{
+ u8 buf[2];
+
+ if( len != 1 && len != 2 )
+ return -EINVAL;
+ buf[0] = reg;
+ if( i2c_master_send(cl, buf, 1) != 1 )
+ return -ENODEV;
+ if( i2c_master_recv(cl, buf, len) != len )
+ return -ENODEV;
+ return (len == 2)? ((unsigned int)buf[0] << 8) | buf[1] : buf[0];
+}
+
+
+static void
+print_temp( const char *s, int temp )
+{
+ printk("%s%d.%d C", s ? s : "", temp>>8, (temp & 255)*10/256 );
+}
+
+static void
+tune_fan( int fan_setting )
+{
+ int val = (fan_setting << 3) | 7;
+ x.fan_level = fan_setting;
+
+ //write_reg( x.fan, 0x24, val, 1 );
+ write_reg( x.fan, 0x25, val, 1 );
+ write_reg( x.fan, 0x20, 0, 1 );
+ print_temp("CPU-temp: ", x.temp );
+ if( x.casetemp )
+ print_temp(", Case: ", x.casetemp );
+ printk(" Tuning fan: %d (%02x)\n", fan_setting, val );
+}
+
+static void
+poll_temp( void *param )
+{
+ int temp = read_reg( x.thermostat, 0, 2 );
+ int i, level, casetemp;
+
+ /* this actually occurs when the computer is loaded */
+ if( temp < 0 )
+ goto out;
+
+ casetemp = read_reg(x.fan, 0x0b, 1) << 8;
+ casetemp |= (read_reg(x.fan, 0x06, 1) & 0x7) << 5;
+
+ if( LOG_TEMP && x.temp != temp ) {
+ print_temp("CPU-temp: ", temp );
+ print_temp(", Case: ", casetemp );
+ printk(", Fan: %d\n", x.fan_level );
+ }
+ x.temp = temp;
+ x.casetemp = casetemp;
+
+ level = -1;
+ for( i=0; (temp & 0xffff) > fan_down_table[i].temp ; i++ )
+ ;
+ if( i < x.downind )
+ level = fan_down_table[i].fan_setting;
+ x.downind = i;
+
+ for( i=0; (temp & 0xfffe) >= fan_up_table[i+1].temp ; i++ )
+ ;
+ if( x.upind < i )
+ level = fan_up_table[i].fan_setting;
+ x.upind = i;
+
+ if( level >= 0 )
+ tune_fan( level );
+ out:
+ x.timer.expires = jiffies + 8*HZ;
+ add_timer( &x.timer );
+}
+
+static void
+schedule_poll( unsigned long t )
+{
+ static struct tq_struct tqs = {
+ .routine = poll_temp,
+ };
+ schedule_task( &tqs );
+}
+
+/************************************************************************/
+/* i2c probing and setup */
+/************************************************************************/
+
+static int
+do_attach( struct i2c_adapter *adapter )
+{
+ return i2c_probe( adapter, &addr_data, &do_detect );
+}
+
+static int
+do_detach( struct i2c_client *client )
+{
+ int err;
+
+ printk("do_detach: id %d\n", client->id );
+ if( (err=i2c_detach_client(client)) ) {
+ printk("failed to detach thermostat client\n");
+ return err;
+ }
+ kfree( client );
+ return 0;
+}
+
+static struct i2c_driver g4fan_driver = {
+ .name = "Apple G4 Thermostat/Fan",
+ .id = I2C_DRIVERID_G4FAN,
+ .flags = I2C_DF_NOTIFY,
+ .attach_adapter = &do_attach,
+ .detach_client = &do_detach,
+ .command = NULL,
+ .inc_use = NULL,
+ .dec_use = NULL
+};
+
+static int
+detect_fan( struct i2c_client *cl )
+{
+ /* check that this is an ADM1030 */
+ if( read_reg(cl, 0x3d, 1) != 0x30 || read_reg(cl, 0x3e, 1) != 0x41 )
+ goto out;
+ printk("ADM1030 fan controller detected at %02x\n", cl->addr );
+
+ if( x.fan ) {
+ x.error |= 2;
+ goto out;
+ }
+ x.fan = cl;
+ cl->id = FAN_CLIENT_ID;
+ strncpy( cl->name, "ADM1030 fan controller", sizeof(cl->name) );
+
+ if( i2c_attach_client( cl ) )
+ goto out;
+ return 0;
+ out:
+ if( cl != x.fan )
+ kfree( cl );
+ return 0;
+}
+
+static int
+detect_thermostat( struct i2c_client *cl )
+{
+ int hyst_temp, os_temp, temp;
+
+ if( (temp=read_reg(cl, 0, 2)) < 0 )
+ goto out;
+
+ /* temperature sanity check */
+ if( temp < 0x1600 || temp > 0x3c00 )
+ goto out;
+ hyst_temp = read_reg(cl, 2, 2);
+ os_temp = read_reg(cl, 3, 2);
+ if( hyst_temp < 0 || os_temp < 0 )
+ goto out;
+
+ printk("DS1775 digital thermometer detected at %02x\n", cl->addr );
+ print_temp("Temp: ", temp );
+ print_temp(" Hyst: ", hyst_temp );
+ print_temp(" OS: ", os_temp );
+ printk("\n");
+
+ if( x.thermostat ) {
+ x.error |= 1;
+ goto out;
+ }
+ x.temp = temp;
+ x.thermostat = cl;
+ x.overheat_temp = os_temp;
+ x.overheat_hyst = hyst_temp;
+
+ cl->id = THERMOSTAT_CLIENT_ID;
+ strncpy( cl->name, "DS1775 thermostat", sizeof(cl->name) );
+
+ if( i2c_attach_client( cl ) )
+ goto out;
+ return 0;
+out:
+ kfree( cl );
+ return 0;
+}
+
+static int
+do_detect( struct i2c_adapter *adapter, int addr, unsigned short flags, int kind )
+{
+ struct i2c_client *cl;
+
+ if( strncmp(adapter->name, "uni-n", 5) )
+ return 0;
+ if( !i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA | I2C_FUNC_SMBUS_WRITE_BYTE) )
+ return 0;
+
+ if( !(cl=kmalloc( sizeof(struct i2c_client), GFP_KERNEL )) )
+ return -ENOMEM;
+ memset( cl, 0, sizeof(struct i2c_client) );
+
+ cl->addr = addr;
+ cl->data = NULL;
+ cl->adapter = adapter;
+ cl->driver = &g4fan_driver;
+ cl->flags = 0;
+
+ if( addr < 0x48 )
+ return detect_fan( cl );
+ return detect_thermostat( cl );
+}
+
+#define PRINT_REG( r ) printk("reg %02x = %02x\n", r, read_reg(x.fan, r, 1) )
+
+static int __init
+g4fan_init( void )
+{
+ struct apple_thermal_info *info;
+ struct device_node *np;
+ int ret, val;
+
+ if( !(np=find_devices("power-mgt")) )
+ return -ENODEV;
+ if( !(info=(struct apple_thermal_info*)get_property(np, "thermal-info", NULL)) )
+ return -ENODEV;
+
+ /* check for G4 "Windtunnel" SMP */
+ if( machine_is_compatible("PowerMac3,6") ) {
+ if( info->id != 3 ) {
+ printk(KERN_ERR "g4fan: design id %d unknown\n", info->id);
+ return -ENODEV;
+ }
+ } else {
+ printk(KERN_ERR "g4fan: unsupported machine type\n");
+ return -ENODEV;
+ }
+ if( (ret=i2c_add_driver(&g4fan_driver)) )
+ return ret;
+
+ if( !x.thermostat || !x.fan ) {
+ i2c_del_driver(&g4fan_driver );
+ return -ENODEV;
+ }
+
+ /* save registers (if we unload the module) */
+ x.r0 = read_reg( x.fan, 0x00, 1 );
+ x.r1 = read_reg( x.fan, 0x01, 1 );
+ x.r20 = read_reg( x.fan, 0x20, 1 );
+ x.r23 = read_reg( x.fan, 0x23, 1 );
+ x.r25 = read_reg( x.fan, 0x25, 1 );
+
+ /* improve measurement resolution (convergence time 1.5s) */
+ if( (val=read_reg( x.thermostat, 1, 1 )) >= 0 ) {
+ val |= 0x60;
+ if( write_reg( x.thermostat, 1, val, 1 ) )
+ printk("Failed writing config register\n");
+ }
+ /* disable interrupts and TAC input */
+ write_reg( x.fan, 0x01, 0x01, 1 );
+ /* enable filter */
+ write_reg( x.fan, 0x23, 0x91, 1 );
+ /* remote temp. controls fan */
+ write_reg( x.fan, 0x00, 0x95, 1 );
+
+ /* The thermostat (which besides measureing temperature controls
+ * has a THERM output which puts the fan on 100%) is usually
+ * set to kick in at 80 C (chip default). We reduce this a bit
+ * to be on the safe side (OSX doesn't)...
+ */
+ if( x.overheat_temp == (80 << 8) ) {
+ x.overheat_temp = 65 << 8;
+ x.overheat_hyst = 60 << 8;
+ write_reg( x.thermostat, 2, x.overheat_hyst, 2 );
+ write_reg( x.thermostat, 3, x.overheat_temp, 2 );
+
+ print_temp("Reducing overheating limit to ", x.overheat_temp );
+ print_temp(" (Hyst: ", x.overheat_hyst );
+ printk(")\n");
+ }
+
+ /* set an initial fan setting */
+ x.upind = x.downind = 1;
+ tune_fan( fan_up_table[x.upind].fan_setting );
+
+ init_timer( &x.timer );
+ x.timer.expires = jiffies + 8*HZ;
+ x.timer.function = schedule_poll;
+ add_timer( &x.timer );
+ return 0;
+}
+
+static void __exit
+g4fan_exit( void )
+{
+ del_timer( &x.timer );
+
+ write_reg( x.fan, 0x01, x.r1, 1 );
+ write_reg( x.fan, 0x20, x.r20, 1 );
+ write_reg( x.fan, 0x23, x.r23, 1 );
+ write_reg( x.fan, 0x25, x.r25, 1 );
+ write_reg( x.fan, 0x00, x.r0, 1 );
+
+ i2c_del_driver( &g4fan_driver );
+}
+
+module_init(g4fan_init);
+module_exit(g4fan_exit);
** Sent via the linuxppc-dev mail list. See http://lists.linuxppc.org/
More information about the Linuxppc-dev
mailing list