2.2.0pre2 SCSI problems, more (fwd)

[Brad Midgley]

turning off the target debugging "allowed" the drive to abort again.  log
is appended. 

brad

DB mouse driver installed.
AWACS: error, status = 40210f
DMA sound driver installed, using 4 buffers of 32k.
RAM disk driver initialized:  16 RAM disks of 4096K size
loop: registered device at major 7
fd0: SWIM3 floppy controller 
scsi0 : MESH
scsi1 : 53C94
scsi : 2 hosts.
mesh: target 0 synchronous at 5.0 MB/s
  Vendor: QUANTUM   Model: PD1225S           Rev: 3110
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
mesh: target 1 aborted
mesh log 1: bs=0000 ph=01 start cmd=c2fdbe00
mesh log 1: bs=0000 ph=01 about to arb, intr/exc/err/fc=00000000
mesh log 1: bs=6000 ph=01 after arb, intr/exc/err/fc=01000000
mesh log 1: bs=6000 ph=01 interrupt intr/err/exc/seq=01000001
mesh log 1: bs=6000 ph=01 cmd_complete fc=0
mesh log 1: bs=6000 ph=02 start_phase err/exc/fc/seq = 00000001
mesh log 1: bs=4008 ph=02 interrupt intr/err/exc/seq=01000022
mesh log 1: bs=4008 ph=02 cmd_complete fc=0
mesh log 1: bs=4008 ph=02 Selecting phase at command completion
mesh log 1: bs=4008 ph=03 start_phase err/exc/fc/seq = 00000022
mesh log 1: bs=0000 ph=03 interrupt intr/err/exc/seq=05400000
mesh log 1: bs=0000 ph=03 error err/exc/fc/cl=40000600
mesh log: bs=4013 ph=46 t0 start_phase err/exc/fc/seq = 00000014
mesh log: bs=4017 ph=46 t0 interrupt intr/err/exc/seq=01000018
mesh log: bs=4017 ph=46 t0 cmd_complete fc=1
mesh log: bs=4017 ph=06 t0 msgin msg=01000301
mesh log: bs=4017 ph=06 t0 start_phase err/exc/fc/seq = 00000018
mesh log: bs=4017 ph=06 t0 enbresel intr/exc/err/fc=00000000
mesh log: bs=0000 ph=06 t0 interrupt intr/err/exc/seq=01000009
mesh log: bs=0000 ph=06 t0 cmd_complete fc=0
mesh log: bs=0000 ph=01 t1 start cmd=c2fdbe00
mesh log: bs=0000 ph=01 t1 about to arb, intr/exc/err/fc=00000000
mesh log: bs=6000 ph=01 t1 after arb, intr/exc/err/fc=01000000
mesh log: bs=6000 ph=01 t1 interrupt intr/err/exc/seq=01000001
mesh log: bs=6000 ph=01 t1 cmd_complete fc=0
mesh log: bs=6000 ph=02 t1 start_phase err/exc/fc/seq = 00000001
mesh log: bs=4008 ph=02 t1 interrupt intr/err/exc/seq=01000022
mesh log: bs=4008 ph=02 t1 cmd_complete fc=0
mesh log: bs=4008 ph=02 t1 Selecting phase at command completion
mesh log: bs=4008 ph=03 t1 start_phase err/exc/fc/seq = 00000022
mesh log: bs=0000 ph=03 t1 interrupt intr/err/exc/seq=05400000
mesh log: bs=0000 ph=03 t1 error err/exc/fc/cl=40000600
mesh: target 3 synchronous at 4.2 MB/s
  Vendor: SONY      Model: CD-ROM CDU-8005   Rev: 1.0j
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 3, lun 0
  Vendor: QUANTUM   Model: CTS80S            Rev: 4.2 
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sdb at scsi1, channel 0, id 4, lun 0
scsi : detected 1 SCSI cdrom 2 SCSI disks total.
sr0: disc change detected.
Uniform CDROM driver Revision: 2.51
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2395980 [1169 MB] [1.2 GB]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 166200 [81 MB] [0.1 GB]
eth0: MACE at 00:05:02:e0:03:4f
Partition check:
 sda: sda1 sda2 sda3 sda4 sda5
 sdb: sdb1 sdb2 sdb3 sdb4 sdb5



[[ This message was sent via the linuxppc-dev mailing list. Replies are ]]
[[ not forced back to the list, so be sure to  Cc linuxppc-dev  if your ]]
[[ reply is of general interest. To unsubscribe from linuxppc-dev, send ]]
[[ the message 'unsubscribe' to linuxppc-dev-request at lists.linuxppc.org ]]