[PATCH v18 0/3] Add i2c-mux and eeprom devices for Meta Yosemite4

[Delphine CC Chiu]

From: Ricky CX Wu <ricky.cx.wu.wiwynn at gmail.com>

Changelog:
  - v18
    - Fix warnings for reg_format reporting by dts checking tool.
  - v17
    - Add SoB for the patches.
  - v16
    - Reorganized the patches.
    - Add i2c-mux and resolve the dt-validate errors.
    - Revise Yosemite 4 devicetree for devices behind i2c-mux.
    - Add mctp config and sensors for NIC after i2c-mux on bus 15.
    - Add fan led config for BMC to control according the status of fan.
  - v15
    - Add ISL28022 support
  - v14
    - Add SQ52205 support
    - Add GPIO I6 pin
  - v13
    - Add RTQ6056-support-on-bus-11 
  - v12
    - Fix GPIO linename typo and add missing GPIO pin initial state.
  - v11
    - Revise all GPIO line name with bottom line
  - v10
    - adjust mgm cpld ioexp bus
    - add GPIOO7 name
    - remove mctp driver
  - v9
    - add XDP710 support
    - add RTQ6056 support
    - add MP5990 support
  - v8
    - add fan led config
  - v7
    - Revise pca9506 i2c address
  - v6
    - Revise i2c duty-cycle for meeting 400khz spec
  - v5
    - Support medusa board adc sensors
    - support NIC eeprom
  - v4
    - Re-format gpio linename
    - Revise i2c device node names
    - Split patches by logic changes
  - v3
    - Correct patch for revising gpio name
  - v2
    - Revise mx31790 fan tach config
    - Add mctp config for NIC
    - Support mux to cpld
    - Revise gpio name
  - v1
    - Add gpio and eeprom behind i2c-mux
    - Remove redundant idle-state setting for i2c-mux
    - Enable adc 15, wdt2,spi gpio for yosemite4 use
    - Revise quad mode to dual mode to avoid WP pin influnece the SPI
    - Revise power sensor adm1281 for yosemite4 schematic change
    - Add gpio pca9506 I/O expander for yosemite4 use
    - remove space for adm1272 compatible
    - enable interrupt setting for pca9555
    - add eeprom for yosemite4 medusa board/BSM use
    - remove temperature sensor for yosemite4 schematic change
    - add power sensor for power module reading
    - Revise adc128d818 adc mode for yosemite4 schematic change
    - Revise ina233 for yosemite4 schematic change
    - Remove idle state setting for yosemite4 NIC connection
    - Initialize bmc gpio state
    - Revise mx31790 fan tach config
    - Add mctp config for NIC
    - Support mux to cpld
    - Revise gpio name

Ricky CX Wu (3):
  ARM: dts: aspeed: yosemite4: Revise i2c-mux devices
  ARM: dts: aspeed: yosemite4: add mctp config and sensors for NIC
  ARM: dts: aspeed: yosemite4: add fan led config

 .../aspeed/aspeed-bmc-facebook-yosemite4.dts  | 706 ++++++++++++++++--
 1 file changed, 660 insertions(+), 46 deletions(-)

-- 
2.25.1