[PATCH v2] ARM: dts: aspeed: mtmitchell: Enable NCSI

[Paul Menzel]

Dear Chanh,


Thank you for the patch.

Am 28.02.23 um 11:28 schrieb Chanh Nguyen:
> Support the mac3 (RGMII4) as an NC-SI stack instead of an MDIO PHY.
> 
> The OCP slot #0 and OCP slot #1 use a common the BMC_NCSI signal,

*the* seems a leftover.

> so we use only one of them at the same time. The OCP slot #0 will
> be enabled by PCA9539's setting by default.
> 
> Also, enable the OCP Auxiliary Power during booting.

Is there a reason not to make this a separate commit?


Kind regards,

Paul


> Signed-off-by: Chanh Nguyen <chanh at os.amperecomputing.com>
> ---
> Changes in v2:
>     - Change PCA9539APW node name.                     [Krzysztof]
> ---
>   .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 37 ++++++++++++++++++-
>   1 file changed, 36 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
> index 4b91600eaf62..1e0e88465254 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
> @@ -251,6 +251,14 @@
>   	pinctrl-0 = <&pinctrl_rgmii1_default>;
>   };
>   
> +&mac3 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_rmii4_default>;
> +	clock-names = "MACCLK", "RCLK";
> +	use-ncsi;
> +};
> +
>   &fmc {
>   	status = "okay";
>   	flash at 0 {
> @@ -439,6 +447,26 @@
>   	status = "okay";
>   };
>   
> +&i2c8 {
> +	status = "okay";
> +
> +	gpio at 77 {
> +		compatible = "nxp,pca9539";
> +		reg = <0x77>;
> +		gpio-controller;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		#gpio-cells = <2>;
> +
> +		bmc-ocp0-en-hog {
> +			gpio-hog;
> +			gpios = <7 GPIO_ACTIVE_LOW>;
> +			output-high;
> +			line-name = "bmc-ocp0-en-n";
> +		};
> +	};
> +};
> +
>   &i2c9 {
>   	status = "okay";
>   };
> @@ -530,13 +558,20 @@
>   	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
>   			"host0-reboot-ack-n","host0-ready","host0-shd-req-n",
>   			"host0-shd-ack-n","s0-overtemp-n",
> -	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
> +	/*W0-W7*/	"","ocp-main-pwren","ocp-pgood","",
>   			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
>   	/*X0-X7*/	"i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
>   			"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
>   			"s1-overtemp-n","s1-spi-auth-fail-n",
>   	/*Y0-Y7*/	"","","","","","","","host0-special-boot",
>   	/*Z0-Z7*/	"reset-button","ps0-pgood","ps1-pgood","","","","","";
> +
> +	ocp-aux-pwren-hog {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "ocp-aux-pwren";
> +	};
>   };
>   
>   &gpio1 {