[PATCH] ARM: dts: aspeed: mtmitchell: Enable NCSI

Chanh Nguyen chanh at os.amperecomputing.com
Fri Feb 17 21:21:22 AEDT 2023


Support the mac3 (RGMII4) as an NC-SI stack instead of an MDIO PHY.

The OCP slot #0 and OCP slot #1 use a common the BMC_NCSI signal,
so we use only one of them at the same time. The OCP slot #0 will
be enabled by PCA9539's setting by default.

Also, enable the OCP Auxiliary Power during booting.

Signed-off-by: Chanh Nguyen <chanh at os.amperecomputing.com>
---
 .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 37 ++++++++++++++++++-
 1 file changed, 36 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
index 4b91600eaf62..e8a6b1f08d6a 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
@@ -251,6 +251,14 @@
 	pinctrl-0 = <&pinctrl_rgmii1_default>;
 };
 
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
 &fmc {
 	status = "okay";
 	flash at 0 {
@@ -439,6 +447,26 @@
 	status = "okay";
 };
 
+&i2c8 {
+	status = "okay";
+
+	pca9539 at 77 {
+		compatible = "nxp,pca9539";
+		reg = <0x77>;
+		gpio-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#gpio-cells = <2>;
+
+		bmc-ocp0-en-hog {
+			gpio-hog;
+			gpios = <7 GPIO_ACTIVE_LOW>;
+			output-high;
+			line-name = "bmc-ocp0-en-n";
+		};
+	};
+};
+
 &i2c9 {
 	status = "okay";
 };
@@ -530,13 +558,20 @@
 	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
 			"host0-reboot-ack-n","host0-ready","host0-shd-req-n",
 			"host0-shd-ack-n","s0-overtemp-n",
-	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
+	/*W0-W7*/	"","ocp-main-pwren","ocp-pgood","",
 			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
 	/*X0-X7*/	"i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
 			"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
 			"s1-overtemp-n","s1-spi-auth-fail-n",
 	/*Y0-Y7*/	"","","","","","","","host0-special-boot",
 	/*Z0-Z7*/	"reset-button","ps0-pgood","ps1-pgood","","","","","";
+
+	ocp-aux-pwren-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "ocp-aux-pwren";
+	};
 };
 
 &gpio1 {
-- 
2.17.1



More information about the Linux-aspeed mailing list