[PATCH 1/2] watchdog: aspeed: Add pre-timeout interrupt support
Guenter Roeck
linux at roeck-us.net
Sat Oct 22 15:00:22 AEDT 2022
On 10/21/22 12:39, Eddie James wrote:
>
> On 10/21/22 11:56, Guenter Roeck wrote:
>> On Fri, Oct 21, 2022 at 10:15:58AM -0500, Eddie James wrote:
>>> Enable the pre-timeout interrupt if requested by device property.
>>>
>> I am not inclined to accept this patch without detailed explanation.
>> Why would it make sense and/or be desirable to completely bypass the
>> watchdog core with this pretimeout support ?
>
>
> Sorry, I should add more detail.
>
> It doesn't necessarily bypass the watchdog core. It can, if you specify reset-type="none". But if not, the watchdog will still fire at the appropriate time.
>
> The purpose is to get a stack dump from a kernel panic rather than a hard reset from the watchdog. The interrupt will fire a certain number of microseconds (configurable by dts property) before the watchdog does. The interrupt handler then panics, and all the CPU stacks are dumped, so hopefully you can catch where another processor was stuck.
>
>
> I can submit v2 with this information in the commit message and/or comments.
>
You did not answer the question why you do not use the pretimeout functionality
supported by the watchdog core.
Guenter
> Thanks,
>
> Eddie
>
>
>>
>> Thanks,
>> Guenter
>>
>>> Signed-off-by: Eddie James <eajames at linux.ibm.com>
>>> ---
>>> drivers/watchdog/aspeed_wdt.c | 53 +++++++++++++++++++++++++++++++++--
>>> 1 file changed, 51 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/drivers/watchdog/aspeed_wdt.c b/drivers/watchdog/aspeed_wdt.c
>>> index 0cff2adfbfc9..8e12181a827e 100644
>>> --- a/drivers/watchdog/aspeed_wdt.c
>>> +++ b/drivers/watchdog/aspeed_wdt.c
>>> @@ -5,11 +5,14 @@
>>> * Joel Stanley <joel at jms.id.au>
>>> */
>>> +#include <linux/bits.h>
>>> #include <linux/delay.h>
>>> +#include <linux/interrupt.h>
>>> #include <linux/io.h>
>>> #include <linux/kernel.h>
>>> #include <linux/module.h>
>>> #include <linux/of.h>
>>> +#include <linux/of_irq.h>
>>> #include <linux/platform_device.h>
>>> #include <linux/watchdog.h>
>>> @@ -26,20 +29,32 @@ struct aspeed_wdt {
>>> struct aspeed_wdt_config {
>>> u32 ext_pulse_width_mask;
>>> + u32 irq_shift;
>>> + u32 irq_mask;
>>> };
>>> static const struct aspeed_wdt_config ast2400_config = {
>>> .ext_pulse_width_mask = 0xff,
>>> + .irq_shift = 0,
>>> + .irq_mask = 0,
>>> };
>>> static const struct aspeed_wdt_config ast2500_config = {
>>> .ext_pulse_width_mask = 0xfffff,
>>> + .irq_shift = 12,
>>> + .irq_mask = GENMASK(31, 12),
>>> +};
>>> +
>>> +static const struct aspeed_wdt_config ast2600_config = {
>>> + .ext_pulse_width_mask = 0xfffff,
>>> + .irq_shift = 0,
>>> + .irq_mask = GENMASK(31, 10),
>>> };
>>> static const struct of_device_id aspeed_wdt_of_table[] = {
>>> { .compatible = "aspeed,ast2400-wdt", .data = &ast2400_config },
>>> { .compatible = "aspeed,ast2500-wdt", .data = &ast2500_config },
>>> - { .compatible = "aspeed,ast2600-wdt", .data = &ast2500_config },
>>> + { .compatible = "aspeed,ast2600-wdt", .data = &ast2600_config },
>>> { },
>>> };
>>> MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table);
>>> @@ -58,6 +73,7 @@ MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table);
>>> #define WDT_CTRL_RESET_SYSTEM BIT(1)
>>> #define WDT_CTRL_ENABLE BIT(0)
>>> #define WDT_TIMEOUT_STATUS 0x10
>>> +#define WDT_TIMEOUT_STATUS_IRQ BIT(2)
>>> #define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1)
>>> #define WDT_CLEAR_TIMEOUT_STATUS 0x14
>>> #define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0)
>>> @@ -243,6 +259,17 @@ static const struct watchdog_info aspeed_wdt_info = {
>>> .identity = KBUILD_MODNAME,
>>> };
>>> +static irqreturn_t aspeed_wdt_irq(int irq, void *arg)
>>> +{
>>> + struct aspeed_wdt *wdt = arg;
>>> + u32 status = readl(wdt->base + WDT_TIMEOUT_STATUS);
>>> +
>>> + if (status & WDT_TIMEOUT_STATUS_IRQ)
>>> + panic("Watchdog pre-timeout IRQ");
>>> +
>>> + return IRQ_NONE;
>>> +}
>>> +
>>> static int aspeed_wdt_probe(struct platform_device *pdev)
>>> {
>>> struct device *dev = &pdev->dev;
>>> @@ -253,6 +280,7 @@ static int aspeed_wdt_probe(struct platform_device *pdev)
>>> const char *reset_type;
>>> u32 duration;
>>> u32 status;
>>> + u32 timeout = 0;
>>> int ret;
>>> wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
>>> @@ -291,6 +319,27 @@ static int aspeed_wdt_probe(struct platform_device *pdev)
>>> if (of_device_is_compatible(np, "aspeed,ast2400-wdt"))
>>> wdt->ctrl = WDT_CTRL_1MHZ_CLK;
>>> + if (config->irq_mask) {
>>> + if (!of_property_read_u32(np, "aspeed,pre-timeout-irq-us", &timeout) && timeout) {
>>> + int irq = platform_get_irq(pdev, 0);
>>> +
>>> + if (irq < 0) {
>>> + dev_warn(dev, "Couldn't find IRQ: %d\n", irq);
>>> + timeout = 0;
>>> + } else {
>>> + ret = devm_request_irq(dev, irq, aspeed_wdt_irq, IRQF_SHARED,
>>> + dev_name(dev), wdt);
>>> + if (ret) {
>>> + dev_warn(dev, "Couldn't request IRQ:%d\n", ret);
>>> + timeout = 0;
>>> + } else {
>>> + wdt->ctrl |= ((timeout << config->irq_shift) &
>>> + config->irq_mask) | WDT_CTRL_WDT_INTR;
>>> + }
>>> + }
>>> + }
>>> + }
>>> +
>>> /*
>>> * Control reset on a per-device basis to ensure the
>>> * host is not affected by a BMC reboot
>>> @@ -308,7 +357,7 @@ static int aspeed_wdt_probe(struct platform_device *pdev)
>>> else if (!strcmp(reset_type, "system"))
>>> wdt->ctrl |= WDT_CTRL_RESET_MODE_FULL_CHIP |
>>> WDT_CTRL_RESET_SYSTEM;
>>> - else if (strcmp(reset_type, "none"))
>>> + else if (strcmp(reset_type, "none") && !timeout)
>>> return -EINVAL;
>>> }
>>> if (of_property_read_bool(np, "aspeed,external-signal"))
>>> --
>>> 2.31.1
>>>
More information about the Linux-aspeed
mailing list