[PATCH] ARM: dts: aspeed: Add ASRock X570D4U BMC
Joel Stanley
joel at jms.id.au
Mon Nov 7 15:13:24 AEDT 2022
On Sun, 6 Nov 2022 at 22:42, Renze Nicolai <renze at rnplus.nl> wrote:
>
> This is a relatively low-cost AST2500-based Amd Ryzen 5000 Series
> micro-ATX board that we hope can provide a decent platform for OpenBMC
> development.
>
> This initial device-tree provides the necessary configuration for
> basic BMC functionality such as serial console, KVM support
> and POST code snooping.
Cool!
>
> Signed-off-by: Renze Nicolai <renze at rnplus.nl>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> .../boot/dts/aspeed-bmc-asrock-x570d4u.dts | 360 ++++++++++++++++++
> 2 files changed, 361 insertions(+)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-asrock-x570d4u.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 6aa7dc4db2fc..adbbf27dfcee 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1587,6 +1587,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-arm-stardragon4800-rep2.dtb \
> aspeed-bmc-asrock-e3c246d4i.dtb \
> aspeed-bmc-asrock-romed8hm3.dtb \
> + aspeed-bmc-asrock-x570d4u.dtb \
> aspeed-bmc-bytedance-g220a.dtb \
> aspeed-bmc-facebook-bletchley.dtb \
> aspeed-bmc-facebook-cloudripper.dtb \
> diff --git a/arch/arm/boot/dts/aspeed-bmc-asrock-x570d4u.dts
> b/arch/arm/boot/dts/aspeed-bmc-asrock-x570d4u.dts
> new file mode 100644
> index 000000000000..818c8879e0a0
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-asrock-x570d4u.dts
> @@ -0,0 +1,360 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +// Copyright (c) 2022 Renze Nicolai <renze at rnplus.nl>
> +
> +/dts-v1/;
> +#include "aspeed-g5.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> + model = "Asrock Rack X570D4U BMC";
> + compatible = "asrock,x570d4u-bmc";
> +
> + chosen {
> + stdout-path = &uart5;
> + bootargs = "console=ttyS4,115200 earlycon";
> + };
> +
> + memory at 80000000 {
> + reg = <0x80000000 0x20000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + flash_memory: region at 98000000 {
> + no-map;
> + reg = <0x98000000 0x04000000>; /* 64M */
> + };
Do you need this? Normally it's used for loading the host firmware
from DRAM instead of SPI flash on OpenPower machines.
> +
> + vga_memory: framebuffer at 9f000000 {
> + no-map;
> + reg = <0x9f000000 0x01000000>; /* 16M */
> + };
The VGA device is for the BMC driving the display. If you're only
interested in the host processor driving the display you don't need to
enable this.
> +
> + pci_memory: region at 9A000000 {
> + no-map;
> + reg = <0x9A000000 0x00010000>; /* 64K */
> + };
> +
> + video_engine_memory: jpegbuffer {
> + size = <0x02800000>; /* 40M */
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> +
> + gfx_memory: framebuffer {
> + size = <0x01000000>;
> + alignment = <0x01000000>;
> + compatible = "shared-dma-pool";
> + reusable;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + heartbeat {
> + /* BMC_HB_LED_N */
> + gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "timer";
> + };
> +
> + system-fault {
> + /* SYSTEM_FAULT_LED_N */
> + gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
> + panic-indicator;
> + };
> + };
> +
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
> + <&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>,
> + <&adc 10>, <&adc 11>, <&adc 12>;
> + };
> +};
> +
> +&gpio {
> + status = "okay";
> + gpio-line-names =
Are you familiar with this one?
https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md
If you can use any of the common names that would be preferred.
> + /*A0-A3*/ "LOCATORLED_STATUS_N", "",
> "NMI_BTN_N", "BMC_NMI",
> + /*A4-A7*/ "", "", "",
> "",
> + /*B0-B3*/ "FM_BIOS_POST_CMPLT_N", "", "",
> "",
> + /*B4-B7*/ "", "IRQ_BMC_PCH_SMI_LPC_N","",
> "",
> + /*C0-C3*/ "", "", "",
> "",
> + /*C4-C7*/ "", "",
> "LOCATORBTN", "",
> + /*D0-D3*/ "BMC_PSIN", "BMC_PSOUT",
> "BMC_RESETCON", "RESETCON",
> + /*D4-D7*/ "", "", "",
> "",
> + /*E0-E3*/ "", "", "",
> "",
> + /*E4-E7*/ "", "", "",
> "",
> + /*F0-F3*/ "", "", "",
> "",
> + /*F4-F7*/ "", "", "",
> "",
> + /*G0-G3*/ "HWM_BAT_EN", "CHASSIS_ID0",
> "CHASSIS_ID1", "CHASSIS_ID2",
> + /*G4-G7*/ "BMC_ALERT1_N_R", "BMC_ALERT2_N_R",
> "BMC_ALERT3_N", "SML0ALERT",
> + /*H0-H3*/ "", "O_PWROK", "",
> "",
> + /*H4-H7*/ "MFG_MODE_N", "BMC_RTCRST",
> "BMC_HB_LED_N", "BMC_CASEOPEN",
> + /*I0-I3*/ "", "", "",
> "",
> + /*I4-I7*/ "", "", "",
> "",
> + /*J0-J3*/ "BMC_READY", "", "",
> "",
> + /*J4-J7*/ "VGAHS", "VGAVS",
> "DDCCLK", "DDCDAT",
> + /*K0-K3*/ "I2C_SCL4", "I2C_SDA4",
> "I2C_SCL5", "I2C_SDA5",
> + /*K4-K7*/ "", "",
> "I2C_SCL7", "I2C_SDA7",
> + /*L0-L3*/ "BMC_CTS1", "BMC_DCD1",
> "BMC_DSR1", "BMC_RI1",
> + /*L4-L7*/ "BMC_DTR1", "BMC_RTS1",
> "BMC_TXD1", "BMC_RXD1",
> + /*M0-M3*/ "BMC_LAN0_DIS_N", "BMC_LAN1_DIS_N", "",
> "",
> + /*M4-M7*/ "", "", "",
> "",
> + /*N0-N3*/ "PWM_FAN1", "PWM_FAN2",
> "PWM_FAN3", "PWM_FAN4",
> + /*N4-N7*/ "PWM_FAN6", "PWM_FAN5", "",
> "",
> + /*O0-O3*/ "TACHO_FAN1", "TACHO_FAN2",
> "TACHO_FAN3", "TACHO_FAN4",
> + /*O4-O7*/ "TACHO_FAN5", "TACHO_FAN6", "",
> "",
> + /*P0-P3*/ "", "", "",
> "PS_PWROK",
> + /*P4-P7*/ "", "", "",
> "",
> + /*Q0-Q3*/ "I2C_SCL2", "I2C_SDA2",
> "I2C_SCL3", "I2C_SDA3",
> + /*Q4-Q7*/ "BMC_SBM_PRESENT_1_N", "BMC_SBM_PRESENT_2_N",
> "BMC_SBM_PRESENT_3_N","BMC_PCIE_WAKE_N",
> + /*R0-R3*/ "", "", "",
> "",
> + /*R4-R7*/ "", "", "",
> "",
> + /*S0-S3*/ "PCHHOT_BMC_N", "",
> "RSMRST", "",
> + /*S4-S7*/ "", "", "",
> "",
> + /*T0-T3*/ "RGMII1TXCK", "RGMII1TXCL",
> "RGMII1TXD0", "RGMII1TXD1",
> + /*T4-T7*/ "RGMII1TXD2", "RGMII1TXD3",
> "RMII2RCLKO", "RMII2TXEN",
> + /*U0-U3*/ "RMII2TXD0", "RMII2TXD1", "",
> "",
> + /*U4-U7*/ "RGMII1RXCK", "RGMII1RXCTL",
> "RGMII1RXD0", "RGMII1RXD1",
> + /*V0-V3*/ "RGMII1RXD2", "RGMII1RXD3",
> "RMII2RCLKI", "",
> + /*V4-V7*/ "RMII2RXD0", "RMII2RXD1",
> "RMII2CRSDV", "RMII2RXER",
> + /*W0-W3*/ "", "", "",
> "",
> + /*W4-W7*/ "", "", "",
> "",
> + /*X0-X3*/ "", "", "",
> "",
> + /*X4-X7*/ "", "", "",
> "",
> + /*Y0-Y3*/ "SLP_S3", "SLP_S5", "",
> "",
> + /*Y4-Y7*/ "I2C_SCL0", "I2C_SDA0",
> "I2C_SCL1", "I2C_SDA1",
> + /*Z0-Z3*/ "", "",
> "SYSTEM_FAULT_LED_N", "BMC_THROTTLE_N",
> + /*Z4-Z7*/ "", "", "",
> "",
> + /*AA0-AA3*/ "CPU1_THERMTRIP_LATCH_N", "",
> "CPU1_PROCHOT_N", "",
> + /*AA4-AC7*/ "", "", "",
> "",
> + /*AB0-AB3*/ "", "", "",
> "",
> + /*AB4-AC7*/ "", "", "",
> "",
> + /*AC0-AC3*/ "LAD0", "LAD1",
> "LAD2", "LAD3",
> + /*AC4-AC7*/ "CK_33M_BMC", "LFRAME",
> "SERIRQ", "S_PLTRST";
> +
> +
> + /* Assert BMC_READY so BIOS doesn't sit around waiting for it */
> + bmc-ready {
> + gpio-hog;
> + gpios = <ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
> + output-high;
> + };
> +};
> +
> +&fmc {
> + status = "okay";
> + flash at 0 {
> + status = "okay";
> + label = "bmc";
> + m25p,fast-read;
> + spi-max-frequency = <10000000>;
> +#include "openbmc-flash-layout-64.dtsi"
> + };
> +};
> +
> +&uart5 {
> + status = "okay";
> +};
> +
> +&vuart {
> + status = "okay";
> +};
> +
> +&mac0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
> +};
> +
> +&mac1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rmii2_default &pinctrl_mdio2_default>;
> + use-ncsi;
mdio and ncsi are mutually exclusive. If this port is connected via
NCSI, you want to do this:
&mac0 {
status = "okay";
use-ncsi;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_rmii1_default>;
clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>,
<&syscon ASPEED_CLK_MAC1RCLK>;
clock-names = "MACCLK", "RCLK";
};
(I can't recall if everyone needs to enable RCLK or if that's specific
to the openpower designs)
> +};
> +
> +&i2c0 {
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +
> + w83773g at 4c {
> + compatible = "nuvoton,w83773g";
> + reg = <0x4c>;
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + status = "okay";
> +};
> +
> +&i2c4 {
> + status = "okay";
> +
> + i2c-switch at 70 {
> + compatible = "nxp,pca9545";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x70>;
> +
> + interrupt-parent = <&i2c_ic>;
> + interrupts = <4>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + i2c at 0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + };
> +
> + i2c at 1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + };
> +
> + i2c at 2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> + };
> +
> + i2c at 3 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <3>;
> + };
> + };
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2c7 {
> + status = "okay";
> +
> + eeprom at 57 {
> + compatible = "st,24c128", "atmel,24c128";
> + reg = <0x57>;
> + pagesize = <16>;
> + };
> +};
> +
> +&gfx {
> + status = "okay";
> +};
You've got GFX twice, see below.
> +
> +&pinctrl {
> + aspeed,external-nodes = <&gfx &lhc>;
> +};
> +
> +&vhub {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +&uhci {
> + status = "okay";
> +};
> +
> +&kcs3 {
> + aspeed,lpc-io-reg = <0xca2>;
> + status = "okay";
> +};
> +
> +&lpc_ctrl {
> + status = "okay";
> +};
> +
> +&lpc_snoop {
> + status = "okay";
> + snoop-ports = <0x80>;
> +};
> +
> +&p2a {
> + status = "okay";
> + memory-region = <&pci_memory>;
> +};
> +
> +&video {
> + status = "okay";
> + memory-region = <&video_engine_memory>;
> +};
> +
> +&gfx {
> + status = "okay";
> + memory-region = <&gfx_memory>;
> +};
> +
> +&pwm_tacho {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm0_default
> + &pinctrl_pwm1_default
> + &pinctrl_pwm2_default
> + &pinctrl_pwm3_default
> + &pinctrl_pwm4_default
> + &pinctrl_pwm5_default>;
> + fan at 0 {
> + reg = <0x00>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x00 0x01>;
> + };
> + fan at 1 {
> + reg = <0x01>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x02 0x03>;
> + };
> + fan at 2 {
> + reg = <0x02>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x04 0x05>;
> + };
> + fan at 3 {
> + reg = <0x03>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x06 0x07>;
> + };
> + fan at 4 {
> + reg = <0x04>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x08 0x09>;
> + };
> + fan at 5 {
> + reg = <0x05>;
> + aspeed,fan-tach-ch = /bits/ 8 <0x0a 0x0b>;
> + };
> +};
> +
> +&adc {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_adc0_default
> + &pinctrl_adc1_default
> + &pinctrl_adc2_default
> + &pinctrl_adc3_default
> + &pinctrl_adc4_default
> + &pinctrl_adc5_default
> + &pinctrl_adc6_default
> + &pinctrl_adc7_default
> + &pinctrl_adc8_default
> + &pinctrl_adc9_default
> + &pinctrl_adc10_default
> + &pinctrl_adc11_default
> + &pinctrl_adc12_default
> + &pinctrl_adc13_default
> + &pinctrl_adc14_default
> + &pinctrl_adc15_default>;
> +};
> --
> 2.38.1
More information about the Linux-aspeed
mailing list