[PATCH v2 3/4] media: aspeed: Correct values for detected timing

Hans Verkuil hverkuil at xs4all.nl
Fri Jan 21 18:28:41 AEDT 2022


Hi Jammy,

On 1/21/22 07:01, Jammy Huang wrote:
> Hi Hans,
> 
> Yes, this is a weird part of our hardware.
> Because it uses the rising edge of the sync to start counting, an additional calculation
> is needed to get the exact value of the timings.
> 
> This problem was found when I was debugging the timing detection unstable problem.

OK, thank you for the confirmation.

I would like a v3 where basically the explanation you made in the cover letter
is copied to the code, probably as a comment block just before aspeed_video_get_resolution().

This is unusual enough that it should be documented well in the code.

Regards,

	Hans

> 
> Reards,
> 
> Jammy
> 
> On 2022/1/20 下午 08:31, Hans Verkuil wrote:
>> Hi Jammy,
>>
>> I just want to double check this: I assume you have tested this with the
>> various polarity combinations?
>>
>> I ask because I've never seen this before in any other hardware. The
>> sync and porch values reported by hardware are always independent from the
>> polarity, so that's why I am surprised to see this.
>>
>> Same for the next patch (4/4).
>>
>> Regards,
>>
>>     Hans
>>
>> On 12/22/21 09:21, Jammy Huang wrote:
>>> Correct timing's fp/sync/bp value based on the information below.
>>> It should be noticed that the calculation formula should be changed
>>> per sync polarity.
>>>
>>> The sequence of signal: sync - backporch - video data - frontporch
>>>
>>> The following registers start counting from sync's rising edge:
>>> 1. VR090: frame edge's left and right
>>> 2. VR094: frame edge's top and bottom
>>> 3. VR09C: counting from sync's rising edge to falling edge
>>>
>>> [Vertical timing]
>>>              +--+     +-------------------+     +--+
>>>              |  |     |    v i d e o      |     |  |
>>>           +--+  +-----+                   +-----+  +---+
>>>
>>>         vsync+--+
>>>     frame_top+--------+
>>> frame_bottom+----------------------------+
>>>
>>>                    +-------------------+
>>>                    |    v i d e o      |
>>>        +--+  +-----+                   +-----+  +---+
>>>           |  |                               |  |
>>>           +--+                               +--+
>>>         vsync+-------------------------------+
>>>     frame_top+-----+
>>> frame_bottom+-------------------------+
>>>
>>> [Horizontal timing]
>>>              +--+     +-------------------+     +--+
>>>              |  |     |    v i d e o      |     |  |
>>>           +--+  +-----+                   +-----+  +---+
>>>
>>>         hsync+--+
>>>    frame_left+--------+
>>>   frame_right+----------------------------+
>>>
>>>                    +-------------------+
>>>                    |    v i d e o      |
>>>        +--+  +-----+                   +-----+  +---+
>>>           |  |                               |  |
>>>           +--+                               +--+
>>>         hsync+-------------------------------+
>>>    frame_left+-----+
>>>   frame_right+-------------------------+
>>>
>>> Signed-off-by: Jammy Huang <jammy_huang at aspeedtech.com>
>>> ---
>>>   v2:
>>>    - Code refined per Joel's suggestion
>>>    - Update commit message to have name matching variable
>>> ---
>>>   drivers/media/platform/aspeed-video.c | 30 ++++++++++++++++++++-------
>>>   1 file changed, 22 insertions(+), 8 deletions(-)
>>>
>>> diff --git a/drivers/media/platform/aspeed-video.c b/drivers/media/platform/aspeed-video.c
>>> index c241038ee27c..7c50567f5ab0 100644
>>> --- a/drivers/media/platform/aspeed-video.c
>>> +++ b/drivers/media/platform/aspeed-video.c
>>> @@ -936,7 +936,7 @@ static void aspeed_video_get_resolution(struct aspeed_video *video)
>>>       u32 src_lr_edge;
>>>       u32 src_tb_edge;
>>>       u32 sync;
>>> -    u32 htotal;
>>> +    u32 htotal, vtotal, vsync, hsync;
>>>       struct v4l2_bt_timings *det = &video->detected_timings;
>>>         det->width = MIN_WIDTH;
>>> @@ -983,21 +983,35 @@ static void aspeed_video_get_resolution(struct aspeed_video *video)
>>>           mds = aspeed_video_read(video, VE_MODE_DETECT_STATUS);
>>>           sync = aspeed_video_read(video, VE_SYNC_STATUS);
>>>           htotal = aspeed_video_read(video, VE_H_TOTAL_PIXELS);
>>> +        vtotal = FIELD_GET(VE_MODE_DETECT_V_LINES, mds);
>>> +        vsync = FIELD_GET(VE_SYNC_STATUS_VSYNC, sync);
>>> +        hsync = FIELD_GET(VE_SYNC_STATUS_HSYNC, sync);
>>>             video->frame_bottom = FIELD_GET(VE_SRC_TB_EDGE_DET_BOT, src_tb_edge);
>>>           video->frame_top = FIELD_GET(VE_SRC_TB_EDGE_DET_TOP, src_tb_edge);
>>> -        det->vfrontporch = video->frame_top;
>>> -        det->vbackporch = FIELD_GET(VE_MODE_DETECT_V_LINES, mds) -
>>> -            video->frame_bottom;
>>> -        det->vsync = FIELD_GET(VE_SYNC_STATUS_VSYNC, sync);
>>> +        if (det->polarities & V4L2_DV_VSYNC_POS_POL) {
>>> +            det->vbackporch = video->frame_top - vsync;
>>> +            det->vfrontporch = vtotal - video->frame_bottom;
>>> +            det->vsync = vsync;
>>> +        } else {
>>> +            det->vbackporch = video->frame_top;
>>> +            det->vfrontporch = vsync - video->frame_bottom;
>>> +            det->vsync = vtotal - vsync;
>>> +        }
>>>           if (video->frame_top > video->frame_bottom)
>>>               continue;
>>>             video->frame_right = FIELD_GET(VE_SRC_LR_EDGE_DET_RT, src_lr_edge);
>>>           video->frame_left = FIELD_GET(VE_SRC_LR_EDGE_DET_LEFT, src_lr_edge);
>>> -        det->hfrontporch = video->frame_left;
>>> -        det->hbackporch = htotal - video->frame_right;
>>> -        det->hsync = FIELD_GET(VE_SYNC_STATUS_HSYNC, sync);
>>> +        if (det->polarities & V4L2_DV_HSYNC_POS_POL) {
>>> +            det->hbackporch = video->frame_left - hsync;
>>> +            det->hfrontporch = htotal - video->frame_right;
>>> +            det->hsync = hsync;
>>> +        } else {
>>> +            det->hbackporch = video->frame_left;
>>> +            det->hfrontporch = hsync - video->frame_right;
>>> +            det->hsync = htotal - hsync;
>>> +        }
>>>           if (video->frame_left > video->frame_right)
>>>               continue;
>>>   


More information about the Linux-aspeed mailing list