Re: [PATCH v3 14/16] ipmi: kcs_bmc_aspeed: Implement KCS SerIRQ configuration
Andrew Jeffery
andrew at aj.id.au
Tue Jun 8 10:55:04 AEST 2021
On Tue, 8 Jun 2021, at 10:11, Andrew Jeffery wrote:
>
>
> On Fri, 21 May 2021, at 16:51, Zev Weiss wrote:
> > On Mon, May 10, 2021 at 12:42:11AM CDT, Andrew Jeffery wrote:
> > >Apply the SerIRQ ID and level/sense behaviours from the devicetree if
> > >provided.
> > >
> > >Signed-off-by: Andrew Jeffery <andrew at aj.id.au>
> > >---
> > > drivers/char/ipmi/kcs_bmc_aspeed.c | 182 ++++++++++++++++++++++++++++-
> > > 1 file changed, 180 insertions(+), 2 deletions(-)
> > >
> > >diff --git a/drivers/char/ipmi/kcs_bmc_aspeed.c b/drivers/char/ipmi/kcs_bmc_aspeed.c
> > >index 8a0b1e18e945..9b81806b4dcb 100644
> > >--- a/drivers/char/ipmi/kcs_bmc_aspeed.c
> > >+++ b/drivers/char/ipmi/kcs_bmc_aspeed.c
> > >@@ -9,6 +9,7 @@
> > > #include <linux/errno.h>
> > > #include <linux/interrupt.h>
> > > #include <linux/io.h>
> > >+#include <linux/irq.h>
> > > #include <linux/mfd/syscon.h>
> > > #include <linux/module.h>
> > > #include <linux/of.h>
> > >@@ -28,6 +29,22 @@
> > >
> > > #define KCS_CHANNEL_MAX 4
> > >
> > >+/*
> > >+ * Field class descriptions
> > >+ *
> > >+ * LPCyE Enable LPC channel y
> > >+ * IBFIEy Input Buffer Full IRQ Enable for LPC channel y
> > >+ * IRQxEy Assert SerIRQ x for LPC channel y (Deprecated, use IDyIRQX, IRQXEy)
> > >+ * IDyIRQX Use the specified 4-bit SerIRQ for LPC channel y
> > >+ * SELyIRQX SerIRQ polarity for LPC channel y (low: 0, high: 1)
> > >+ * IRQXEy Assert the SerIRQ specified in IDyIRQX for LPC channel y
> > >+ */
> > >+
> > >+#define LPC_TYIRQX_LOW 0b00
> > >+#define LPC_TYIRQX_HIGH 0b01
> > >+#define LPC_TYIRQX_RSVD 0b10
> > >+#define LPC_TYIRQX_RISING 0b11
> > >+
> > > #define LPC_HICR0 0x000
> > > #define LPC_HICR0_LPC3E BIT(7)
> > > #define LPC_HICR0_LPC2E BIT(6)
> > >@@ -39,6 +56,19 @@
> > > #define LPC_HICR4 0x010
> > > #define LPC_HICR4_LADR12AS BIT(7)
> > > #define LPC_HICR4_KCSENBL BIT(2)
> > >+#define LPC_SIRQCR0 0x070
> > >+/* IRQ{12,1}E1 are deprecated as of AST2600 A3 but necessary for prior chips */
> > >+#define LPC_SIRQCR0_IRQ12E1 BIT(1)
> > >+#define LPC_SIRQCR0_IRQ1E1 BIT(0)
> > >+#define LPC_HICR5 0x080
> > >+#define LPC_HICR5_ID3IRQX_MASK GENMASK(23, 20)
> > >+#define LPC_HICR5_ID3IRQX_SHIFT 20
> > >+#define LPC_HICR5_ID2IRQX_MASK GENMASK(19, 16)
> > >+#define LPC_HICR5_ID2IRQX_SHIFT 16
> > >+#define LPC_HICR5_SEL3IRQX BIT(15)
> > >+#define LPC_HICR5_IRQXE3 BIT(14)
> > >+#define LPC_HICR5_SEL2IRQX BIT(13)
> > >+#define LPC_HICR5_IRQXE2 BIT(12)
> > > #define LPC_LADR3H 0x014
> > > #define LPC_LADR3L 0x018
> > > #define LPC_LADR12H 0x01C
> > >@@ -55,6 +85,13 @@
> > > #define LPC_HICRB 0x100
> > > #define LPC_HICRB_IBFIF4 BIT(1)
> > > #define LPC_HICRB_LPC4E BIT(0)
> > >+#define LPC_HICRC 0x104
> > >+#define LPC_HICRC_ID4IRQX_MASK GENMASK(7, 4)
> > >+#define LPC_HICRC_ID4IRQX_SHIFT 4
> > >+#define LPC_HICRC_TY4IRQX_MASK GENMASK(3, 2)
> > >+#define LPC_HICRC_TY4IRQX_SHIFT 2
> > >+#define LPC_HICRC_OBF4_AUTO_CLR BIT(1)
> > >+#define LPC_HICRC_IRQXE4 BIT(0)
> > > #define LPC_LADR4 0x110
> > > #define LPC_IDR4 0x114
> > > #define LPC_ODR4 0x118
> > >@@ -62,11 +99,21 @@
> > >
> > > #define OBE_POLL_PERIOD (HZ / 2)
> > >
> > >+enum aspeed_kcs_irq_mode {
> > >+ aspeed_kcs_irq_none,
> > >+ aspeed_kcs_irq_serirq,
> > >+};
> > >+
> > > struct aspeed_kcs_bmc {
> > > struct kcs_bmc_device kcs_bmc;
> > >
> > > struct regmap *map;
> > >
> > >+ struct {
> > >+ enum aspeed_kcs_irq_mode mode;
> > >+ int id;
> > >+ } upstream_irq;
> > >+
> > > struct {
> > > spinlock_t lock;
> > > bool remove;
> > >@@ -103,6 +150,49 @@ static void aspeed_kcs_outb(struct kcs_bmc_device *kcs_bmc, u32 reg, u8 data)
> > >
> > > rc = regmap_write(priv->map, reg, data);
> > > WARN(rc != 0, "regmap_write() failed: %d\n", rc);
> > >+
> > >+ /* Trigger the upstream IRQ on ODR writes, if enabled */
> > >+
> > >+ switch (reg) {
> > >+ case LPC_ODR1:
> > >+ case LPC_ODR2:
> > >+ case LPC_ODR3:
> > >+ case LPC_ODR4:
> > >+ break;
> > >+ default:
> > >+ return;
> > >+ }
> > >+
> > >+ if (priv->upstream_irq.mode != aspeed_kcs_irq_serirq)
> > >+ return;
> > >+
> > >+ switch (kcs_bmc->channel) {
> > >+ case 1:
> > >+ switch (priv->upstream_irq.id) {
> > >+ case 12:
> > >+ regmap_update_bits(priv->map, LPC_SIRQCR0, LPC_SIRQCR0_IRQ12E1,
> > >+ LPC_SIRQCR0_IRQ12E1);
> > >+ break;
> > >+ case 1:
> > >+ regmap_update_bits(priv->map, LPC_SIRQCR0, LPC_SIRQCR0_IRQ1E1,
> > >+ LPC_SIRQCR0_IRQ1E1);
> > >+ break;
This is the code supporting the comment below.
> > >+ default:
> > >+ break;
> > >+ }
> > >+ break;
> > >+ case 2:
> > >+ regmap_update_bits(priv->map, LPC_HICR5, LPC_HICR5_IRQXE2, LPC_HICR5_IRQXE2);
> > >+ break;
> > >+ case 3:
> > >+ regmap_update_bits(priv->map, LPC_HICR5, LPC_HICR5_IRQXE3, LPC_HICR5_IRQXE3);
> > >+ break;
> > >+ case 4:
> > >+ regmap_update_bits(priv->map, LPC_HICRC, LPC_HICRC_IRQXE4, LPC_HICRC_IRQXE4);
> > >+ break;
> > >+ default:
> > >+ break;
> > >+ }
> > > }
> > >
> > > static void aspeed_kcs_updateb(struct kcs_bmc_device *kcs_bmc, u32 reg, u8 mask, u8 val)
> > >@@ -161,6 +251,73 @@ static void aspeed_kcs_set_address(struct kcs_bmc_device *kcs_bmc, u16 addr)
> > > }
> > > }
> > >
> > >+static inline int aspeed_kcs_map_serirq_type(u32 dt_type)
> > >+{
> > >+ switch (dt_type) {
> > >+ case IRQ_TYPE_EDGE_RISING:
> > >+ return LPC_TYIRQX_RISING;
> > >+ case IRQ_TYPE_LEVEL_HIGH:
> > >+ return LPC_TYIRQX_HIGH;
> > >+ case IRQ_TYPE_LEVEL_LOW:
> > >+ return LPC_TYIRQX_LOW;
> > >+ default:
> > >+ return -EINVAL;
> > >+ }
> > >+}
> > >+
> > >+static int aspeed_kcs_config_upstream_irq(struct aspeed_kcs_bmc *priv, u32 id, u32 dt_type)
> > >+{
> > >+ unsigned int mask, val, hw_type;
> > >+
> > >+ if (id > 15)
> > >+ return -EINVAL;
> > >+
> > >+ hw_type = aspeed_kcs_map_serirq_type(dt_type);
> > >+ if (hw_type < 0)
> > >+ return hw_type;
> > >+
> > >+ priv->upstream_irq.mode = aspeed_kcs_irq_serirq;
> > >+ priv->upstream_irq.id = id;
> > >+
> > >+ switch (priv->kcs_bmc.channel) {
> > >+ case 1:
> > >+ /* Needs IRQxE1 rather than (ID1IRQX, SEL1IRQX, IRQXE1) before AST2600 A3 */
> >
> > I'm struggling a bit with understanding this comment, and relating it to
> > the code -- it sounds like "we need to do things one way on A3 and
> > later, and another way on pre-A3", but then...we just break without
> > doing anything at all either way. Can you clarify any further?
>
> Hah! You're struggling because it doesn't make any sense, the code's
> gone missing :/ I'll fix that up.
Wait, no, this is fine. I just refreshed my memory on what's happening here. This function just configures the SerIRQ - in the case of channel 1 no configuration is necessary as it only has a fixed set of IRQs that we can associate with it. To enable one of them, we just set the appropriate bit in aspeed_kcs_outb() above.
Andrew
More information about the Linux-aspeed
mailing list