[PATCH v2 1/4] dt-bindings: i2c: aspeed: add buffer and DMA mode transfer support
Jae Hyun Yoo
jae.hyun.yoo at linux.intel.com
Tue Jan 12 11:37:46 AEDT 2021
Append bindings to support buffer mode and DMA mode transfer.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo at linux.intel.com>
---
Changes since v1:
- Removed buffer reg settings from default device tree and added the settings
into here to show the predefined buffer range per each bus.
.../devicetree/bindings/i2c/i2c-aspeed.txt | 126 +++++++++++++++++-
1 file changed, 119 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
index b47f6ccb196a..978e8402fdfc 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
@@ -3,7 +3,62 @@ Device tree configuration for the I2C busses on the AST24XX, AST25XX, and AST26X
Required Properties:
- #address-cells : should be 1
- #size-cells : should be 0
-- reg : address offset and range of bus
+- reg : Address offset and range of bus registers.
+
+ An additional SRAM buffer address offset and range is
+ optional in case of enabling I2C dedicated SRAM for
+ buffer mode transfer support. If the optional range
+ is defined, buffer mode will be enabled.
+ - AST2400
+ &i2c0 { reg = <0x40 0x40>, <0x800 0x80>; };
+ &i2c1 { reg = <0x80 0x40>, <0x880 0x80>; };
+ &i2c2 { reg = <0xc0 0x40>, <0x900 0x80>; };
+ &i2c3 { reg = <0x100 0x40>, <0x980 0x80>; };
+ &i2c4 { reg = <0x140 0x40>, <0xa00 0x80>; };
+ &i2c5 { reg = <0x180 0x40>, <0xa80 0x80>; };
+ &i2c6 { reg = <0x1c0 0x40>, <0xb00 0x80>; };
+ &i2c7 { reg = <0x300 0x40>, <0xb80 0x80>; };
+ &i2c8 { reg = <0x340 0x40>, <0xc00 0x80>; };
+ &i2c9 { reg = <0x380 0x40>, <0xc80 0x80>; };
+ &i2c10 { reg = <0x3c0 0x40>, <0xd00 0x80>; };
+ &i2c11 { reg = <0x400 0x40>, <0xd80 0x80>; };
+ &i2c12 { reg = <0x440 0x40>, <0xe00 0x80>; };
+ &i2c13 { reg = <0x480 0x40>, <0xe80 0x80>; };
+
+ - AST2500
+ &i2c0 { reg = <0x40 0x40>, <0x200 0x10>; };
+ &i2c1 { reg = <0x80 0x40>, <0x210 0x10>; };
+ &i2c2 { reg = <0xc0 0x40>, <0x220 0x10>; };
+ &i2c3 { reg = <0x100 0x40>, <0x230 0x10>; };
+ &i2c4 { reg = <0x140 0x40>, <0x240 0x10>; };
+ &i2c5 { reg = <0x180 0x40>, <0x250 0x10>; };
+ &i2c6 { reg = <0x1c0 0x40>, <0x260 0x10>; };
+ &i2c7 { reg = <0x300 0x40>, <0x270 0x10>; };
+ &i2c8 { reg = <0x340 0x40>, <0x280 0x10>; };
+ &i2c9 { reg = <0x380 0x40>, <0x290 0x10>; };
+ &i2c10 { reg = <0x3c0 0x40>, <0x2a0 0x10>; };
+ &i2c11 { reg = <0x400 0x40>, <0x2b0 0x10>; };
+ &i2c12 { reg = <0x440 0x40>, <0x2c0 0x10>; };
+ &i2c13 { reg = <0x480 0x40>, <0x2d0 0x10>; };
+
+ - AST2600
+ &i2c0 { reg = <0x80 0x80>, <0xc00 0x20>; };
+ &i2c1 { reg = <0x100 0x80>, <0xc20 0x20>; };
+ &i2c2 { reg = <0x180 0x80>, <0xc40 0x20>; };
+ &i2c3 { reg = <0x200 0x80>, <0xc60 0x20>; };
+ &i2c4 { reg = <0x280 0x80>, <0xc80 0x20>; };
+ &i2c5 { reg = <0x300 0x80>, <0xca0 0x20>; };
+ &i2c6 { reg = <0x380 0x80>, <0xcc0 0x20>; };
+ &i2c7 { reg = <0x400 0x80>, <0xce0 0x20>; };
+ &i2c8 { reg = <0x480 0x80>, <0xd00 0x20>; };
+ &i2c9 { reg = <0x500 0x80>, <0xd20 0x20>; };
+ &i2c10 { reg = <0x580 0x80>, <0xd40 0x20>; };
+ &i2c11 { reg = <0x600 0x80>, <0xd60 0x20>; };
+ &i2c12 { reg = <0x680 0x80>, <0xd80 0x20>; };
+ &i2c13 { reg = <0x700 0x80>, <0xda0 0x20>; };
+ &i2c14 { reg = <0x780 0x80>, <0xdc0 0x20>; };
+ &i2c15 { reg = <0x800 0x80>, <0xde0 0x20>; };
+
- compatible : should be "aspeed,ast2400-i2c-bus"
or "aspeed,ast2500-i2c-bus"
or "aspeed,ast2600-i2c-bus"
@@ -17,6 +72,25 @@ Optional Properties:
- bus-frequency : frequency of the bus clock in Hz defaults to 100 kHz when not
specified
- multi-master : states that there is another master active on this bus.
+- aspeed,dma-buf-size : size of DMA buffer.
+ AST2400: N/A
+ AST2500: 2 ~ 4095
+ AST2600: 2 ~ 4096
+
+ If both DMA and buffer modes are enabled in device
+ tree, DMA mode will be selected.
+
+ AST2500 has these restrictions:
+ - If one of these controllers is enabled
+ * UHCI host controller
+ * MCTP controller
+ I2C has to use buffer mode or byte mode instead
+ since these controllers run only in DMA mode and
+ I2C is sharing the same DMA H/W with them.
+ - If one of these controllers uses DMA mode, I2C
+ can't use DMA mode
+ * SD/eMMC
+ * Port80 snoop
Example:
@@ -26,12 +100,21 @@ i2c {
#size-cells = <1>;
ranges = <0 0x1e78a000 0x1000>;
- i2c_ic: interrupt-controller at 0 {
- #interrupt-cells = <1>;
- compatible = "aspeed,ast2400-i2c-ic";
+ i2c_gr: i2c-global-regs at 0 {
+ compatible = "aspeed,ast2500-i2c-gr", "syscon";
reg = <0x0 0x40>;
- interrupts = <12>;
- interrupt-controller;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x40>;
+
+ i2c_ic: interrupt-controller at 0 {
+ #interrupt-cells = <1>;
+ compatible = "aspeed,ast2500-i2c-ic";
+ reg = <0x0 0x4>;
+ interrupts = <12>;
+ interrupt-controller;
+ };
};
i2c0: i2c-bus at 40 {
@@ -39,11 +122,40 @@ i2c {
#size-cells = <0>;
#interrupt-cells = <1>;
reg = <0x40 0x40>;
- compatible = "aspeed,ast2400-i2c-bus";
+ compatible = "aspeed,ast2500-i2c-bus";
clocks = <&syscon ASPEED_CLK_APB>;
resets = <&syscon ASPEED_RESET_I2C>;
bus-frequency = <100000>;
interrupts = <0>;
interrupt-parent = <&i2c_ic>;
};
+
+ /* buffer mode transfer enabled */
+ i2c1: i2c-bus at 80 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #interrupt-cells = <1>;
+ reg = <0x80 0x40>, <0x210 0x10>;
+ compatible = "aspeed,ast2500-i2c-bus";
+ clocks = <&syscon ASPEED_CLK_APB>;
+ resets = <&syscon ASPEED_RESET_I2C>;
+ bus-frequency = <100000>;
+ interrupts = <1>;
+ interrupt-parent = <&i2c_ic>;
+ };
+
+ /* DMA mode transfer enabled */
+ i2c2: i2c-bus at c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #interrupt-cells = <1>;
+ reg = <0xc0 0x40>;
+ aspeed,dma-buf-size = <4095>;
+ compatible = "aspeed,ast2500-i2c-bus";
+ clocks = <&syscon ASPEED_CLK_APB>;
+ resets = <&syscon ASPEED_RESET_I2C>;
+ bus-frequency = <100000>;
+ interrupts = <2>;
+ interrupt-parent = <&i2c_ic>;
+ };
};
--
2.17.1
More information about the Linux-aspeed
mailing list