[PATCH 6/6] ARM: dts: aspeed: rainier: Add leds that are on optional PCI cable cards

vishwanatha subbanna vishwa at linux.vnet.ibm.com
Wed Feb 10 22:16:57 AEDT 2021



> On 16-Nov-2020, at 11:43 AM, Joel Stanley <joel at jms.id.au> wrote:
> 
> On Fri, 13 Nov 2020 at 05:59, Vishwanatha Subbanna
> <vishwa at linux.vnet.ibm.com> wrote:
>> 
>> These are LEDs on the cable cards that plug into PCIE slots.
>> The LEDs are controlled by PCA9552 I2C expander
>> 
>> Signed-off-by: Vishwanatha Subbanna <vishwa at linux.vnet.ibm.com>
>> ---
>> arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 288 +++++++++++++++++++++++++++
>> 1 file changed, 288 insertions(+)
>> 
>> diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
>> index 67c8c40..7de5f76 100644
>> --- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
>> +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
>> @@ -696,6 +696,70 @@
>>                        gpios = <&pca4 7 GPIO_ACTIVE_LOW>;
>>                };
>>        };
>> +
>> +       leds-optional-cablecard0 {
> 
> Is it necessary to have separate nodes for each of the different GPIO devices?
> 
> Would it make sense to combine them, or is it better to be separate?
> 
> Andrew, Eddie, Brad: please review this one before I merge it.

I answered this in previous patch set.  If I express ‘em all in one node that is “leds {", then if any of the GPIO is not seen because of not having the card, then the current leds-gpio driver knocks off all the ones on which it successfully acquired the GPIOs also, leaving nothing. I did speak to the maintainer and it looked like the behaviour was existing since long time and changing it would break old code.


> 
>> +               compatible = "gpio-leds";
>> +
>> +               cablecard0-cxp-top {
>> +                       retain-state-shutdown;
>> +                       default-state = "keep";
>> +                       gpios = <&pca5 0 GPIO_ACTIVE_LOW>;
>> +               };
>> +
>> +               cablecard0-cxp-bot {
>> +                       retain-state-shutdown;
>> +                       default-state = "keep";
>> +                       gpios = <&pca5 1 GPIO_ACTIVE_LOW>;
>> +               };
>> +       };
>> +
>> +       leds-optional-cablecard3 {
>> +               compatible = "gpio-leds";
>> +
>> +               cablecard3-cxp-top {
>> +                       retain-state-shutdown;
>> +                       default-state = "keep";
>> +                       gpios = <&pca6 0 GPIO_ACTIVE_LOW>;
>> +               };
>> +
>> +               cablecard3-cxp-bot {
>> +                       retain-state-shutdown;
>> +                       default-state = "keep";
>> +                       gpios = <&pca6 1 GPIO_ACTIVE_LOW>;
>> +               };
>> +       };
>> +
>> +       leds-optional-cablecard4 {
>> +               compatible = "gpio-leds";
>> +
>> +               cablecard4-cxp-top {
>> +                       retain-state-shutdown;
>> +                       default-state = "keep";
>> +                       gpios = <&pca7 0 GPIO_ACTIVE_LOW>;
>> +               };
>> +
>> +               cablecard4-cxp-bot {
>> +                       retain-state-shutdown;
>> +                       default-state = "keep";
>> +                       gpios = <&pca7 1 GPIO_ACTIVE_LOW>;
>> +               };
>> +       };
>> +
>> +       leds-optional-cablecard10 {
>> +               compatible = "gpio-leds";
>> +
>> +               cablecard10-cxp-top {
>> +                       retain-state-shutdown;
>> +                       default-state = "keep";
>> +                       gpios = <&pca8 0 GPIO_ACTIVE_LOW>;
>> +               };
>> +
>> +               cablecard10-cxp-bot {
>> +                       retain-state-shutdown;
>> +                       default-state = "keep";
>> +                       gpios = <&pca8 1 GPIO_ACTIVE_LOW>;
>> +               };
>> +       };
>> };
>> 
>> &ehci1 {
>> @@ -1212,6 +1276,180 @@
>>                compatible = "atmel,24c64";
>>                reg = <0x52>;
>>        };
>> +
>> +       pca5: pca9551 at 60 {
>> +               compatible = "nxp,pca9551";
>> +               reg = <0x60>;
>> +               #address-cells = <1>;
>> +               #size-cells = <0>;
>> +
>> +               gpio-controller;
>> +               #gpio-cells = <2>;
>> +
>> +               gpio at 0 {
>> +                       reg = <0>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 1 {
>> +                       reg = <1>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 2 {
>> +                       reg = <2>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 3 {
>> +                       reg = <3>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 4 {
>> +                       reg = <4>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 5 {
>> +                       reg = <5>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 6 {
>> +                       reg = <6>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 7 {
>> +                       reg = <7>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +       };
>> +};
>> +
>> +&i2c5 {
>> +       status = "okay";
>> +
>> +       tmp275 at 48 {
>> +               compatible = "ti,tmp275";
>> +               reg = <0x48>;
>> +       };
>> +
>> +       tmp275 at 49 {
>> +               compatible = "ti,tmp275";
>> +               reg = <0x49>;
>> +       };
>> +
>> +       eeprom at 50 {
>> +               compatible = "atmel,24c64";
>> +               reg = <0x50>;
>> +       };
>> +
>> +       eeprom at 51 {
>> +               compatible = "atmel,24c64";
>> +               reg = <0x51>;
>> +       };
>> +
>> +       pca6: pca9551 at 60 {
>> +               compatible = "nxp,pca9551";
>> +               reg = <0x60>;
>> +               #address-cells = <1>;
>> +               #size-cells = <0>;
>> +
>> +               gpio-controller;
>> +               #gpio-cells = <2>;
>> +
>> +               gpio at 0 {
>> +                       reg = <0>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 1 {
>> +                       reg = <1>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 2 {
>> +                       reg = <2>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 3 {
>> +                       reg = <3>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 4 {
>> +                       reg = <4>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 5 {
>> +                       reg = <5>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 6 {
>> +                       reg = <6>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 7 {
>> +                       reg = <7>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +       };
>> +
>> +       pca7: pca9551 at 61 {
>> +               compatible = "nxp,pca9551";
>> +               reg = <0x61>;
>> +               #address-cells = <1>;
>> +               #size-cells = <0>;
>> +
>> +               gpio-controller;
>> +               #gpio-cells = <2>;
>> +
>> +               gpio at 0 {
>> +                       reg = <0>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 1 {
>> +                       reg = <1>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 2 {
>> +                       reg = <2>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 3 {
>> +                       reg = <3>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 4 {
>> +                       reg = <4>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 5 {
>> +                       reg = <5>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 6 {
>> +                       reg = <6>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 7 {
>> +                       reg = <7>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +       };
>> };
>> 
>> &i2c5 {
>> @@ -2028,6 +2266,56 @@
>>                compatible = "atmel,24c64";
>>                reg = <0x51>;
>>        };
>> +
>> +       pca8: pca9551 at 60 {
>> +               compatible = "nxp,pca9551";
>> +               reg = <0x60>;
>> +               #address-cells = <1>;
>> +               #size-cells = <0>;
>> +
>> +               gpio-controller;
>> +               #gpio-cells = <2>;
>> +
>> +               gpio at 0 {
>> +                       reg = <0>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 1 {
>> +                       reg = <1>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 2 {
>> +                       reg = <2>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 3 {
>> +                       reg = <3>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 4 {
>> +                       reg = <4>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 5 {
>> +                       reg = <5>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 6 {
>> +                       reg = <6>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +
>> +               gpio at 7 {
>> +                       reg = <7>;
>> +                       type = <PCA955X_TYPE_GPIO>;
>> +               };
>> +       };
>> };
>> 
>> &i2c12 {
>> --
>> 1.8.3.1
>> 



More information about the Linux-aspeed mailing list