[PATCH v2 07/15] peci: Add peci-aspeed controller driver
Iwona Winiarska
iwona.winiarska at intel.com
Tue Aug 3 21:31:26 AEST 2021
From: Jae Hyun Yoo <jae.hyun.yoo at linux.intel.com>
ASPEED AST24xx/AST25xx/AST26xx SoCs supports the PECI electrical
interface (a.k.a PECI wire).
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo at linux.intel.com>
Co-developed-by: Iwona Winiarska <iwona.winiarska at intel.com>
Signed-off-by: Iwona Winiarska <iwona.winiarska at intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart at linux.intel.com>
---
MAINTAINERS | 9 +
drivers/peci/Kconfig | 6 +
drivers/peci/Makefile | 3 +
drivers/peci/controller/Kconfig | 16 +
drivers/peci/controller/Makefile | 3 +
drivers/peci/controller/peci-aspeed.c | 445 ++++++++++++++++++++++++++
6 files changed, 482 insertions(+)
create mode 100644 drivers/peci/controller/Kconfig
create mode 100644 drivers/peci/controller/Makefile
create mode 100644 drivers/peci/controller/peci-aspeed.c
diff --git a/MAINTAINERS b/MAINTAINERS
index d411974aaa5e..6e9d53ff68ab 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2866,6 +2866,15 @@ S: Maintained
F: Documentation/hwmon/asc7621.rst
F: drivers/hwmon/asc7621.c
+ASPEED PECI CONTROLLER
+M: Iwona Winiarska <iwona.winiarska at intel.com>
+M: Jae Hyun Yoo <jae.hyun.yoo at linux.intel.com>
+L: linux-aspeed at lists.ozlabs.org (moderated for non-subscribers)
+L: openbmc at lists.ozlabs.org (moderated for non-subscribers)
+S: Supported
+F: Documentation/devicetree/bindings/peci/peci-aspeed.yaml
+F: drivers/peci/controller/peci-aspeed.c
+
ASPEED PINCTRL DRIVERS
M: Andrew Jeffery <andrew at aj.id.au>
L: linux-aspeed at lists.ozlabs.org (moderated for non-subscribers)
diff --git a/drivers/peci/Kconfig b/drivers/peci/Kconfig
index 71a4ad81225a..99279df97a78 100644
--- a/drivers/peci/Kconfig
+++ b/drivers/peci/Kconfig
@@ -13,3 +13,9 @@ menuconfig PECI
This support is also available as a module. If so, the module
will be called peci.
+
+if PECI
+
+source "drivers/peci/controller/Kconfig"
+
+endif # PECI
diff --git a/drivers/peci/Makefile b/drivers/peci/Makefile
index e789a354e842..926d8df15cbd 100644
--- a/drivers/peci/Makefile
+++ b/drivers/peci/Makefile
@@ -3,3 +3,6 @@
# Core functionality
peci-y := core.o
obj-$(CONFIG_PECI) += peci.o
+
+# Hardware specific bus drivers
+obj-y += controller/
diff --git a/drivers/peci/controller/Kconfig b/drivers/peci/controller/Kconfig
new file mode 100644
index 000000000000..6d48df08db1c
--- /dev/null
+++ b/drivers/peci/controller/Kconfig
@@ -0,0 +1,16 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+config PECI_ASPEED
+ tristate "ASPEED PECI support"
+ depends on ARCH_ASPEED || COMPILE_TEST
+ depends on OF
+ depends on HAS_IOMEM
+ help
+ This option enables PECI controller driver for ASPEED AST2400,
+ AST2500 and AST2600 SoCs.
+
+ Say Y here if your system runs on ASPEED SoC and you are using it
+ as BMC for Intel platform.
+
+ This driver can also be built as a module. If so, the module will
+ be called peci-aspeed.
diff --git a/drivers/peci/controller/Makefile b/drivers/peci/controller/Makefile
new file mode 100644
index 000000000000..022c28ef1bf0
--- /dev/null
+++ b/drivers/peci/controller/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+obj-$(CONFIG_PECI_ASPEED) += peci-aspeed.o
diff --git a/drivers/peci/controller/peci-aspeed.c b/drivers/peci/controller/peci-aspeed.c
new file mode 100644
index 000000000000..1d708c983749
--- /dev/null
+++ b/drivers/peci/controller/peci-aspeed.c
@@ -0,0 +1,445 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012-2017 ASPEED Technology Inc.
+// Copyright (c) 2018-2021 Intel Corporation
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/jiffies.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/peci.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+
+#include <asm/unaligned.h>
+
+/* ASPEED PECI Registers */
+/* Control Register */
+#define ASPEED_PECI_CTRL 0x00
+#define ASPEED_PECI_CTRL_SAMPLING_MASK GENMASK(19, 16)
+#define ASPEED_PECI_CTRL_RD_MODE_MASK GENMASK(13, 12)
+#define ASPEED_PECI_CTRL_RD_MODE_DBG BIT(13)
+#define ASPEED_PECI_CTRL_RD_MODE_COUNT BIT(12)
+#define ASPEED_PECI_CTRL_CLK_SOURCE BIT(11)
+#define ASPEED_PECI_CTRL_CLK_DIV_MASK GENMASK(10, 8)
+#define ASPEED_PECI_CTRL_INVERT_OUT BIT(7)
+#define ASPEED_PECI_CTRL_INVERT_IN BIT(6)
+#define ASPEED_PECI_CTRL_BUS_CONTENTION_EN BIT(5)
+#define ASPEED_PECI_CTRL_PECI_EN BIT(4)
+#define ASPEED_PECI_CTRL_PECI_CLK_EN BIT(0)
+
+/* Timing Negotiation Register */
+#define ASPEED_PECI_TIMING_NEGOTIATION 0x04
+#define ASPEED_PECI_T_NEGO_MSG_MASK GENMASK(15, 8)
+#define ASPEED_PECI_T_NEGO_ADDR_MASK GENMASK(7, 0)
+
+/* Command Register */
+#define ASPEED_PECI_CMD 0x08
+#define ASPEED_PECI_CMD_PIN_MONITORING BIT(31)
+#define ASPEED_PECI_CMD_STS_MASK GENMASK(27, 24)
+#define ASPEED_PECI_CMD_STS_ADDR_T_NEGO 0x3
+#define ASPEED_PECI_CMD_IDLE_MASK \
+ (ASPEED_PECI_CMD_STS_MASK | ASPEED_PECI_CMD_PIN_MONITORING)
+#define ASPEED_PECI_CMD_FIRE BIT(0)
+
+/* Read/Write Length Register */
+#define ASPEED_PECI_RW_LENGTH 0x0c
+#define ASPEED_PECI_AW_FCS_EN BIT(31)
+#define ASPEED_PECI_RD_LEN_MASK GENMASK(23, 16)
+#define ASPEED_PECI_WR_LEN_MASK GENMASK(15, 8)
+#define ASPEED_PECI_TARGET_ADDR_MASK GENMASK(7, 0)
+
+/* Expected FCS Data Register */
+#define ASPEED_PECI_EXPECTED_FCS 0x10
+#define ASPEED_PECI_EXPECTED_RD_FCS_MASK GENMASK(23, 16)
+#define ASPEED_PECI_EXPECTED_AW_FCS_AUTO_MASK GENMASK(15, 8)
+#define ASPEED_PECI_EXPECTED_WR_FCS_MASK GENMASK(7, 0)
+
+/* Captured FCS Data Register */
+#define ASPEED_PECI_CAPTURED_FCS 0x14
+#define ASPEED_PECI_CAPTURED_RD_FCS_MASK GENMASK(23, 16)
+#define ASPEED_PECI_CAPTURED_WR_FCS_MASK GENMASK(7, 0)
+
+/* Interrupt Register */
+#define ASPEED_PECI_INT_CTRL 0x18
+#define ASPEED_PECI_TIMING_NEGO_SEL_MASK GENMASK(31, 30)
+#define ASPEED_PECI_1ST_BIT_OF_ADDR_NEGO 0
+#define ASPEED_PECI_2ND_BIT_OF_ADDR_NEGO 1
+#define ASPEED_PECI_MESSAGE_NEGO 2
+#define ASPEED_PECI_INT_MASK GENMASK(4, 0)
+#define ASPEED_PECI_INT_BUS_TIMEOUT BIT(4)
+#define ASPEED_PECI_INT_BUS_CONTENTION BIT(3)
+#define ASPEED_PECI_INT_WR_FCS_BAD BIT(2)
+#define ASPEED_PECI_INT_WR_FCS_ABORT BIT(1)
+#define ASPEED_PECI_INT_CMD_DONE BIT(0)
+
+/* Interrupt Status Register */
+#define ASPEED_PECI_INT_STS 0x1c
+#define ASPEED_PECI_INT_TIMING_RESULT_MASK GENMASK(29, 16)
+ /* bits[4..0]: Same bit fields in the 'Interrupt Register' */
+
+/* Rx/Tx Data Buffer Registers */
+#define ASPEED_PECI_WR_DATA0 0x20
+#define ASPEED_PECI_WR_DATA1 0x24
+#define ASPEED_PECI_WR_DATA2 0x28
+#define ASPEED_PECI_WR_DATA3 0x2c
+#define ASPEED_PECI_RD_DATA0 0x30
+#define ASPEED_PECI_RD_DATA1 0x34
+#define ASPEED_PECI_RD_DATA2 0x38
+#define ASPEED_PECI_RD_DATA3 0x3c
+#define ASPEED_PECI_WR_DATA4 0x40
+#define ASPEED_PECI_WR_DATA5 0x44
+#define ASPEED_PECI_WR_DATA6 0x48
+#define ASPEED_PECI_WR_DATA7 0x4c
+#define ASPEED_PECI_RD_DATA4 0x50
+#define ASPEED_PECI_RD_DATA5 0x54
+#define ASPEED_PECI_RD_DATA6 0x58
+#define ASPEED_PECI_RD_DATA7 0x5c
+#define ASPEED_PECI_DATA_BUF_SIZE_MAX 32
+
+/* Timing Negotiation */
+#define ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT 8
+#define ASPEED_PECI_RD_SAMPLING_POINT_MAX (BIT(4) - 1)
+#define ASPEED_PECI_CLK_DIV_DEFAULT 0
+#define ASPEED_PECI_CLK_DIV_MAX (BIT(3) - 1)
+#define ASPEED_PECI_MSG_TIMING_DEFAULT 1
+#define ASPEED_PECI_MSG_TIMING_MAX (BIT(8) - 1)
+#define ASPEED_PECI_ADDR_TIMING_DEFAULT 1
+#define ASPEED_PECI_ADDR_TIMING_MAX (BIT(8) - 1)
+
+/* Timeout */
+#define ASPEED_PECI_IDLE_CHECK_TIMEOUT_US (50 * USEC_PER_MSEC)
+#define ASPEED_PECI_IDLE_CHECK_INTERVAL_US (10 * USEC_PER_MSEC)
+#define ASPEED_PECI_CMD_TIMEOUT_MS_DEFAULT (1000)
+#define ASPEED_PECI_CMD_TIMEOUT_MS_MAX (1000)
+
+struct aspeed_peci {
+ struct peci_controller *controller;
+ struct device *dev;
+ void __iomem *base;
+ struct clk *clk;
+ struct reset_control *rst;
+ int irq;
+ spinlock_t lock; /* to sync completion status handling */
+ struct completion xfer_complete;
+ u32 status;
+ u32 cmd_timeout_ms;
+ u32 msg_timing;
+ u32 addr_timing;
+ u32 rd_sampling_point;
+ u32 clk_div;
+};
+
+static void aspeed_peci_init_regs(struct aspeed_peci *priv)
+{
+ u32 val;
+
+ val = FIELD_PREP(ASPEED_PECI_CTRL_CLK_DIV_MASK, ASPEED_PECI_CLK_DIV_DEFAULT);
+ val |= ASPEED_PECI_CTRL_PECI_CLK_EN;
+ writel(val, priv->base + ASPEED_PECI_CTRL);
+ /*
+ * Timing negotiation period setting.
+ * The unit of the programmed value is 4 times of PECI clock period.
+ */
+ val = FIELD_PREP(ASPEED_PECI_T_NEGO_MSG_MASK, priv->msg_timing);
+ val |= FIELD_PREP(ASPEED_PECI_T_NEGO_ADDR_MASK, priv->addr_timing);
+ writel(val, priv->base + ASPEED_PECI_TIMING_NEGOTIATION);
+
+ /* Clear interrupts */
+ val = readl(priv->base + ASPEED_PECI_INT_STS) | ASPEED_PECI_INT_MASK;
+ writel(val, priv->base + ASPEED_PECI_INT_STS);
+
+ /* Set timing negotiation mode and enable interrupts */
+ val = FIELD_PREP(ASPEED_PECI_TIMING_NEGO_SEL_MASK, ASPEED_PECI_1ST_BIT_OF_ADDR_NEGO);
+ val |= ASPEED_PECI_INT_MASK;
+ writel(val, priv->base + ASPEED_PECI_INT_CTRL);
+
+ val = FIELD_PREP(ASPEED_PECI_CTRL_SAMPLING_MASK, priv->rd_sampling_point);
+ val |= FIELD_PREP(ASPEED_PECI_CTRL_CLK_DIV_MASK, priv->clk_div);
+ val |= ASPEED_PECI_CTRL_PECI_EN;
+ val |= ASPEED_PECI_CTRL_PECI_CLK_EN;
+ writel(val, priv->base + ASPEED_PECI_CTRL);
+}
+
+static inline int aspeed_peci_check_idle(struct aspeed_peci *priv)
+{
+ u32 cmd_sts = readl(priv->base + ASPEED_PECI_CMD);
+
+ if (FIELD_GET(ASPEED_PECI_CMD_STS_MASK, cmd_sts) == ASPEED_PECI_CMD_STS_ADDR_T_NEGO)
+ aspeed_peci_init_regs(priv);
+
+ return readl_poll_timeout(priv->base + ASPEED_PECI_CMD,
+ cmd_sts,
+ !(cmd_sts & ASPEED_PECI_CMD_IDLE_MASK),
+ ASPEED_PECI_IDLE_CHECK_INTERVAL_US,
+ ASPEED_PECI_IDLE_CHECK_TIMEOUT_US);
+}
+
+static int aspeed_peci_xfer(struct peci_controller *controller,
+ u8 addr, struct peci_request *req)
+{
+ struct aspeed_peci *priv = dev_get_drvdata(controller->dev.parent);
+ unsigned long flags, timeout = msecs_to_jiffies(priv->cmd_timeout_ms);
+ u32 peci_head;
+ int ret;
+
+ if (req->tx.len > ASPEED_PECI_DATA_BUF_SIZE_MAX ||
+ req->rx.len > ASPEED_PECI_DATA_BUF_SIZE_MAX)
+ return -EINVAL;
+
+ /* Check command sts and bus idle state */
+ ret = aspeed_peci_check_idle(priv);
+ if (ret)
+ return ret; /* -ETIMEDOUT */
+
+ spin_lock_irqsave(&priv->lock, flags);
+ reinit_completion(&priv->xfer_complete);
+
+ peci_head = FIELD_PREP(ASPEED_PECI_TARGET_ADDR_MASK, addr) |
+ FIELD_PREP(ASPEED_PECI_WR_LEN_MASK, req->tx.len) |
+ FIELD_PREP(ASPEED_PECI_RD_LEN_MASK, req->rx.len);
+
+ writel(peci_head, priv->base + ASPEED_PECI_RW_LENGTH);
+
+ memcpy_toio(priv->base + ASPEED_PECI_WR_DATA0, req->tx.buf, min_t(u8, req->tx.len, 16));
+ if (req->tx.len > 16)
+ memcpy_toio(priv->base + ASPEED_PECI_WR_DATA4, req->tx.buf + 16,
+ req->tx.len - 16);
+
+ dev_dbg(priv->dev, "HEAD : 0x%08x\n", peci_head);
+ print_hex_dump_bytes("TX : ", DUMP_PREFIX_NONE, req->tx.buf, req->tx.len);
+
+ priv->status = 0;
+ writel(ASPEED_PECI_CMD_FIRE, priv->base + ASPEED_PECI_CMD);
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ ret = wait_for_completion_interruptible_timeout(&priv->xfer_complete, timeout);
+ if (ret < 0)
+ return ret;
+
+ if (ret == 0) {
+ dev_dbg(priv->dev, "Timeout waiting for a response!\n");
+ return -ETIMEDOUT;
+ }
+
+ spin_lock_irqsave(&priv->lock, flags);
+
+ writel(0, priv->base + ASPEED_PECI_CMD);
+
+ if (priv->status != ASPEED_PECI_INT_CMD_DONE) {
+ spin_unlock_irqrestore(&priv->lock, flags);
+ dev_dbg(priv->dev, "No valid response!\n");
+ return -EIO;
+ }
+
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ memcpy_fromio(req->rx.buf, priv->base + ASPEED_PECI_RD_DATA0, min_t(u8, req->rx.len, 16));
+ if (req->rx.len > 16)
+ memcpy_fromio(req->rx.buf + 16, priv->base + ASPEED_PECI_RD_DATA4,
+ req->rx.len - 16);
+
+ print_hex_dump_bytes("RX : ", DUMP_PREFIX_NONE, req->rx.buf, req->rx.len);
+
+ return 0;
+}
+
+static irqreturn_t aspeed_peci_irq_handler(int irq, void *arg)
+{
+ struct aspeed_peci *priv = arg;
+ u32 status;
+
+ spin_lock(&priv->lock);
+ status = readl(priv->base + ASPEED_PECI_INT_STS);
+ writel(status, priv->base + ASPEED_PECI_INT_STS);
+ priv->status |= (status & ASPEED_PECI_INT_MASK);
+
+ /*
+ * In most cases, interrupt bits will be set one by one but also note
+ * that multiple interrupt bits could be set at the same time.
+ */
+ if (status & ASPEED_PECI_INT_BUS_TIMEOUT)
+ dev_dbg_ratelimited(priv->dev, "ASPEED_PECI_INT_BUS_TIMEOUT\n");
+
+ if (status & ASPEED_PECI_INT_BUS_CONTENTION)
+ dev_dbg_ratelimited(priv->dev, "ASPEED_PECI_INT_BUS_CONTENTION\n");
+
+ if (status & ASPEED_PECI_INT_WR_FCS_BAD)
+ dev_dbg_ratelimited(priv->dev, "ASPEED_PECI_INT_WR_FCS_BAD\n");
+
+ if (status & ASPEED_PECI_INT_WR_FCS_ABORT)
+ dev_dbg_ratelimited(priv->dev, "ASPEED_PECI_INT_WR_FCS_ABORT\n");
+
+ /*
+ * All commands should be ended up with a ASPEED_PECI_INT_CMD_DONE bit
+ * set even in an error case.
+ */
+ if (status & ASPEED_PECI_INT_CMD_DONE)
+ complete(&priv->xfer_complete);
+
+ spin_unlock(&priv->lock);
+
+ return IRQ_HANDLED;
+}
+
+static void aspeed_peci_property_sanitize(struct device *dev, const char *propname,
+ u32 min, u32 max, u32 default_val, u32 *propval)
+{
+ u32 val;
+ int ret;
+
+ ret = device_property_read_u32(dev, propname, &val);
+ if (ret) {
+ val = default_val;
+ } else if (val > max || val < min) {
+ dev_warn(dev, "Invalid %s: %u, falling back to: %u\n",
+ propname, val, default_val);
+
+ val = default_val;
+ }
+
+ *propval = val;
+}
+
+static void aspeed_peci_property_setup(struct aspeed_peci *priv)
+{
+ aspeed_peci_property_sanitize(priv->dev, "aspeed,clock-divider",
+ 0, ASPEED_PECI_CLK_DIV_MAX,
+ ASPEED_PECI_CLK_DIV_DEFAULT, &priv->clk_div);
+ aspeed_peci_property_sanitize(priv->dev, "aspeed,msg-timing",
+ 0, ASPEED_PECI_MSG_TIMING_MAX,
+ ASPEED_PECI_MSG_TIMING_DEFAULT, &priv->msg_timing);
+ aspeed_peci_property_sanitize(priv->dev, "aspeed,addr-timing",
+ 0, ASPEED_PECI_ADDR_TIMING_MAX,
+ ASPEED_PECI_ADDR_TIMING_DEFAULT, &priv->addr_timing);
+ aspeed_peci_property_sanitize(priv->dev, "aspeed,rd-sampling-point",
+ 0, ASPEED_PECI_RD_SAMPLING_POINT_MAX,
+ ASPEED_PECI_RD_SAMPLING_POINT_DEFAULT,
+ &priv->rd_sampling_point);
+ aspeed_peci_property_sanitize(priv->dev, "cmd-timeout-ms",
+ 1, ASPEED_PECI_CMD_TIMEOUT_MS_MAX,
+ ASPEED_PECI_CMD_TIMEOUT_MS_DEFAULT, &priv->cmd_timeout_ms);
+}
+
+static struct peci_controller_ops aspeed_ops = {
+ .xfer = aspeed_peci_xfer,
+};
+
+static void aspeed_peci_reset_control_release(void *data)
+{
+ reset_control_assert(data);
+}
+
+int aspeed_peci_reset_control_deassert(struct device *dev, struct reset_control *rst)
+{
+ int ret;
+
+ ret = reset_control_deassert(rst);
+ if (ret)
+ return ret;
+
+ return devm_add_action_or_reset(dev, aspeed_peci_reset_control_release, rst);
+}
+
+static void aspeed_peci_clk_release(void *data)
+{
+ clk_disable_unprepare(data);
+}
+
+static int aspeed_peci_clk_enable(struct device *dev, struct clk *clk)
+{
+ int ret;
+
+ ret = clk_prepare_enable(clk);
+ if (ret)
+ return ret;
+
+ return devm_add_action_or_reset(dev, aspeed_peci_clk_release, clk);
+}
+
+static int aspeed_peci_probe(struct platform_device *pdev)
+{
+ struct peci_controller *controller;
+ struct aspeed_peci *priv;
+ int ret;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->dev = &pdev->dev;
+ dev_set_drvdata(priv->dev, priv);
+
+ priv->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(priv->base))
+ return PTR_ERR(priv->base);
+
+ priv->irq = platform_get_irq(pdev, 0);
+ if (!priv->irq)
+ return priv->irq;
+
+ ret = devm_request_irq(&pdev->dev, priv->irq, aspeed_peci_irq_handler,
+ 0, "peci-aspeed", priv);
+ if (ret)
+ return ret;
+
+ init_completion(&priv->xfer_complete);
+ spin_lock_init(&priv->lock);
+
+ priv->rst = devm_reset_control_get(&pdev->dev, NULL);
+ if (IS_ERR(priv->rst))
+ return dev_err_probe(priv->dev, PTR_ERR(priv->rst),
+ "failed to get reset control\n");
+
+ ret = aspeed_peci_reset_control_deassert(priv->dev, priv->rst);
+ if (ret)
+ return dev_err_probe(priv->dev, ret, "cannot deassert reset control\n");
+
+ priv->clk = devm_clk_get(priv->dev, NULL);
+ if (IS_ERR(priv->clk))
+ return dev_err_probe(priv->dev, PTR_ERR(priv->clk), "failed to get clk\n");
+
+ ret = aspeed_peci_clk_enable(priv->dev, priv->clk);
+ if (ret)
+ return dev_err_probe(priv->dev, ret, "failed to enable clock\n");
+
+ aspeed_peci_property_setup(priv);
+
+ aspeed_peci_init_regs(priv);
+
+ controller = devm_peci_controller_add(priv->dev, &aspeed_ops);
+ if (IS_ERR(controller))
+ return dev_err_probe(priv->dev, PTR_ERR(controller),
+ "failed to add aspeed peci controller\n");
+
+ priv->controller = controller;
+
+ return 0;
+}
+
+static const struct of_device_id aspeed_peci_of_table[] = {
+ { .compatible = "aspeed,ast2400-peci", },
+ { .compatible = "aspeed,ast2500-peci", },
+ { .compatible = "aspeed,ast2600-peci", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, aspeed_peci_of_table);
+
+static struct platform_driver aspeed_peci_driver = {
+ .probe = aspeed_peci_probe,
+ .driver = {
+ .name = "peci-aspeed",
+ .of_match_table = aspeed_peci_of_table,
+ },
+};
+module_platform_driver(aspeed_peci_driver);
+
+MODULE_AUTHOR("Ryan Chen <ryan_chen at aspeedtech.com>");
+MODULE_AUTHOR("Jae Hyun Yoo <jae.hyun.yoo at linux.intel.com>");
+MODULE_DESCRIPTION("ASPEED PECI driver");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(PECI);
--
2.31.1
More information about the Linux-aspeed
mailing list