[PATCH v4 1/4] dt-bindings: i2c: aspeed: add transfer mode support

Jae Hyun Yoo jae.hyun.yoo at linux.intel.com
Fri Apr 9 03:50:41 AEST 2021


Ping.

On 3/10/2021 7:55 AM, Jae Hyun Yoo wrote:
> On 3/9/2021 6:15 PM, Rob Herring wrote:
>> On Tue, Mar 9, 2021 at 10:02 AM Jae Hyun Yoo
>> <jae.hyun.yoo at linux.intel.com> wrote:
>>>
>>> Hi Rob,
>>>
>>> On 3/6/2021 12:30 PM, Rob Herring wrote:
>>>> On Wed, Feb 24, 2021 at 11:17:17AM -0800, Jae Hyun Yoo wrote:
>>>>> Append bindings to support transfer mode.
>>>>>
>>>>> Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo at linux.intel.com>
>>>>> Reviewed-by: Brendan Higgins <brendanhiggins at google.com>
>>>>> ---
>>>>> Changes since v3:
>>>>> - None
>>>>>
>>>>> Changes since v2:
>>>>> - Moved SRAM resources back to default dtsi and added mode selection
>>>>>     property.
>>>>>
>>>>> Changes since v1:
>>>>> - Removed buffer reg settings from default device tree and added 
>>>>> the settings
>>>>>     into here to show the predefined buffer range per each bus.
>>>>>
>>>>>    .../devicetree/bindings/i2c/i2c-aspeed.txt    | 37 
>>>>> +++++++++++++++----
>>>>>    1 file changed, 30 insertions(+), 7 deletions(-)
>>>>>
>>>>> diff --git a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt 
>>>>> b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
>>>>> index b47f6ccb196a..242343177324 100644
>>>>> --- a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
>>>>> +++ b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
>>>>> @@ -17,6 +17,20 @@ Optional Properties:
>>>>>    - bus-frequency    : frequency of the bus clock in Hz defaults 
>>>>> to 100 kHz when not
>>>>>                 specified
>>>>>    - multi-master     : states that there is another master active 
>>>>> on this bus.
>>>>> +- aspeed,i2c-xfer-mode      : should be "byte", "buf" or "dma" to 
>>>>> select transfer
>>>>> +                      mode defaults to "byte" mode when not 
>>>>> specified.
>>>>> +
>>>>> +                      I2C DMA mode on AST2500 has these restrictions:
>>>>> +                        - If one of these controllers is enabled
>>>>> +                            * UHCI host controller
>>>>> +                            * MCTP controller
>>>>> +                          I2C has to use buffer mode or byte mode 
>>>>> instead
>>>>> +                          since these controllers run only in DMA 
>>>>> mode and
>>>>> +                          I2C is sharing the same DMA H/W with them.
>>>>> +                        - If one of these controllers uses DMA 
>>>>> mode, I2C
>>>>> +                          can't use DMA mode
>>>>> +                            * SD/eMMC
>>>>> +                            * Port80 snoop
>>>>
>>>> How does one decide between byte or buf mode?
>>>
>>> If a given system makes just one byte r/w transactions most of the time
>>> then byte mode will be a right setting. Otherwise, buf mode is more
>>> efficient because it doesn't generate a bunch of interrupts on every
>>> byte handling.
>>
>> Then why doesn't the driver do byte transactions when it gets small
>> 1-4? byte transactions and buffer transactions when it gets larger
>> sized transactions.
> 
> Good question and it could be an option of this implementation.
> Actually, each mode needs different register handling so we need to add
> additional conditional branches to make it dynamic mode change depends
> on the data size which can be a downside. Also, checked that small
> amount of data transfer efficiency in 'buf' transfer mode is almost same
> to 'byte' mode so there would be no big benefit from the dynamic mode
> change. Of course, we can remove the 'byte' transfer mode but we should
> also provide flexibility of configuration on what this hardware can
> support, IMO.
> 
> Thanks,
> Jae


More information about the Linux-aspeed mailing list