[PATCH] ARM: dts: aspeed: add ASRock E3C246D4I BMC
Zev Weiss
zev at bewilderbeest.net
Thu Apr 1 15:09:20 AEDT 2021
On Wed, Mar 31, 2021 at 10:51:42PM CDT, Joel Stanley wrote:
>Hi Zev,
>
>On Thu, 1 Apr 2021 at 02:57, Zev Weiss <zev at bewilderbeest.net> wrote:
>>
>> This is a relatively low-cost AST2500-based Xeon E-2100/E-2200 series
>> mini-ITX board that we hope can provide a decent platform for OpenBMC
>> development.
>>
>> This initial device-tree provides the necessary configuration for
>> basic BMC functionality such as host power control, serial console and
>> KVM support, and POST code snooping.
>
>The patch looks good! Some minor things below.
>
>When sending subsequent versions, make sure to add -v N to your git
>format-patch to mark it as the Nth version.
>
>You've also set this to be threaded with a previous version of the
>patch. We normally don't do that, and in this case it's doubly
>confusing as you've split this patch out from the previous series.
>
>I noticed you cc'd soc at kernel.org. We normally only do this when we
>want the soc maintainers to apply a patch directly without going
>through another maintainer. In this case the patch should go through
>the aspeed maintainer's tree (me), so you don't need to cc that
>address.
>
Hmm, that came from using './scripts/get_maintainer.pl --no-rolestats'
with git send-email's --cc-cmd flag; does there happen to be a similarly
easy alternative that wouldn't do the "wrong" thing there?
Ack on the rest, will send v3 soon.
Thanks,
Zev
>> Signed-off-by: Zev Weiss <zev at bewilderbeest.net>
>> Reviewed-by: Joel Stanley <joel at jms.id.au>
>> ---
>
>This spot just here is where you should put the changes between v1 and v2.
>
>> arch/arm/boot/dts/Makefile | 1 +
>> .../boot/dts/aspeed-bmc-asrock-e3c246d4i.dts | 202 ++++++++++++++++++
>> 2 files changed, 203 insertions(+)
>> create mode 100644 arch/arm/boot/dts/aspeed-bmc-asrock-e3c246d4i.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 8e5d4ab4e75e..b12911262ca1 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -1406,6 +1406,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
>> aspeed-bmc-ampere-mtjade.dtb \
>> aspeed-bmc-arm-centriq2400-rep.dtb \
>> aspeed-bmc-arm-stardragon4800-rep2.dtb \
>> + aspeed-bmc-asrock-e3c246d4i.dts \
>
>This should be the output name (.dtb).
>
>> aspeed-bmc-bytedance-g220a.dtb \
>> aspeed-bmc-facebook-cmm.dtb \
>> aspeed-bmc-facebook-galaxy100.dtb \
>> diff --git a/arch/arm/boot/dts/aspeed-bmc-asrock-e3c246d4i.dts b/arch/arm/boot/dts/aspeed-bmc-asrock-e3c246d4i.dts
>> new file mode 100644
>> index 000000000000..dcab6e78dfa4
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/aspeed-bmc-asrock-e3c246d4i.dts
>
>The device tree itself looks good!
>
>If you fix up the things I mentioned and send a v3 I will apply it.
>
>Cheers,
>
>Joel
>
>> @@ -0,0 +1,202 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/dts-v1/;
>> +
>> +#include "aspeed-g5.dtsi"
>> +#include <dt-bindings/gpio/aspeed-gpio.h>
>> +#include <dt-bindings/i2c/i2c.h>
>> +
>> +/{
>> + model = "ASRock E3C246D4I BMC";
>> + compatible = "asrock,e3c246d4i-bmc", "aspeed,ast2500";
>> +
>> + aliases {
>> + serial4 = &uart5;
>> + };
>> +
>> + chosen {
>> + stdout-path = &uart5;
>> + bootargs = "console=tty0 console=ttyS4,115200 earlyprintk";
>> + };
>> +
>> + memory at 80000000 {
>> + reg = <0x80000000 0x20000000>;
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> +
>> + heartbeat {
>> + /* BMC_HB_LED_N */
>> + gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>;
>> + linux,default-trigger = "timer";
>> + };
>> +
>> + system-fault {
>> + /* SYSTEM_FAULT_LED_N */
>> + gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
>> + panic-indicator;
>> + };
>> + };
>> +
>> + gpio-keys {
>> + compatible = "gpio-keys";
>> +
>> + uid-button {
>> + label = "uid-button";
>> + gpios = <&gpio ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
>> + linux,code = <ASPEED_GPIO(F, 1)>;
>> + };
>> + };
>> +
>> + iio-hwmon {
>> + compatible = "iio-hwmon";
>> + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
>> + <&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>,
>> + <&adc 10>, <&adc 11>, <&adc 12>;
>> + };
>> +};
>> +
>> +&fmc {
>> + status = "okay";
>> + flash at 0 {
>> + status = "okay";
>> + m25p,fast-read;
>> + label = "bmc";
>> + spi-max-frequency = <100000000>; /* 100 MHz */
>> +#include "openbmc-flash-layout.dtsi"
>> + };
>> +};
>> +
>> +&uart5 {
>> + status = "okay";
>> +};
>> +
>> +&vuart {
>> + status = "okay";
>> + aspeed,sirq-active-high;
>> +};
>> +
>> +&mac0 {
>> + status = "okay";
>> +
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
>> +};
>> +
>> +&i2c1 {
>> + status = "okay";
>> +
>> + /* thermal sensor, one diode run to a disconnected header */
>> + w83773g at 4c {
>> + compatible = "nuvoton,w83773g";
>> + reg = <0x4c>;
>> + };
>> +};
>> +
>> +&i2c3 {
>> + status = "okay";
>> +
>> + /* FRU EEPROM */
>> + eeprom at 57 {
>> + compatible = "st,24c128", "atmel,24c128";
>> + reg = <0x57>;
>> + pagesize = <16>;
>> + };
>> +};
>> +
>> +&video {
>> + status = "okay";
>> +};
>> +
>> +&vhub {
>> + status = "okay";
>> +};
>> +
>> +&lpc_ctrl {
>> + status = "okay";
>> +};
>> +
>> +&lpc_snoop {
>> + status = "okay";
>> + snoop-ports = <0x80>;
>> +};
>> +
>> +&gpio {
>> + status = "okay";
>> + gpio-line-names =
>> + /* A */ "BMC_MAC1_INTB", "BMC_MAC2_INTB", "NMI_BTN_N", "BMC_NMI",
>> + "", "", "", "",
>> + /* B */ "", "", "", "", "", "IRQ_BMC_PCH_SMI_LPC_N", "", "",
>> + /* C */ "", "", "", "", "", "", "", "",
>> + /* D */ "BMC_PSIN", "BMC_PSOUT", "BMC_RESETCON", "RESETCON",
>> + "", "", "", "",
>> + /* E */ "", "", "", "", "", "", "", "",
>> + /* F */ "LOCATORLED_STATUS_N", "LOCATORBTN", "", "",
>> + "", "", "BMC_PCH_SCI_LPC", "BMC_NCSI_MUX_CTL",
>> + /* G */ "HWM_BAT_EN", "CHASSIS_ID0", "CHASSIS_ID1", "CHASSIS_ID2",
>> + "BMC_ALERT1_N_R", "BMC_ALERT2_N_R", "BMC_ALERT3_N", "SML0ALERT",
>> + /* H */ "FM_ME_RCVR_N", "O_PWROK", "SKL_CNL_R", "D4_DIMM_EVENT_3V_N",
>> + "MFG_MODE_N", "BMC_RTCRST", "BMC_HB_LED_N", "BMC_CASEOPEN",
>> + /* I */ "", "", "", "", "", "", "", "",
>> + /* J */ "BMC_READY", "BMC_PCH_BIOS_CS_N", "BMC_SMI", "",
>> + "", "", "", "",
>> + /* K */ "", "", "", "", "", "", "", "",
>> + /* L */ "BMC_CTS1", "BMC_DCD1", "BMC_DSR1", "BMC_RI1",
>> + "BMC_DTR1", "BMC_RTS1", "BMC_TXD1", "BMC_RXD1",
>> + /* M */ "BMC_LAN0_DIS_N", "BMC_LAN1_DIS_N", "", "",
>> + "", "", "", "",
>> + /* N */ "", "", "", "", "", "", "", "",
>> + /* O */ "", "", "", "", "", "", "", "",
>> + /* P */ "", "", "", "", "", "", "", "",
>> + /* Q */ "", "", "", "",
>> + "BMC_SBM_PRESENT_1_N", "BMC_SBM_PRESENT_2_N",
>> + "BMC_SBM_PRESENT_3_N", "BMC_PCIE_WAKE_N",
>> + /* R */ "", "", "", "", "", "", "", "",
>> + /* S */ "PCHHOT_BMC_N", "", "RSMRST",
>> + "", "", "", "", "",
>> + /* T */ "", "", "", "", "", "", "", "",
>> + /* U */ "", "", "", "", "", "", "", "",
>> + /* V */ "", "", "", "", "", "", "", "",
>> + /* W */ "PS_PWROK", /* dummy always-high signal */
>> + "", "", "", "", "", "", "",
>> + /* X */ "", "", "", "", "", "", "", "",
>> + /* Y */ "SLP_S3", "SLP_S5", "", "", "", "", "", "",
>> + /* Z */ "CPU_CATERR_BMC_PCH_N", "", "SYSTEM_FAULT_LED_N", "BMC_THROTTLE_N",
>> + "", "", "", "",
>> + /* AA */ "CPU1_THERMTRIP_LATCH_N", "", "CPU1_PROCHOT_N", "",
>> + "", "", "IRQ_SMI_ACTIVE_N", "FM_BIOS_POST_CMPLT_N",
>> + /* AB */ "", "", "ME_OVERRIDE", "BMC_DMI_MODIFY",
>> + "", "", "", "",
>> + /* AC */ "LAD0", "LAD1", "LAD2", "LAD3",
>> + "CK_33M_BMC", "LFRAME", "SERIRQ", "S_PLTRST";
>> +
>> + /* Assert BMC_READY so BIOS doesn't sit around waiting for it */
>> + bmc-ready {
>> + gpio-hog;
>> + gpios = <ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
>> + output-high;
>> + };
>> +};
>> +
>> +&adc {
>> + status = "okay";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_adc0_default
>> + &pinctrl_adc1_default
>> + &pinctrl_adc2_default
>> + &pinctrl_adc3_default
>> + &pinctrl_adc4_default
>> + &pinctrl_adc5_default
>> + &pinctrl_adc6_default
>> + &pinctrl_adc7_default
>> + &pinctrl_adc8_default
>> + &pinctrl_adc9_default
>> + &pinctrl_adc10_default
>> + &pinctrl_adc11_default
>> + &pinctrl_adc12_default>;
>> +};
>> +
>> +&kcs3 {
>> + status = "okay";
>> + aspeed,lpc-io-reg = <0xca2>;
>> +};
>> --
>> 2.31.1
>>
More information about the Linux-aspeed
mailing list