[PATCH 2/2] ARM: dts: aspeed: zaius: Add gpio line names

Andrew Jeffery andrew at aj.id.au
Fri Mar 27 10:20:58 AEDT 2020



On Sat, 7 Mar 2020, at 03:32, Andrew Geissler wrote:
> Name the GPIOs to help userspace work with them. The names describe the
> functionality the lines provide, not the net or ball name. This makes it
> easier to share userspace code across different systems and makes the
> use of the lines more obvious.
> 
> Signed-off-by: Andrew Geissler <geissonator at yahoo.com>

So we're creating a bit of an ad-hoc ABI here between the DT and userspace.

Where are we documenting it?

Generally I think the idea is good though, so:

Acked-by: Andrew Jeffery <andrew at aj.id.au>

> ---
>  arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts | 37 +++++++++++++++++++---
>  1 file changed, 33 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts 
> b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
> index bc60ec291681..4bcc82046362 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
> @@ -478,32 +478,61 @@
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_gpioh_unbiased>;
>  
> +	gpio-line-names =
> +	/*A0-A7*/	"","cfam-reset","","","","","","",
> +	/*B0-B7*/	"","","","","","","","",
> +	/*C0-C7*/	"","","","","","","","",
> +	/*D0-D7*/	"fsi-enable","","","","","led-sys-boot-status","led-attention",
> +				"led-fault",
> +	/*E0-E7*/	"","","","","","","","presence-pcie-e2b",
> +	/*F0-F7*/	"","","","","","","","checkstop",
> +	/*G0-G7*/	"fsi-clock","fsi-data","","","","","","",
> +	/*H0-H7*/	"onewire0","onewire1","onewire2","onewire3","","","","",
> +	/*I0-I7*/	"","","","power-button","","","","",
> +	/*J0-J7*/	"","","","","","","","",
> +	/*K0-K7*/	"","","","","","","","",
> +	/*L0-L7*/	"","","","","","","","",
> +	/*M0-M7*/	"","","","","","","","",
> +	/*N0-N7*/	"","","","","","","","",
> +	/*O0-O7*/	"","","","","iso_u164_en","","fsi-trans","",
> +	/*P0-P7*/	"ncsi_mux_en_n","bmc_i2c2_sw_rst_n","","bmc_i2c5_sw_rst_n","",
> +				"","fsi-mux","",
> +	/*Q0-Q7*/	"","","","","","","","",
> +	/*R0-R7*/	"","","","","","","","",
> +	/*S0-S7*/	"","","","","","","","",
> +	/*T0-T7*/	"","","","","","","","",
> +	/*U0-U7*/	"","","","","","","","",
> +	/*V0-V7*/	"","","","","","","","",
> +	/*W0-W7*/	"","","","","","","","",
> +	/*X0-X7*/	"","","","","","","","",
> +	/*Y0-Y7*/	"","","","","","","","",
> +	/*Z0-Z7*/	"","","","","","","","",
> +	/*AA0-AA7*/	"","","led-hdd-fault","","","","","",
> +	/*AB0-AB7*/	"","","","","","","","",
> +	/*AC0-AC7*/	"","","","","","","","";
> +
>  	line_iso_u146_en {
>  		gpio-hog;
>  		gpios = <ASPEED_GPIO(O, 4) GPIO_ACTIVE_HIGH>;
>  		output-high;
> -		line-name = "iso_u164_en";
>  	};
>  
>  	ncsi_mux_en_n {
>  		gpio-hog;
>  		gpios = <ASPEED_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
>  		output-low;
> -		line-name = "ncsi_mux_en_n";
>  	};
>  
>  	line_bmc_i2c2_sw_rst_n {
>  		gpio-hog;
>  		gpios = <ASPEED_GPIO(P, 1) GPIO_ACTIVE_HIGH>;
>  		output-high;
> -		line-name = "bmc_i2c2_sw_rst_n";
>  	};
>  
>  	line_bmc_i2c5_sw_rst_n {
>  		gpio-hog;
>  		gpios = <ASPEED_GPIO(P, 3) GPIO_ACTIVE_HIGH>;
>  		output-high;
> -		line-name = "bmc_i2c5_sw_rst_n";
>  	};
>  };
>  
> -- 
> 2.21.0 (Apple Git-122)
> 
>


More information about the Linux-aspeed mailing list