[PATCH v5 2/6] mmc: sdhci-of-aspeed: Expose clock phase controls
Andrew Jeffery
andrew at aj.id.au
Tue Dec 8 12:26:11 AEDT 2020
The Aspeed SD/eMMC controllers expose configurable clock phase
correction by inserting delays of up to 15 logic elements in length into
the bus clock path. The hardware supports independent configuration for
both bus directions on a per-slot basis.
The timing delay per element encoded in the driver was experimentally
determined by scope measurements.
The phase controls for both slots are grouped together in a single
register of the global register block of the SD/MMC controller(s), which
drives the use of a locking scheme between the SDHCIs and the global
register set.
Signed-off-by: Andrew Jeffery <andrew at aj.id.au>
---
drivers/mmc/host/sdhci-of-aspeed.c | 216 +++++++++++++++++++++++++++--
1 file changed, 208 insertions(+), 8 deletions(-)
diff --git a/drivers/mmc/host/sdhci-of-aspeed.c b/drivers/mmc/host/sdhci-of-aspeed.c
index 4f008ba3280e..788ec7728227 100644
--- a/drivers/mmc/host/sdhci-of-aspeed.c
+++ b/drivers/mmc/host/sdhci-of-aspeed.c
@@ -6,6 +6,7 @@
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/io.h>
+#include <linux/math64.h>
#include <linux/mmc/host.h>
#include <linux/module.h>
#include <linux/of_address.h>
@@ -16,9 +17,19 @@
#include "sdhci-pltfm.h"
-#define ASPEED_SDC_INFO 0x00
-#define ASPEED_SDC_S1MMC8 BIT(25)
-#define ASPEED_SDC_S0MMC8 BIT(24)
+#define ASPEED_SDC_INFO 0x00
+#define ASPEED_SDC_S1_MMC8 BIT(25)
+#define ASPEED_SDC_S0_MMC8 BIT(24)
+#define ASPEED_SDC_PHASE 0xf4
+#define ASPEED_SDC_S1_PHASE_IN GENMASK(25, 21)
+#define ASPEED_SDC_S0_PHASE_IN GENMASK(20, 16)
+#define ASPEED_SDC_S1_PHASE_OUT GENMASK(15, 11)
+#define ASPEED_SDC_S1_PHASE_IN_EN BIT(10)
+#define ASPEED_SDC_S1_PHASE_OUT_EN GENMASK(9, 8)
+#define ASPEED_SDC_S0_PHASE_OUT GENMASK(7, 3)
+#define ASPEED_SDC_S0_PHASE_IN_EN BIT(2)
+#define ASPEED_SDC_S0_PHASE_OUT_EN GENMASK(1, 0)
+#define ASPEED_SDC_PHASE_MAX 31
struct aspeed_sdc {
struct clk *clk;
@@ -28,9 +39,36 @@ struct aspeed_sdc {
void __iomem *regs;
};
+struct aspeed_sdhci_tap_param {
+ bool valid;
+
+#define ASPEED_SDHCI_TAP_PARAM_INVERT_CLK BIT(4)
+ u8 in;
+ u8 out;
+};
+
+struct aspeed_sdhci_tap_desc {
+ u32 tap_mask;
+ u32 enable_mask;
+ u8 enable_value;
+};
+
+struct aspeed_sdhci_phase_desc {
+ struct aspeed_sdhci_tap_desc in;
+ struct aspeed_sdhci_tap_desc out;
+};
+
+struct aspeed_sdhci_pdata {
+ const struct aspeed_sdhci_phase_desc *phase_desc;
+ size_t nr_phase_descs;
+};
+
struct aspeed_sdhci {
+ const struct aspeed_sdhci_pdata *pdata;
struct aspeed_sdc *parent;
u32 width_mask;
+ mmc_clk_phase_map_t phase_map;
+ const struct aspeed_sdhci_phase_desc *phase_desc;
};
static void aspeed_sdc_configure_8bit_mode(struct aspeed_sdc *sdc,
@@ -50,10 +88,118 @@ static void aspeed_sdc_configure_8bit_mode(struct aspeed_sdc *sdc,
spin_unlock(&sdc->lock);
}
+static u32
+aspeed_sdc_set_phase_tap(const struct aspeed_sdhci_tap_desc *desc,
+ u8 tap, bool enable, u32 reg)
+{
+ reg &= ~(desc->enable_mask | desc->tap_mask);
+ if (enable) {
+ reg |= tap << __ffs(desc->tap_mask);
+ reg |= desc->enable_value << __ffs(desc->enable_mask);
+ }
+
+ return reg;
+}
+
+static void
+aspeed_sdc_set_phase_taps(struct aspeed_sdc *sdc,
+ const struct aspeed_sdhci_phase_desc *desc,
+ const struct aspeed_sdhci_tap_param *taps)
+{
+ u32 reg;
+
+ spin_lock(&sdc->lock);
+ reg = readl(sdc->regs + ASPEED_SDC_PHASE);
+
+ reg = aspeed_sdc_set_phase_tap(&desc->in, taps->in, taps->valid, reg);
+ reg = aspeed_sdc_set_phase_tap(&desc->out, taps->out, taps->valid, reg);
+
+ writel(reg, sdc->regs + ASPEED_SDC_PHASE);
+ spin_unlock(&sdc->lock);
+}
+
+#define PICOSECONDS_PER_SECOND 1000000000000ULL
+#define ASPEED_SDHCI_NR_TAPS 15
+/* Measured value with *handwave* environmentals and static loading */
+#define ASPEED_SDHCI_MAX_TAP_DELAY_PS 1253
+static int aspeed_sdhci_phase_to_tap(struct device *dev, unsigned long rate_hz,
+ int phase_deg)
+{
+ u64 phase_period_ps;
+ u64 prop_delay_ps;
+ u64 clk_period_ps;
+ unsigned int tap;
+ u8 inverted;
+
+ phase_deg %= 360;
+
+ if (phase_deg >= 180) {
+ inverted = ASPEED_SDHCI_TAP_PARAM_INVERT_CLK;
+ phase_deg -= 180;
+ dev_dbg(dev,
+ "Inverting clock to reduce phase correction from %d to %d degrees\n",
+ phase_deg + 180, phase_deg);
+ } else {
+ inverted = 0;
+ }
+
+ prop_delay_ps = ASPEED_SDHCI_MAX_TAP_DELAY_PS / ASPEED_SDHCI_NR_TAPS;
+ clk_period_ps = div_u64(PICOSECONDS_PER_SECOND, (u64)rate_hz);
+ phase_period_ps = div_u64((u64)phase_deg * clk_period_ps, 360ULL);
+
+ tap = div_u64(phase_period_ps, prop_delay_ps);
+ if (tap > ASPEED_SDHCI_NR_TAPS) {
+ dev_warn(dev,
+ "Requested out of range phase tap %d for %d degrees of phase compensation at %luHz, clamping to tap %d\n",
+ tap, phase_deg, rate_hz, ASPEED_SDHCI_NR_TAPS);
+ tap = ASPEED_SDHCI_NR_TAPS;
+ }
+
+ return inverted | tap;
+}
+
+static void
+aspeed_sdhci_phases_to_taps(struct device *dev, unsigned long rate,
+ const struct mmc_clk_phase *phases,
+ struct aspeed_sdhci_tap_param *taps)
+{
+ taps->valid = phases->valid;
+
+ if (!phases->valid)
+ return;
+
+ taps->in = aspeed_sdhci_phase_to_tap(dev, rate, phases->in_deg);
+ taps->out = aspeed_sdhci_phase_to_tap(dev, rate, phases->out_deg);
+}
+
+static void
+aspeed_sdhci_configure_phase(struct sdhci_host *host, unsigned long rate)
+{
+ struct aspeed_sdhci_tap_param _taps = {0}, *taps = &_taps;
+ struct mmc_clk_phase *params;
+ struct aspeed_sdhci *sdhci;
+ struct device *dev;
+
+ dev = host->mmc->parent;
+ sdhci = sdhci_pltfm_priv(sdhci_priv(host));
+
+ if (!sdhci->phase_desc)
+ return;
+
+ params = &sdhci->phase_map[host->timing];
+ aspeed_sdhci_phases_to_taps(dev, rate, params, taps);
+ aspeed_sdc_set_phase_taps(sdhci->parent, sdhci->phase_desc, taps);
+ dev_dbg(dev,
+ "Using taps [%d, %d] for [%d, %d] degrees of phase correction at %luHz (%d)\n",
+ taps->in & ASPEED_SDHCI_NR_TAPS,
+ taps->out & ASPEED_SDHCI_NR_TAPS,
+ params->in_deg, params->out_deg, rate, host->timing);
+}
+
static void aspeed_sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
{
struct sdhci_pltfm_host *pltfm_host;
- unsigned long parent;
+ unsigned long parent, bus;
int div;
u16 clk;
@@ -69,13 +215,17 @@ static void aspeed_sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
clock = host->max_clk;
for (div = 2; div < 256; div *= 2) {
- if ((parent / div) <= clock)
+ bus = parent / div;
+ if (bus <= clock)
break;
}
+
div >>= 1;
clk = div << SDHCI_DIVIDER_SHIFT;
+ aspeed_sdhci_configure_phase(host, bus);
+
sdhci_enable_clk(host, clk);
}
@@ -157,6 +307,7 @@ static inline int aspeed_sdhci_calculate_slot(struct aspeed_sdhci *dev,
static int aspeed_sdhci_probe(struct platform_device *pdev)
{
+ const struct aspeed_sdhci_pdata *aspeed_pdata;
struct sdhci_pltfm_host *pltfm_host;
struct aspeed_sdhci *dev;
struct sdhci_host *host;
@@ -164,12 +315,15 @@ static int aspeed_sdhci_probe(struct platform_device *pdev)
int slot;
int ret;
+ aspeed_pdata = of_device_get_match_data(&pdev->dev);
+
host = sdhci_pltfm_init(pdev, &aspeed_sdhci_pdata, sizeof(*dev));
if (IS_ERR(host))
return PTR_ERR(host);
pltfm_host = sdhci_priv(host);
dev = sdhci_pltfm_priv(pltfm_host);
+ dev->pdata = aspeed_pdata;
dev->parent = dev_get_drvdata(pdev->dev.parent);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -180,8 +334,17 @@ static int aspeed_sdhci_probe(struct platform_device *pdev)
else if (slot >= 2)
return -EINVAL;
- dev_info(&pdev->dev, "Configuring for slot %d\n", slot);
- dev->width_mask = !slot ? ASPEED_SDC_S0MMC8 : ASPEED_SDC_S1MMC8;
+ if (dev->pdata && slot < dev->pdata->nr_phase_descs) {
+ dev->phase_desc = &dev->pdata->phase_desc[slot];
+ } else {
+ dev_info(&pdev->dev,
+ "Phase control not supported for slot %d\n", slot);
+ dev->phase_desc = NULL;
+ }
+
+ dev->width_mask = !slot ? ASPEED_SDC_S0_MMC8 : ASPEED_SDC_S1_MMC8;
+
+ dev_info(&pdev->dev, "Configured for slot %d\n", slot);
sdhci_get_of_property(pdev);
@@ -199,6 +362,9 @@ static int aspeed_sdhci_probe(struct platform_device *pdev)
if (ret)
goto err_sdhci_add;
+ if (dev->phase_desc)
+ mmc_of_parse_clk_phase(host->mmc, dev->phase_map);
+
ret = sdhci_add_host(host);
if (ret)
goto err_sdhci_add;
@@ -230,10 +396,44 @@ static int aspeed_sdhci_remove(struct platform_device *pdev)
return 0;
}
+static const struct aspeed_sdhci_phase_desc ast2600_sdhci_phase[] = {
+ /* SDHCI/Slot 0 */
+ [0] = {
+ .in = {
+ .tap_mask = ASPEED_SDC_S0_PHASE_IN,
+ .enable_mask = ASPEED_SDC_S0_PHASE_IN_EN,
+ .enable_value = 1,
+ },
+ .out = {
+ .tap_mask = ASPEED_SDC_S0_PHASE_OUT,
+ .enable_mask = ASPEED_SDC_S0_PHASE_OUT_EN,
+ .enable_value = 3,
+ },
+ },
+ /* SDHCI/Slot 1 */
+ [1] = {
+ .in = {
+ .tap_mask = ASPEED_SDC_S1_PHASE_IN,
+ .enable_mask = ASPEED_SDC_S1_PHASE_IN_EN,
+ .enable_value = 1,
+ },
+ .out = {
+ .tap_mask = ASPEED_SDC_S1_PHASE_OUT,
+ .enable_mask = ASPEED_SDC_S1_PHASE_OUT_EN,
+ .enable_value = 3,
+ },
+ },
+};
+
+static const struct aspeed_sdhci_pdata ast2600_sdhci_pdata = {
+ .phase_desc = ast2600_sdhci_phase,
+ .nr_phase_descs = ARRAY_SIZE(ast2600_sdhci_phase),
+};
+
static const struct of_device_id aspeed_sdhci_of_match[] = {
{ .compatible = "aspeed,ast2400-sdhci", },
{ .compatible = "aspeed,ast2500-sdhci", },
- { .compatible = "aspeed,ast2600-sdhci", },
+ { .compatible = "aspeed,ast2600-sdhci", .data = &ast2600_sdhci_pdata, },
{ }
};
--
2.27.0
More information about the Linux-aspeed
mailing list