[PATCH v2 3/4] gpio: Add in ast2600 details to Aspeed driver

Rashmica Gupta rashmica.g at gmail.com
Thu Sep 5 11:17:32 AEST 2019


The ast2600 is a new generation of SoC from ASPEED. Similarly to the
ast2400 and ast2500, it has a GPIO controller for it's 3.6V GPIO pins.
Additionally, it has a GPIO controller for 36 1.8V GPIO pins. These
voltages are fixed and cannot be configured via pinconf, so we need two
separate drivers for them.

Signed-off-by: Rashmica Gupta <rashmica.g at gmail.com>
---
 drivers/gpio/gpio-aspeed.c | 30 ++++++++++++++++++++++++++++--
 1 file changed, 28 insertions(+), 2 deletions(-)

diff --git a/drivers/gpio/gpio-aspeed.c b/drivers/gpio/gpio-aspeed.c
index 16c6eaf70857..4723b8780a8c 100644
--- a/drivers/gpio/gpio-aspeed.c
+++ b/drivers/gpio/gpio-aspeed.c
@@ -662,12 +662,14 @@ static void aspeed_gpio_irq_handler(struct irq_desc *desc)
 	struct gpio_chip *gc = irq_desc_get_handler_data(desc);
 	struct irq_chip *ic = irq_desc_get_chip(desc);
 	struct aspeed_gpio *data = gpiochip_get_data(gc);
-	unsigned int i, p, girq;
+	unsigned int i, p, girq, banks;
 	unsigned long reg;
+	struct aspeed_gpio *gpio = gpiochip_get_data(gc);
 
 	chained_irq_enter(ic, desc);
 
-	for (i = 0; i < ARRAY_SIZE(aspeed_gpio_banks); i++) {
+	banks = DIV_ROUND_UP(gpio->config->nr_gpios, 32);
+	for (i = 0; i < banks; i++) {
 		const struct aspeed_gpio_bank *bank = &aspeed_gpio_banks[i];
 
 		reg = ioread32(bank_reg(data, bank, reg_irq_status));
@@ -1108,9 +1110,33 @@ static const struct aspeed_gpio_config ast2500_config =
 	/* 232 for simplicity, actual number is 228 (4-GPIO hole in GPIOAB) */
 	{ .nr_gpios = 232, .props = ast2500_bank_props, };
 
+static const struct aspeed_bank_props ast2600_bank_props[] = {
+	/*     input	  output   */
+	{5, 0xffffffff,  0x0000ffff}, /* U/V/W/X */
+	{6, 0xffff0000,  0x0fff0000}, /* Y/Z */
+	{ },
+};
+
+static const struct aspeed_gpio_config ast2600_config =
+	/* 208 3.6V GPIOs */
+	{ .nr_gpios = 208, .props = ast2600_bank_props, };
+
+static const struct aspeed_bank_props ast2600_1_8v_bank_props[] = {
+	/*     input	  output   */
+	{1, 0x0000000f,  0x0000000f}, /* E */
+	{ },
+};
+
+static const struct aspeed_gpio_config ast2600_1_8v_config =
+	/* 36 1.8V GPIOs */
+	{ .nr_gpios = 36, .props = ast2600_1_8v_bank_props, };
+
 static const struct of_device_id aspeed_gpio_of_table[] = {
 	{ .compatible = "aspeed,ast2400-gpio", .data = &ast2400_config, },
 	{ .compatible = "aspeed,ast2500-gpio", .data = &ast2500_config, },
+	{ .compatible = "aspeed,ast2600-gpio", .data = &ast2600_config, },
+	{ .compatible = "aspeed,ast2600-1-8v-gpio",
+	  .data = &ast2600_1_8v_config, },
 	{}
 };
 MODULE_DEVICE_TABLE(of, aspeed_gpio_of_table);
-- 
2.20.1



More information about the Linux-aspeed mailing list