[PATCH v2] ftgmac100: Disable HW checksum generation on AST2500
Vijay Khemka
vijaykhemka at fb.com
Sat Oct 19 09:50:32 AEDT 2019
On 10/17/19, 5:33 PM, "Benjamin Herrenschmidt" <benh at kernel.crashing.org> wrote:
On Fri, 2019-10-18 at 00:06 +0000, Vijay Khemka wrote:
>
> > This is not a matter of unsupported csum, it is broken hw csum.
> > That's why we disable hw checksum. My guess is once we disable
> > Hw checksum, it will use sw checksum. So I am just disabling hw
> > Checksum.
>
> I don't understand what you are saying. You reported a problem with
> IPV6 checksums generation. The HW doesn't support it. What's "not a
> matter of unsupported csum" ?
>
> Your patch uses a *deprecated* bit to tell the network stack to only do
> HW checksum generation on IPV4.
>
> This bit is deprecated for a reason, again, see skbuff.h. The right
> approach, *which the driver already does*, is to tell the stack that we
> support HW checksuming using NETIF_F_HW_CSUM, and then, in the transmit
> handler, to call skb_checksum_help() to have the SW calculate the
> checksum if it's not a supported type.
>
> My understanding was when we enable NETIF_F_HW_CSUM means network
> stack enables HW checksum and doesn't calculate SW checksum. But as per
> this supported types HW checksum are used only for IPV4 and not for IPV6 even
> though driver enabled NETIF_F_HW_CSUM. For IPV6 it is always a SW generated
> checksum, please correct me here.
Have you actually read the comments in skbuff.h that I pointed you to ?
And the rest of my email for that matter ?
Yes, I went through comments in skbuff.h and your comments as well. I knew about
this deprecated bit that's why I have disabled NETIF_F_HW_CSUM completely in my
V1 patch. Then Florian gave a comment and asked me to disable only IPV6 not IPV4
as it is working for IPV4 and issue with only IPV6. That's why I sent patch V2
accommodating his feedback.
I don't have much understanding of IP Stack but I went through code details and
you are right and found that it should fallback to SW calculation for IPV6 but it doesn't
happen because ftgmac100_hard_start_xmit checks for CHECKSUM_PARTIAL before
setting HW checksum and calling ftgmac100_prep_tx_csum function. And in my
understanding, this value is set CHECKSUM_PARTIAL in IP stack. I looked up IP stack for
IPV6, file net/ipv6/ip6_output.c, function __ip6_append_data: here it sets
CHECKSUM_PARTIAL only for UDP packets not for TCP packets. Please look at line
number 1880. This could be an issue we are seeing here as why
ftgmac100_prep_tx_csum is not getting triggered for IPV6 with TCP. Please correct
me if my understanding is wrong.
> This is exactly what ftgmac100_prep_tx_csum() does. It only enables HW
> checksum generation on supported types and uses skb_checksum_help()
> otherwise, supported types being protocol ETH_P_IP and IP protocol
> being raw IP, TCP and UDP.
>
>
> So this *should* have fallen back to SW for IPV6. So either something
> in my code there is making an incorrect assumption, or something is
> broken in skb_checksum_help() for IPV6 (which I somewhat doubt) or
> something else I can't think of, but setting a *deprecated* flag is
> definitely not the right answer, neither is completely disabling HW
> checksumming.
>
> So can you investigate what's going on a bit more closely please ? I
> can try myself, though I have very little experience with IPV6 and
> probably won't have time before next week.
>
> Cheers,
> Ben.
>
> > The driver should have handled unsupported csum via SW fallback
> > already in ftgmac100_prep_tx_csum()
> >
> > Can you check why this didn't work for you ?
> >
> > Cheers,
> > Ben.
> >
> > > Signed-off-by: Vijay Khemka <vijaykhemka at fb.com>
> > > ---
> > > Changes since v1:
> > > Enabled IPV4 hw checksum generation as it works for IPV4.
> > >
> > > drivers/net/ethernet/faraday/ftgmac100.c | 13 ++++++++++++-
> > > 1 file changed, 12 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/drivers/net/ethernet/faraday/ftgmac100.c
> > > b/drivers/net/ethernet/faraday/ftgmac100.c
> > > index 030fed65393e..0255a28d2958 100644
> > > --- a/drivers/net/ethernet/faraday/ftgmac100.c
> > > +++ b/drivers/net/ethernet/faraday/ftgmac100.c
> > > @@ -1842,8 +1842,19 @@ static int ftgmac100_probe(struct
> > > platform_device *pdev)
> > > /* AST2400 doesn't have working HW checksum generation */
> > > if (np && (of_device_is_compatible(np, "aspeed,ast2400-mac")))
> > > netdev->hw_features &= ~NETIF_F_HW_CSUM;
> > > +
> > > + /* AST2500 doesn't have working HW checksum generation for IPV6
> > > + * but it works for IPV4, so disabling hw checksum and enabling
> > > + * it for only IPV4.
> > > + */
> > > + if (np && (of_device_is_compatible(np, "aspeed,ast2500-mac")))
> > > {
> > > + netdev->hw_features &= ~NETIF_F_HW_CSUM;
> > > + netdev->hw_features |= NETIF_F_IP_CSUM;
> > > + }
> > > +
> > > if (np && of_get_property(np, "no-hw-checksum", NULL))
> > > - netdev->hw_features &= ~(NETIF_F_HW_CSUM |
> > > NETIF_F_RXCSUM);
> > > + netdev->hw_features &= ~(NETIF_F_HW_CSUM |
> > > NETIF_F_RXCSUM
> > > + | NETIF_F_IP_CSUM);
> > > netdev->features |= netdev->hw_features;
> > >
> > > /* register network device */
> >
> >
> >
>
>
>
More information about the Linux-aspeed
mailing list