[PATCH dev-5.1] ARM: dts: aspeed: swift: Add pca9539 devices

[Brandon Wyman]

On Mon, May 20, 2019 at 3:17 PM Adriana Kobylak <anoo at linux.ibm.com> wrote:
>
> From: Adriana Kobylak <anoo at us.ibm.com>
>
> Add the pca9539 devices to the Swift device tree.
>
> Signed-off-by: Adriana Kobylak <anoo at us.ibm.com>
> ---
>  arch/arm/boot/dts/aspeed-bmc-opp-swift.dts | 146 +++++++++++++++++++++++++++++
>  1 file changed, 146 insertions(+)
>
> diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts b/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
> index 9610637..270c923 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
> @@ -732,6 +732,79 @@
>                 compatible = "infineon,ir35221";
>                 reg = <0x72>;
>         };
> +
> +       pca2: pca9539 at 74 {
> +               compatible = "nxp,pca9539";
> +               reg = <0x74>;

This looks like the right bus, address, and chip/compatible type, but
what follows after I am not 100% certain on. I do not know the
specifics of how to indicate these are input GPIO pins.

> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +               gpio-controller;
> +               #gpio-cells = <2>;
> +
> +               gpio at 0 {
> +                       reg = <0>;
> +               };
> +
> +               gpio at 1 {
> +                       reg = <1>;
> +               };
> +
> +               gpio at 2 {
> +                       reg = <2>;
> +               };
> +
> +               gpio at 3 {
> +                       reg = <3>;
> +               };
> +
> +               gpio at 4 {
> +                       reg = <4>;
> +               };
> +
> +               gpio at 5 {
> +                       reg = <5>;
> +               };
> +
> +               gpio at 6 {
> +                       reg = <6>;
> +               };
> +
> +               gpio at 7 {
> +                       reg = <7>;
> +               };
> +
> +               gpio at 8 {
> +                       reg = <8>;
> +               };
> +
> +               gpio at 9 {
> +                       reg = <9>;
> +               };
> +
> +               gpio at 10 {
> +                       reg = <10>;
> +               };
> +
> +               gpio at 11 {
> +                       reg = <11>;
> +               };
> +
> +               gpio at 12 {
> +                       reg = <12>;
> +               };
> +
> +               gpio at 13 {
> +                       reg = <13>;
> +               };
> +
> +               gpio at 14 {
> +                       reg = <14>;
> +               };
> +
> +               gpio at 15 {
> +                       reg = <15>;
> +               };
> +       };
>  };
>
>  &i2c10 {
> @@ -756,6 +829,79 @@
>                 compatible = "infineon,ir35221";
>                 reg = <0x72>;
>         };
> +
> +       pca3: pca9539 at 74 {
> +               compatible = "nxp,pca9539";
> +               reg = <0x74>;

This looks like the correct bus, address, and type as well, but again,
not sure on how to make sure they are GPIO input pins.

> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +               gpio-controller;
> +               #gpio-cells = <2>;
> +
> +               gpio at 0 {
> +                       reg = <0>;
> +               };
> +
> +               gpio at 1 {
> +                       reg = <1>;
> +               };
> +
> +               gpio at 2 {
> +                       reg = <2>;
> +               };
> +
> +               gpio at 3 {
> +                       reg = <3>;
> +               };
> +
> +               gpio at 4 {
> +                       reg = <4>;
> +               };
> +
> +               gpio at 5 {
> +                       reg = <5>;
> +               };
> +
> +               gpio at 6 {
> +                       reg = <6>;
> +               };
> +
> +               gpio at 7 {
> +                       reg = <7>;
> +               };
> +
> +               gpio at 8 {
> +                       reg = <8>;
> +               };
> +
> +               gpio at 9 {
> +                       reg = <9>;
> +               };
> +
> +               gpio at 10 {
> +                       reg = <10>;
> +               };
> +
> +               gpio at 11 {
> +                       reg = <11>;
> +               };
> +
> +               gpio at 12 {
> +                       reg = <12>;
> +               };
> +
> +               gpio at 13 {
> +                       reg = <13>;
> +               };
> +
> +               gpio at 14 {
> +                       reg = <14>;
> +               };
> +
> +               gpio at 15 {
> +                       reg = <15>;
> +               };
> +       };
>  };
>
>  &i2c11 {
> --
> 1.8.3.1
>