[PATCH v5] ARM: dts: aspeed: Adding Lenovo Hr630 BMC
Andrew Peng
pengms1 at lenovo.com
Thu Apr 25 16:48:43 AEST 2019
Initial introduction of Lenovo Hr630 family equipped with
Aspeed 2500 BMC SoC. Hr630 is a x86 server development kit
with a ASPEED ast2500 BMC manufactured by Lenovo.
Specifically, This adds the Hr630 platform device tree file
used by the Hr630 BMC machines.
This also adds an entry of Hr630 device tree file in Makefile
Signed-off-by: Andrew Peng <pengms1 at lenovo.com>
Signed-off-by: Yonghui Liu <liuyh21 at lenovo.com>
Signed-off-by: Lisa Liu <liuyj19 at lenovo.com>
---
Changes in v5:
- revise pca9545 and pca9546 switch aliases name.
Changes in v4:
- add pca9546 switch aliases name.
Changes in v3:
- revise i2c switch aliases name.
Changes in v2:
- add i2c switch aliases name.
- remove the unused eeprom device from DT file.
- remove "Licensed under..." sentence.
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts | 890 ++++++++++++++++++++++++++
2 files changed, 892 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f4f5aea..375e53b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1261,4 +1261,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-opp-witherspoon.dtb \
aspeed-bmc-opp-zaius.dtb \
aspeed-bmc-portwell-neptune.dtb \
- aspeed-bmc-quanta-q71l.dtb
+ aspeed-bmc-quanta-q71l.dtb \
+ aspeed-bmc-lenovo-hr630.dtb
diff --git a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
new file mode 100644
index 0000000..4f18f4d
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
@@ -0,0 +1,890 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Device Tree file for Lenovo Hr630 platform
+ *
+ * Copyright (C) 2019-present Lenovo
+ */
+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+ model = "HR630 BMC";
+ compatible = "lenovo,hr630-bmc", "aspeed,ast2500";
+
+ aliases {
+ i2c14 = &i2c_rbp;
+ i2c15 = &i2c_fbp1;
+ i2c16 = &i2c_fbp2;
+ i2c17 = &i2c_fbp3;
+ i2c18 = &i2c_riser2;
+ i2c19 = &i2c_pcie4;
+ i2c20 = &i2c_riser1;
+ i2c21 = &i2c_ocp;
+ };
+
+ chosen {
+ stdout-path = &uart5;
+ bootargs = "console=tty0 console=ttyS4,115200 earlyprintk";
+ };
+
+ memory at 80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ flash_memory: region at 98000000 {
+ no-map;
+ reg = <0x98000000 0x00100000>; /* 1M */
+ };
+
+ gfx_memory: framebuffer {
+ size = <0x01000000>;
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ heartbeat {
+ gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_LOW>;
+ };
+
+ fault {
+ gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+ <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+ <&adc 8>, <&adc 9>, <&adc 10>,
+ <&adc 12>, <&adc 13>, <&adc 14>;
+ };
+
+};
+
+&fmc {
+ status = "okay";
+ flash at 0 {
+ status = "okay";
+ m25p,fast-read;
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout.dtsi"
+ };
+};
+
+&lpc_ctrl {
+ status = "okay";
+ memory-region = <&flash_memory>;
+ flash = <&spi1>;
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&vuart {
+ status = "okay";
+};
+
+&ibt {
+ status = "okay";
+};
+
+&mac0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii1_default>;
+ use-ncsi;
+};
+
+&mac1 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&adc {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ /* temp1 inlet */
+ tmp75 at 4e {
+ compatible = "national,lm75";
+ reg = <0x4e>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ /* temp2 outlet */
+ tmp75 at 4d {
+ compatible = "national,lm75";
+ reg = <0x4d>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&i2c6 {
+ status = "okay";
+ /* Slot 0,
+ * Slot 1,
+ * Slot 2,
+ * Slot 3
+ */
+
+ i2c-switch at 70 {
+ compatible = "nxp,pca9545";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect; /* may use mux at 70 next. */
+
+ i2c_rbp: i2c at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c_fbp1: i2c at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c_fbp2: i2c at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c_fbp3: i2c at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c7 {
+ status = "okay";
+
+ /* Slot 0,
+ * Slot 1,
+ * Slot 2,
+ * Slot 3
+ */
+ i2c-switch at 76 {
+ compatible = "nxp,pca9546";
+ reg = <0x76>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-mux-idle-disconnect; /* may use mux at 76 next. */
+
+ i2c_riser2: i2c at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c_pcie4: i2c at 1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c_riser1: i2c at 2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c_ocp: i2c at 3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&i2c8 {
+ status = "okay";
+
+ eeprom at 57 {
+ compatible = "atmel,24c256";
+ reg = <0x57>;
+ pagesize = <16>;
+ };
+};
+
+&i2c9 {
+ status = "okay";
+};
+
+&i2c10 {
+ status = "okay";
+};
+
+&i2c11 {
+ status = "okay";
+};
+
+&i2c12 {
+ status = "okay";
+};
+
+/*
+ * Enable port A as device (via the virtual hub) and port B as
+ * host by default on the eval board. This can be easily changed
+ * by replacing the override below with &ehci0 { ... } to enable
+ * host on both ports.
+ */
+&vhub {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&uhci {
+ status = "okay";
+};
+
+&gfx {
+ status = "okay";
+ memory-region = <&gfx_memory>;
+};
+
+&pwm_tacho {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_default
+ &pinctrl_pwm1_default
+ &pinctrl_pwm2_default
+ &pinctrl_pwm3_default
+ &pinctrl_pwm4_default
+ &pinctrl_pwm5_default
+ &pinctrl_pwm6_default>;
+
+ fan at 0 {
+ reg = <0x00>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+ };
+
+ fan at 1 {
+ reg = <0x00>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+ };
+
+ fan at 2 {
+ reg = <0x01>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+ };
+
+ fan at 3 {
+ reg = <0x01>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+ };
+
+ fan at 4 {
+ reg = <0x02>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+ };
+
+ fan at 5 {
+ reg = <0x02>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+ };
+
+ fan at 6 {
+ reg = <0x03>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+ };
+
+ fan at 7 {
+ reg = <0x03>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+ };
+
+ fan at 8 {
+ reg = <0x04>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x08>;
+ };
+
+ fan at 9 {
+ reg = <0x04>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x09>;
+ };
+
+ fan at 10 {
+ reg = <0x05>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
+ };
+
+ fan at 11 {
+ reg = <0x05>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
+ };
+
+ fan at 12 {
+ reg = <0x06>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
+ };
+
+ fan at 13 {
+ reg = <0x06>;
+ aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
+ };
+};
+
+&gpio {
+
+ pin_gpio_a0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(A, 0) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "MAC1_INT_N";
+ };
+
+ pin_gpio_a1 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(A, 1) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "MEZZ_C_PRESENT_N";
+ };
+
+ pin_gpio_a2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(A, 2) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "PSU1_PRST";
+ };
+
+ pin_gpio_a3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(A, 3) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "PSU2_PRST";
+ };
+
+ pin_gpio_b5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "IRQ_BMC_PCH_SMI_LPC_N";
+ };
+
+ pin_gpio_f0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "IRQ_BMC_PCH_NMI_R";
+ };
+
+ pin_gpio_f1 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 1) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "FM_CPU1_DISABLE_COD_N";
+ };
+
+ pin_gpio_f2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 2) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "SMB_LAN_ALERT_N_MEZZ";
+ };
+
+ pin_gpio_f3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_BUS0_RST_OUT_N";
+ };
+
+ pin_gpio_f4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "FM_SKT0_FAULT_LED";
+ };
+
+ pin_gpio_f5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "FM_SKT1_FAULT_LED";
+ };
+
+ pin_gpio_f6 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 6) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "IRQ_BMC_CPLD_NMI";
+ };
+
+ pin_gpio_f7 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(F, 7) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "PSU2_ALERT_N";
+ };
+
+ pin_gpio_g0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 0) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "FM_CPU_ERR2_LVT3_N";
+ };
+
+ pin_gpio_g1 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 1) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "FM_CPU_MSMI_CATERR_LVT3_N";
+ };
+
+ pin_gpio_g2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 2) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "FM_PCH_BMC_THERMTRIP_N";
+ };
+
+ pin_gpio_g3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 3) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "BMC_I2C_BUS7_INT_N";
+ };
+
+ pin_gpio_g4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "FAN_PWR_CTL_N";
+ };
+
+ pin_gpio_g5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "NFC_FD_N";
+ };
+
+ pin_gpio_g6 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "IRQ_NMI_EVENT_N";
+ };
+
+ pin_gpio_g7 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(G, 7) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "RST_BMC_PCIE_I2CMUX_N";
+ };
+
+ pin_gpio_h0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "PSU1_EPOW_N_R";
+ };
+
+ pin_gpio_h1 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "PSU2_EPOW_N_R";
+ };
+
+ pin_gpio_h2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "PSU1_FFS_N_R";
+ };
+
+ pin_gpio_h3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "PSU2_FFS_N_R";
+ };
+
+ pin_gpio_h4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "PSU1_THROTTLE_N_R";
+ };
+
+ pin_gpio_h5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "PSU2_THROTTLE_N_R";
+ };
+
+ pin_gpio_h6 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 6) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "PSU1_SMB_RESET_N";
+ };
+
+ pin_gpio_h7 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "PSU2_SMB_RESET_N";
+ };
+
+ pin_gpio_i1 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(I, 1) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "FP_PWR_BTN_N";
+ };
+
+ pin_gpio_i2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(I, 2) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "BIOS_RCVR_N";
+ };
+
+ pin_gpio_i3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "BMC_INTRUDED_COVER";
+ };
+
+ pin_gpio_j2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "BMC_BIOS_UPDATE_N";
+ };
+
+ pin_gpio_j3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(J, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "RST_BMC_HDD_I2CMUX_N";
+ };
+
+ pin_gpio_q4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Q, 4) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "MEZZ_A_PRESENT_N";
+ };
+
+ pin_gpio_q5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Q, 5) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "VGA_FRONT_PRES_N";
+ };
+
+ pin_gpio_q6 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Q, 6) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "I2C_RISER1_INT_N";
+ };
+
+ pin_gpio_q7 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "NCSI_CABLE_DET_N";
+ };
+
+ pin_gpio_r0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "FP_RST_BTN_N";
+ };
+
+ pin_gpio_r2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "HDDSIG1_DETECT_N";
+ };
+
+ pin_gpio_r3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "HDDSIG2_DETECT_N";
+ };
+
+ pin_gpio_r4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(R, 4) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "HDDSIG3_DETECT_N";
+ };
+
+ pin_gpio_r5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(R, 5) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "VIDEO_CABLE_DETECT_N";
+ };
+
+ pin_gpio_s0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 0) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "BMC_PS_RAPIDON_WAKE_R_N";
+ };
+
+ pin_gpio_s1 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 1) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "HOST_TPM_PP_BUF";
+ };
+
+ pin_gpio_s2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "BMC_VGA_SW";
+ };
+
+ pin_gpio_s3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 3) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "IRQ_SML0_ALERT_MUX_N";
+ };
+
+ pin_gpio_s4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 4) GPIO_ACTIVE_HIGH>;
+ output;
+ line-name = "VBAT_EN_N";
+ };
+
+ pin_gpio_s5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 5) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "BMC_HW_STRAP_4";
+ };
+
+ pin_gpio_s6 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 6) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "PU_BMC_GPIOS6";
+ };
+
+ pin_gpio_s7 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "I2C_BUS7_RESET_N";
+ };
+
+ pin_gpio_y0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Y, 0) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "BMC_NCSI_MUX_CTL_S0";
+ };
+
+ pin_gpio_y1 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Y, 1) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "BMC_NCSI_MUX_CTL_S1";
+ };
+
+ pin_gpio_y2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Y, 2) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "UID_ALERT_N";
+ };
+
+ pin_gpio_z0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 0) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_RISER2_INT_N";
+ };
+
+ pin_gpio_z2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_RISER2_RESET_N";
+ };
+
+ pin_gpio_z3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "FM_BMC_PCH_SCI_LPC_N";
+ };
+
+ pin_gpio_z4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "BMC_HW_STRAP_17";
+ };
+
+ pin_gpio_z6 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 6) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "BMC_HW_STRAP_20";
+ };
+
+ pin_gpio_z7 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(Z, 7) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "BMC_POST_CMPLT_N";
+ };
+
+ pin_gpio_aa0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "HOST_BMC_USB_SEL";
+ };
+
+ pin_gpio_aa1 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 1) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "PSU1_ALERT_N";
+ };
+
+ pin_gpio_aa2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 2) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "FM_PVCCIN_CPU0_PWR_IN_ALERT_N";
+ };
+
+ pin_gpio_aa3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 3) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "FM_PVCCIN_CPU1_PWR_IN_ALERT_N";
+ };
+
+ pin_gpio_aa4 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 4) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "USB_CABLE_DETECT_N";
+ };
+
+ pin_gpio_aa5 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 5) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "I2C_BUS1_RST_OUT_N";
+ };
+
+ pin_gpio_aa6 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 6) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "IRQ_SMI_ACTIVE_N";
+ };
+
+ pin_gpio_aa7 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AA, 7) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "FM_BIOS_POST_CMPLT_N";
+ };
+
+ pin_gpio_ab0 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AB, 0) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "FM_TPM_MOD_PRES_N";
+ };
+
+ pin_gpio_ab1 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AB, 1) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "FORCE_NMI_SW_FPGA_N";
+ };
+
+ pin_gpio_ab2 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AB, 2) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "1U_2U_PCBA_SEL_R";
+ };
+
+ pin_gpio_ab3 {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(AB, 3) GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "INTRUDED_PRES_N";
+ };
+};
--
2.7.4
More information about the Linux-aspeed
mailing list