[PATCH v4 2/2] media: platform: Add Aspeed Video Engine driver
Hans Verkuil
hverkuil at xs4all.nl
Fri Nov 9 21:54:54 AEDT 2018
Hi Eddie,
Sorry for the delay, I've been away for the past two weeks and I've been
catching up ever since I came back.
On 11/08/18 16:48, Eddie James wrote:
>
>
> On 10/19/2018 03:26 PM, Eddie James wrote:
>>
>>
>> On 10/12/2018 07:22 AM, Hans Verkuil wrote:
>>> On 10/05/2018 09:57 PM, Eddie James wrote:
>>>> The Video Engine (VE) embedded in the Aspeed AST2400 and AST2500 SOCs
>>>> can capture and compress video data from digital or analog sources.
>>>> With
>>>> the Aspeed chip acting a service processor, the Video Engine can
>>>> capture
>>>> the host processor graphics output.
>>>>
>>>> Add a V4L2 driver to capture video data and compress it to JPEG images.
>>>> Make the video frames available through the V4L2 streaming interface.
>>>>
>>>> Signed-off-by: Eddie James <eajames at linux.ibm.com>
>>>> ---
>>>> MAINTAINERS | 8 +
>>>> drivers/media/platform/Kconfig | 8 +
>>>> drivers/media/platform/Makefile | 1 +
>>>> drivers/media/platform/aspeed-video.c | 1674
>>>> +++++++++++++++++++++++++++++++++
>>>> 4 files changed, 1691 insertions(+)
>>>> create mode 100644 drivers/media/platform/aspeed-video.c
>>>>
>>> <snip>
>>>
>>>> +static int aspeed_video_enum_input(struct file *file, void *fh,
>>>> + struct v4l2_input *inp)
>>>> +{
>>>> + if (inp->index)
>>>> + return -EINVAL;
>>>> +
>>>> + strscpy(inp->name, "Host VGA capture", sizeof(inp->name));
>>>> + inp->type = V4L2_INPUT_TYPE_CAMERA;
>>>> + inp->capabilities = V4L2_IN_CAP_DV_TIMINGS;
>>>> + inp->status = V4L2_IN_ST_NO_SIGNAL | V4L2_IN_ST_NO_SYNC;
>>> This can't be right. If there is a valid signal, then status should
>>> be 0.
>>> And ideally you can tell the difference between no signal and no sync
>>> as well.
>>>
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int aspeed_video_get_input(struct file *file, void *fh,
>>>> unsigned int *i)
>>>> +{
>>>> + *i = 0;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int aspeed_video_set_input(struct file *file, void *fh,
>>>> unsigned int i)
>>>> +{
>>>> + if (i)
>>>> + return -EINVAL;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int aspeed_video_get_parm(struct file *file, void *fh,
>>>> + struct v4l2_streamparm *a)
>>>> +{
>>>> + struct aspeed_video *video = video_drvdata(file);
>>>> +
>>>> + a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
>>>> + a->parm.capture.readbuffers = 3;
>>>> + a->parm.capture.timeperframe.numerator = 1;
>>>> + if (!video->frame_rate)
>>>> + a->parm.capture.timeperframe.denominator = MAX_FRAME_RATE + 1;
>>>> + else
>>>> + a->parm.capture.timeperframe.denominator = video->frame_rate;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int aspeed_video_set_parm(struct file *file, void *fh,
>>>> + struct v4l2_streamparm *a)
>>>> +{
>>>> + unsigned int frame_rate = 0;
>>>> + struct aspeed_video *video = video_drvdata(file);
>>>> +
>>>> + a->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
>>>> + a->parm.capture.readbuffers = 3;
>>>> +
>>>> + if (a->parm.capture.timeperframe.numerator)
>>>> + frame_rate = a->parm.capture.timeperframe.denominator /
>>>> + a->parm.capture.timeperframe.numerator;
>>>> +
>>>> + if (!frame_rate || frame_rate > MAX_FRAME_RATE) {
>>>> + frame_rate = 0;
>>>> +
>>>> + /*
>>>> + * Set to max + 1 to differentiate between max and 0, which
>>>> + * means "don't care".
>>> But what does "don't care" mean in practice? It's still not clear to
>>> me how this
>>> is supposed to work.
>>>
>>>> + */
>>>> + a->parm.capture.timeperframe.denominator = MAX_FRAME_RATE + 1;
>>> And regardless of anything else this timeperframe is out of the range
>>> that
>>> aspeed_video_enum_frameintervals() returns.
>>>
>>>> + a->parm.capture.timeperframe.numerator = 1;
>>>> + }
>>>> +
>>>> + if (video->frame_rate != frame_rate) {
>>>> + video->frame_rate = frame_rate;
>>>> + aspeed_video_update(video, VE_CTRL, VE_CTRL_FRC,
>>>> + FIELD_PREP(VE_CTRL_FRC, frame_rate));
>>>> + }
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int aspeed_video_enum_framesizes(struct file *file, void *fh,
>>>> + struct v4l2_frmsizeenum *fsize)
>>>> +{
>>>> + struct aspeed_video *video = video_drvdata(file);
>>>> +
>>>> + if (fsize->index)
>>>> + return -EINVAL;
>>>> +
>>>> + if (fsize->pixel_format != V4L2_PIX_FMT_JPEG)
>>>> + return -EINVAL;
>>>> +
>>>> + fsize->discrete.width = video->pix_fmt.width;
>>>> + fsize->discrete.height = video->pix_fmt.height;
>>>> + fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int aspeed_video_enum_frameintervals(struct file *file, void
>>>> *fh,
>>>> + struct v4l2_frmivalenum *fival)
>>>> +{
>>>> + struct aspeed_video *video = video_drvdata(file);
>>>> +
>>>> + if (fival->index)
>>>> + return -EINVAL;
>>>> +
>>>> + if (fival->width != video->width || fival->height !=
>>>> video->height)
>>>> + return -EINVAL;
>>>> +
>>>> + if (fival->pixel_format != V4L2_PIX_FMT_JPEG)
>>>> + return -EINVAL;
>>>> +
>>>> + fival->type = V4L2_FRMIVAL_TYPE_CONTINUOUS;
>>>> +
>>>> + fival->stepwise.min.denominator = MAX_FRAME_RATE;
>>>> + fival->stepwise.min.numerator = 1;
>>>> + fival->stepwise.max.denominator = 1;
>>>> + fival->stepwise.max.numerator = 1;
>>>> + fival->stepwise.step = fival->stepwise.max;
>>>> +
>>>> + return 0;
>>>> +}
>>>> +
>>>> +static int aspeed_video_set_dv_timings(struct file *file, void *fh,
>>>> + struct v4l2_dv_timings *timings)
>>>> +{
>>>> + struct aspeed_video *video = video_drvdata(file);
>>>> +
>>> If vb2_is_busy() returns true, then return -EBUSY here. It is not
>>> allowed to
>>> set the timings while vb2 is busy.
>>
>> Buffer ioctls (Input 0):
>> fail: v4l2-test-buffers.cpp(344): node->s_dv_timings(timings)
>> fail: v4l2-test-buffers.cpp(452): testCanSetSameTimings(node)
>> test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: FAIL
>>
>> Streaming ioctls:
>> test read/write: OK
>> test blocking wait: OK
>> fail: v4l2-test-buffers.cpp(344): node->s_dv_timings(timings)
>> fail: v4l2-test-buffers.cpp(637): testCanSetSameTimings(node)
>> fail: v4l2-test-buffers.cpp(952): captureBufs(node, q, m2m_q,
>> frame_count, false)
>> test MMAP: FAIL
>>
>> Built from v4l-utils c36dbbdfa8b30b2badd4f893b59d0bd4f0bd12aa
>>
>> Adding this causes some of the v4l2-compliance streaming tests to
>> fail, and prevents my own application from being able to call
>> S_DV_TIMINGS after detecting a resolution change, despite calling
>> streamoff and unmapping all the buffers first.
>
> Any thoughts on this Hans?
The compliance fail is because there is a requirement that if you set
new timings that are equal to the existing timings, then that should
work (and is effectively a NOP operation).
So in the code you can do something similar to what vivid does:
if (v4l2_match_dv_timings(timings, &dev->dv_timings_cap, 0, false))
return 0;
if (vb2_is_busy(&dev->vb_vid_cap_q))
return -EBUSY;
You can probably get away with just checking width, height and interlaced
in this driver, rather than calling v4l2_match_dv_timings.
If the resolution changes, however, then you need to completely free all
buffers (i.e. close the fd or call VIDIOC_REQBUFS with count = 0) before
you can set new timings. So streamoff + unmap is not enough.
Streamoff only returns the buffers to userspace, it doesn't free them.
Regards,
Hans
More information about the Linux-aspeed
mailing list