[PATCH 6/6] ARM: dts: aspeed: Add Palmetto GPIO hogs

[Andrew Jeffery]

On Mon, 2018-02-12 at 18:13 +1030, Joel Stanley wrote:
> These hogs are for parts of the system that need to be in this state,
> but do not yet have a driver associated with them but they must be
> configured in order to successfully boot the host.
> 
> There are also some pinmux hogs, where the default mode of the IP block
> is configured.
> 
> Signed-off-by: Joel Stanley <joel at jms.id.au>

Acked-by: Andrew Jeffery <andrew at aj.id.au>

> ---
>  arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts | 157 ++++++++++++++++++++++++++
>  1 file changed, 157 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts b/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
> index 2a4a355a779d..bbddfe1d1cc8 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
> @@ -74,6 +74,14 @@
>  	};
>  };
>  
> +&pinctrl {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flbusy_default &pinctrl_flwp_default
> +
> +			&pinctrl_vgahs_default &pinctrl_vgavs_default
> +			&pinctrl_ddcclk_default &pinctrl_ddcdat_default>;
> +};
> +
>  &uart5 {
>  	status = "okay";
>  };
> @@ -142,3 +150,152 @@
>  &ibt {
>  	status = "okay";
>  };
> +
> +&gpio {
> +	pin_func_mode0 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(C, 4) GPIO_ACTIVE_HIGH>;
> +		output-low;
> +		line-name = "func_mode0";
> +	};
> +
> +	pin_func_mode1 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(C, 5)  GPIO_ACTIVE_HIGH>;
> +		output-low;
> +		line-name = "func_mode1";
> +	};
> +
> +	pin_func_mode2 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
> +		output-low;
> +		line-name = "func_mode2";
> +	};
> +
> +	pin_gpio_a0 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(A, 0) GPIO_ACTIVE_HIGH>;
> +		input;
> +		line-name = "BMC_FAN_RESERVED_N";
> +	};
> +
> +	pin_gpio_a1 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(A, 1) GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "APSS_WDT_N";
> +	};
> +
> +	pin_gpio_b1 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(B, 1) GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "APSS_BOOT_MODE";
> +	};
> +
> +	pin_gpio_b2 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(B, 2) GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "APSS_RESET_N";
> +	};
> +
> +	pin_gpio_b7 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(B, 7) GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "SPIVID_STBY_RESET_N";
> +	};
> +
> +	pin_gpio_d1 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(D, 1) GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "BMC_POWER_UP";
> +	};
> +
> +	pin_gpio_f1 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(F, 1) GPIO_ACTIVE_HIGH>;
> +		input;
> +		line-name = "BMC_BATTERY_TEST";
> +	};
> +
> +	pin_gpio_f4 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_HIGH>;
> +		input;
> +		line-name = "AST_HW_FAULT_N";
> +	};
> +
> +	pin_gpio_f5 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_HIGH>;
> +		input;
> +		line-name = "AST_SYS_FAULT_N";
> +	};
> +
> +	pin_gpio_f7 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(F, 7) GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "BMC_FULL_SPEED_N";
> +	};
> +
> +	pin_gpio_g3 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(G, 3) GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "BMC_FAN_ERROR_N";
> +	};
> +
> +	pin_gpio_g4 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>;
> +		input;
> +		line-name = "BMC_WDT_RST1_P";
> +	};
> +
> +	pin_gpio_g5 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
> +		input;
> +		line-name = "BMC_WDT_RST2_P";
> +	};
> +
> +	pin_gpio_h0 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
> +		input;
> +		line-name = "PE_SLOT_TEST_EN_N";
> +	};
> +
> +	pin_gpio_h1 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
> +		input;
> +		line-name = "BMC_RTCRST_N";
> +	};
> +
> +	pin_gpio_h2 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "SYS_PWROK_BMC";
> +	};
> +
> +	pin_gpio_h6 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(H, 6) GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "SCM1_FSI0_DATA_EN";
> +	};
> +
> +	pin_gpio_h7 {
> +		gpio-hog;
> +		gpios = <ASPEED_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
> +		output-high;
> +		line-name = "BMC_TPM_INT_N";
> +	};
> +};
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: This is a digitally signed message part
URL: <http://lists.ozlabs.org/pipermail/linux-aspeed/attachments/20180216/31d61e47/attachment.sig>