[PATCH v3 1/7] net: mv643xx_eth: add Device Tree bindings
Sebastian Hesselbarth
sebastian.hesselbarth at gmail.com
Tue May 21 07:34:40 EST 2013
On 05/20/2013 11:19 PM, Simon Baatz wrote:
> On Mon, May 06, 2013 at 05:33:34PM +0200, Sebastian Hesselbarth wrote:
>> From: Florian Fainelli<florian at openwrt.org>
>>
...
>> @@ -2485,13 +2499,21 @@ static int mv643xx_eth_shared_probe(struct platform_device *pdev)
>> if (dram)
>> mv643xx_eth_conf_mbus_windows(msp, dram);
>>
>> - msp->tx_csum_limit = (pd != NULL&& pd->tx_csum_limit) ?
>> - pd->tx_csum_limit : 9 * 1024;
>> + if (np)
>> + of_property_read_u32(np, "tx-csum-limit",&tx_csum_limit);
>> + else
>> + tx_csum_limit = pd->tx_csum_limit;
>> +
>> + msp->tx_csum_limit = tx_csum_limit ? tx_csum_limit : 9 * 1024;
>> infer_hw_params(msp);
>>
>> platform_set_drvdata(pdev, msp);
>>
>> +#ifdef CONFIG_OF
>> + return of_platform_bus_probe(np, mv643xx_eth_match,&pdev->dev);
>
> I have tested this on Kirkwood (Sheevaplug eSATA). When using
> mv643xx_eth as a module with a built-in mvmdio the GbE port works.
> However, when unloading the mv643xx_eth module and loading it again,
> the second call to of_platform_bus_probe() results in a warning:
>
> [ 190.542992] WARNING: at fs/sysfs/dir.c:530 sysfs_add_one+0x7c/0xa4()
> [ 190.549372] sysfs: cannot create duplicate filename '/devices/ocp.0/f1072000.
> ethernet-controller/0.ethernet-port'
>
> (Looks more like a problem of of_platform_bus_probe() than a problem
> in the driver?)
Hi Simon,
thanks for the review. I am right now working on a v4 of the DT support
patches for mv643xx_eth and the above will not be there anymore. I will
test v4 for rmmod/modprobe issues before posting.
>> @@ -2677,6 +2769,10 @@ static int mv643xx_eth_probe(struct platform_device *pdev)
>> struct resource *res;
>> int err;
>>
>> + err = mv643xx_eth_of_probe(pdev);
>> + if (err)
>> + return err;
>> +
>> pd = pdev->dev.platform_data;
>> if (pd == NULL) {
>> dev_err(&pdev->dev, "no mv643xx_eth_platform_data\n");
>
> If the clock isn't already enabled (mvmdio and mv643xx_eth both built
> as modules), a delay seems to be necessary in mv643xx_eth_probe()
> after enabling the clock on my hardware. Otherwise the device hangs.
> Andrew found the same in the past (see [1]). udelay(50) seems to be
> sufficient in my case.
Hmm, I am wondering if that delay shouldn't be in the clock provider
then. I test it on Dove also and look for a way to insert the delay
if neccessary. Maybe Andrew can also comment on this.
>> @@ -2717,7 +2813,12 @@ static int mv643xx_eth_probe(struct platform_device *pdev)
>> netif_set_real_num_rx_queues(dev, mp->rxq_count);
>>
>> if (pd->phy_addr != MV643XX_ETH_PHY_NONE) {
>> - mp->phy = phy_scan(mp, pd->phy_addr);
>> + if (pd->phy_node)
>> + mp->phy = of_phy_connect(mp->dev, pd->phy_node,
>> + mv643xx_eth_adjust_link, 0,
>> + PHY_INTERFACE_MODE_GMII);
>
> of_phy_connect() returns NULL in case of an error and no ERR_PTR.
True, will take care of that.
Sebastian
More information about the devicetree-discuss
mailing list