[PATCH] Documentation: dt: bindings: TI WiLink modules

[Felipe Balbi]

On Fri, Jun 28, 2013 at 03:13:52PM +0300, Luciano Coelho wrote:
> On Fri, 2013-06-28 at 14:41 +0300, Felipe Balbi wrote:
> > On Fri, Jun 28, 2013 at 02:22:11PM +0300, Luciano Coelho wrote:
> > > On Fri, 2013-06-28 at 13:31 +0300, Luciano Coelho wrote:
> > > > (fixed Mike's address)
> > > > 
> > > > On Fri, 2013-06-28 at 11:21 +0100, Mark Rutland wrote:
> > > > > On Fri, Jun 28, 2013 at 10:53:35AM +0100, Luciano Coelho wrote:
> > > > > > On Fri, 2013-06-28 at 10:38 +0100, Mark Rutland wrote:
> > > > > > > On Tue, Jun 25, 2013 at 09:35:30AM +0100, Luciano Coelho wrote:
> > > > > > > > +Optional properties:
> > > > > > > > +--------------------
> > > > > > > > +
> > > > > > > > +- refclock: the internal WLAN reference clock frequency (required for
> > > > > > > > +  WiLink6 and WiLink7; not used for WiLink8).  Must be one of the
> > > > > > > > +  following:
> > > > > > > > +	0 = 19.2 MHz
> > > > > > > > +	1 = 26.0 MHz
> > > > > > > > +	2 = 38.4 MHz
> > > > > > > > +	3 = 52.0 MHz
> > > > > > > > +	4 = 38.4 MHz, XTAL
> > > > > > > > +	5 = 26.0 MHz, XTAL
> > > > > > > > +
> > > > > > > > +- tcxoclock: the internal WLAN TCXO clock frequency (required for
> > > > > > > > +  WiLink7 not used for WiLink6 and WiLink8).  Must be one of the
> > > > > > > > +  following:
> > > > > > > > +	0 = 19.200 MHz
> > > > > > > > +	1 = 26.000 MHz
> > > > > > > > +	2 = 38.400 MHz
> > > > > > > > +	3 = 52.000 MHz
> > > > > > > > +	4 = 16.368 MHz
> > > > > > > > +	5 = 32.736 MHz
> > > > > > > > +	6 = 16.800 MHz
> > > > > > > > +	7 = 33.600 MHz
> > > > > > > 
> > > > > > > This looks suspiciously like what we have the common clock bindings for:
> > > > > > > 
> > > > > > > refclk {
> > > > > > > 	compatible = "fixed-clock";
> > > > > > > 	#clock-cells = <0>;
> > > > > > > 	clock-frequency = <19200000>;
> > > > > > > }
> > > > > > > 
> > > > > > > wilink {
> > > > > > > 	compatible = "ti,wilink7";
> > > > > > > 	interrupt-parent = <&some_interrupt_controller>;
> > > > > > > 	interrupts = <0 1 1>;
> > > > > > > 	clocks = <&refclk>, <&refclk>;
> > > > > > > 	clock-names = "refclk", "txoclk";
> > > > > > > };
> > > > > > > 
> > > > > > > Could you not use them?
> > > > > > 
> > > > > > Hmmm... this actually does look good.  But these are internal clocks in
> > > > > > the modules, they cannot be accessed from outside.  Does it make sense
> > > > > > to register them with the clock framework?
> > > > > 
> > > > > Given we already have a common way of describing clocks, I think it
> > > > > makes sense to use it -- people already understand the common bindings,
> > > > > and it's less code to add add to the kernel. I don't think the fact
> > > > > these clocks are internal should prevent us from describing them as we
> > > > > would an external clock.
> > > > 
> > > > Yes, I agree with you.  Thanks for the suggestion! I think it will look
> > > > much better.  And now that I dug a bit more into the code, I can see
> > > > that there are only structs being populated, so there shouldn't be any
> > > > other side-effects.
> > > 
> > > Hmmm, one thing that escaped me.  Besides the frequency, I also need a
> > > boolean that tells if the clock is XTAL or not.  I can't figure out how
> > > to pass this if I use the generic clock framework.  Any suggestions?
> > 
> > Could you use clock-output-names for that ?
> > 
> > XTAL clock:
> > 
> > refclk {
> > 	compatible = "fixed-clock";
> > 	#clock cells = <0>;
> > 	clock-frequency = <19200000>;
> > 	clock-output-names = "xtal";
> > };
> > 
> > non-XTAL clock:
> > 
> > refclk {
> > 	compatible = "fixed-clock";
> > 	#clock cells = <0>;
> > 	clock-frequency = <19200000>;
> > 	clock-output-names = "osc"; /* any better name ? */
> > };
> 
> This starts looking a bit hacky.  Using the output name as a flag is not
> very pretty.
> 
> I think it would be better to have a separate flag for it in the wlan
> node.  Like an optional "refclock-xtal" boolean or something.  The
> downside of this is that we would be adding information about the clock
> details in the wilink node. :(
> 
> OTOH, we could add a flag to the generic clock binding? A new optional
> boolean that tells whether the clock is XTAL or not:
> 
> refclk {
> 	compatible = "fixed-clock";
> 	#clock cells = <0>;
> 	clock-frequency = <19200000>;
> 	clock-xtal;
> };
> 
> Do you think that would make sense?

sure, that looks alright to me. Surely there are other devices out there
who want to know if the clock comes from a crystal or not ?!?

cheers

-- 
balbi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.ozlabs.org/pipermail/devicetree-discuss/attachments/20130628/3b2fecea/attachment-0001.sig>