[PATCH 2/2] regulator: palmas: model SMPS10 as two regulators

[Kishon Vijay Abraham I]

Hi,

On Thursday 20 June 2013 07:33 PM, Laxman Dewangan wrote:
> On Thursday 20 June 2013 07:20 PM, Kishon Vijay Abraham I wrote:
>> Hi,
>>
>> On Thursday 20 June 2013 04:22 PM, Laxman Dewangan wrote:
>>> On Thursday 20 June 2013 02:07 PM, Kishon Vijay Abraham I wrote:
>>>> SMPS10 has two outputs OUT1 and OUT2 and have one input IN1.
>>>> SMPS10-OUT2 is connected to SMPS10-IN1 and can be configured either
>>>> in BOOST mode or BYPASS mode. regulator_enable of SMPS10-OUT2 configures
>>>> it in BOOST mode. For BYPASS mode regulator_allow_bypass() API can be
>>>> used. SMPS10-OUT1 is connected to SMPS10-OUT2 and can be enabled using
>>>> regulator_enable().
>>>>
>>>> Cc: Laxman Dewangan <ldewangan at nvidia.com>
>>>> Signed-off-by: Kishon Vijay Abraham I <kishon at ti.com>
>>>> ---
>>>>    drivers/regulator/palmas-regulator.c |   39
>>>> ++++++++++++++++++++++++++++++----
>>>>    include/linux/mfd/palmas.h           |    9 ++++----
>>>>    2 files changed, 40 insertions(+), 8 deletions(-)
>>>>
>>>> diff --git a/drivers/regulator/palmas-regulator.c
>>>> b/drivers/regulator/palmas-regulator.c
>>>> index 3ae44ac..7004bab 100644
>>>> --- a/drivers/regulator/palmas-regulator.c
>>>> +++ b/drivers/regulator/palmas-regulator.c
>>>> @@ -97,7 +97,12 @@ static const struct regs_info palmas_regs_info[] = {
>>>>            .ctrl_addr    = PALMAS_SMPS9_CTRL,
>>>>        },
>>>>        {
>>>> -        .name        = "SMPS10",
>>>> +        .name        = "SMPS10_OUT1",
>>>> +        .sname        = "smps10-out2",
>>>> +        .ctrl_addr    = PALMAS_SMPS10_CTRL,
>>>> +    },
>>>> +    {
>>>> +        .name        = "SMPS10_OUT2",
>>>>            .sname        = "smps10-in",
>>>>
>>> This sequence can create regulator to be never register.
>>> In probe, we register regulator from 0 to max_id.
>>> Here smps10-out1 comes first and see the supply as smps10-out2 which is not
>>> registered yet and so will fail with PROBE_DEFER
>>> When again it tries, the same issue.
>> hmm.. But I was able to get (regulator_get) *SMPS10_OUT1* without any issue
>> during my testing. From looking at the code, I couldn't see *sname* being used
>> anywhere.
>
> We used the sname as
> pmic->desc[id].supply_name = palmas_regs_info[id].sname;
>
> However, how you have populated your dt?
> Have you added like
> smps10-out2-supply = <&SMPS10_OUT2>
>
> for the palmas regualtor -dt.

I added the regulator data like

+                       smps10_out1_reg: smps10_out1 {
+                               regulator-name = "smps10_out1";
+                               regulator-min-microvolt = <5000000>;
+                               regulator-max-microvolt = <5000000>;
+                               regulator-always-on;
+                               regulator-boot-on;
+                               regulator-allow-bypass;
+                               ti,warm_sleep = <0>;
+                               ti,roof_floor = <0>;
+                               ti,mode_sleep = <0>;
+                               ti,warm_reset = <0>;
+                               ti,tstep = <0>;
+                               ti,vsel = <0>;
+                       };

and from my controller I reference it using
+               vbus-supply = <&smps10_out1_reg>;

and in the controller driver I use
+               vbus_reg = devm_regulator_get(dev, "vbus");

Thanks
Kishon