[PATCH V4 1/3] pci: Add PCIe driver for Samsung Exynos

[Jingoo Han]

On Thursday, June 20, 2013 8:26 PM, Pratyush Anand wrote:
> On 6/20/2013 4:28 PM, Jingoo Han wrote:
> > On Thursday, June 20, 2013 6:59 PM, Pratyush Anand wrote:
> >> On 6/13/2013 7:48 PM, Arnd Bergmann wrote:
> >>> On Thursday 13 June 2013 22:18:50 Jingoo Han wrote:
> >>>>> On Wednesday, June 12, 2013 8:23 PM, Arnd Bergmann wrote:
> >>>>>>> On Wednesday 12 June 2013 19:19:05 Jingoo Han wrote:
> >>>>>>>>> +
> >>>>>>>>> +/* synopsis specific PCIE configuration registers*/
> >>>>>>>>> +#define PCIE_PORT_LINK_CONTROL		0x710
> >>>>>>>>> +#define PORT_LINK_MODE_MASK		(0x3f << 16)
> >>>>>>>>> +#define PORT_LINK_MODE_4_LANES		(0x7 << 16)
> >>>>>>>
> >>>>>>> Do you mean this is a "Synopsys" designware part? In that case it
> >>>>>>> should really not be called "exynos-pcie" but "designware-pcie"
> >>>>>>> and you should make sure that the driver makes no assumptions about
> >>>>>>> the platform. A lot of other platforms also use designware
> >>>>>>> parts and should be able to reuse this driver.
> >>>>>
> >>>>> Sorry, I don't think so.
> >>>>> Only core block is a "Synopsys" designware part IP block,
> >>>>> other parts are Exynos-specific.
> >>>>> So, it is hard to share with other PCIe IPs using synopsis core.
> >>> Just call it synopsys anyway and put a comment in to explain this.
> >>> That should be enough for the next person with a synopsys PCI core
> >>> to reuse your code and split out the exynos specific parts into a
> >>> separate file.
> >>>
> >>
> >> I agree to Arnd that this patch should be split. I had worked in past
> >> with SPEAr PCIe which also had designware PCIe IP. I see some code which
> >> will fit both in SPEAr as well as in exynos. Unfortunately, I was not
> >> able to get SPEAr driver pushed to mainline, as I moved to some other
> >> project and got heavily occupied.
> >
> > Oh, I see.
> >
> > How about this?
> > At the next PATCH v7, I will change the file name from 'pci-exynos.c'
> > to 'pci-designware.c', as Arnd mentioned.
> >
> > Then, when Spear or other platform using designware is submitted,
> > this 'pci-designware.c' will be split to two separate files such as
> > 'pci-designware.c' and 'pci-exynos.c'.
> >
> 
> For me it's OK. Let it go to mainline as Arnd mentioned.
> Please keep Mohit in mail chain, who might have some bandwidth to
> further add and follow up for SPEAr on top of your patches.

Dear Pratyush Anand,

Thank you for accepting the suggestion. :)
OK, I will keep Mohit in main chain.


Best regards,
Jingoo Han

> 
> Regards
> Pratyush
> 
> >
> > Best regards,
> > Jingoo Han
> >
> >>
> >> Last patch is here:
> >>
> >> https://patchwork.kernel.org/patch/1661441/
> >>
> >> Infact, these functions should be common to all arm platforms.
> >>
> >> sys_to_pcie
> >> cfg_read
> >> cfg_write
> >>
> >> Following functions should be common to all designware based driver (at
> >> least they are same in SPEAr)
> >>
> >> exynos_pcie_prog_viewport_cfg0
> >> exynos_pcie_prog_viewport_cfg1
> >> exynos_pcie_rd_other_conf
> >> exynos_pcie_wr_other_conf
> >> exynos_pcie_setup
> >> exynos_pcie_valid_config
> >> exynos_pcie_rd_conf
> >> exynos_pcie_wd_conf
> >> exynos_pcie_scan_bus
> >> exynos_pcie_map_irq
> >> add_pcie_port (after a bit of generalization)
> >> exynos_pcie_probe
> >> exynos_pcie_remove
> >>
> >>
> >>
> >> Following should be specific to exynos:
> >>
> >> exynos_pcie_rd_own_conf
> >> exynos_pcie_wr_own_conf
> >> exynos_pcie_link_up
> >> exynos_pcie_setup_rc
> >> exynos_pcie_assert_core_reset
> >> exynos_pcie_deassert_core_reset
> >> exynos_pcie_assert_phy_reset
> >> exynos_pcie_deassert_phy_reset
> >> exynos_pcie_init_phy
> >> exynos_pcie_assert_reset
> >> exynos_pcie_establish_link
> >> exynos_pcie_host_init
> >>
> >>
> >>
> >> struct pcie_port_info and struct pcie_port can also be standardized.
> >>
> >> Regards
> >> Pratyush
> >
> > .
> >