[PATCH v3 11/12] ARM: mvebu: Relocate Armada 370 PCIe device tree nodes

Arnd Bergmann arnd at arndb.de
Wed Jun 19 02:29:35 EST 2013


On Tuesday 18 June 2013, Ezequiel Garcia wrote:
> +                       ranges =
> +                              <0x82000000 0 0x40000    0xffff0001 0x40000 0 0x00002000
> +                               0x82000000 0 0x80000    0xffff0001 0x80000 0 0x00002000
> +                               0x82000000 0 0xe0000000 0xffff0002 0          0 0x08000000
> +                               0x81000000 0 0          0xffff0002 0x8000000  0 0x00100000>;

To clarify my earlier comment, I think it would be nicer to write this as

                       ranges =
                              <0x82000000 0 0x40000    0xffff0001 0x40000 0 0x00002000
                               0x82000000 0 0x80000    0xffff0001 0x80000 0 0x00002000
                               0x82000000 1 0 MBUS_ID(0x12, 0x34) 0  1 0
                               0x82000000 2 0 MBUS_ID(0x13, 0x34) 0  1 0
                               0x81000000 1 0 MBUS_ID(0x12, 0x35) 0 0 0x10000;
                               0x81000000 2 0 MBUS_ID(0x13, 0x35) 0 0 0x10000>;

The MBUS_ID numbers above are made up since I don't know them, but this way you can
describe how the entire 4GB MMIO address space of the PCI bus is mapped into the
MBUS address space.

> +                       pcie at 1,0 {
> +                               device_type = "pci";
> +                               assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
> +                               reg = <0x0800 0 0 0 0>;
> +                               #address-cells = <3>;
> +                               #size-cells = <2>;
> +                               #interrupt-cells = <1>;
> +                               ranges;

Then you do a ranges property for each port with the high-order
address word equal to the port number:

                     ranges = <0x82000000 1 0 0x82000000 0 0 1 0
                               0x81000000 1 0 0x81000000 0 0 0 0x10000>;


> +                               interrupt-map-mask = <0 0 0 0>;
> +                               interrupt-map = <0 0 0 0 &mpic 58>;
> +                               marvell,pcie-port = <0>;
> +                               marvell,pcie-lane = <0>;
> +                               clocks = <&gateclk 5>;
> +                               status = "disabled";
> +                       pcie at 2,0 {
> +                               device_type = "pci";
> +                               assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
> +                               reg = <0x1000 0 0 0 0>;
> +                               #address-cells = <3>;
> +                               #size-cells = <2>;
> +                               #interrupt-cells = <1>;
> +                               ranges;

                     ranges = <0x82000000 2 0 0x82000000 0 0 1 0
                               0x81000000 2 0 0x81000000 0 0 0 0x10000>;

> +                               interrupt-map-mask = <0 0 0 0>;
> +                               interrupt-map = <0 0 0 0 &mpic 62>;
> +                               marvell,pcie-port = <1>;
> +                               marvell,pcie-lane = <0>;
> +                               clocks = <&gateclk 9>;
> +                               status = "disabled";
> +                       };

Does this make sense?

	Arnd


More information about the devicetree-discuss mailing list