[PATCH v2 1/4] ARM: dts: omap4-panda: Add USB Host support

[Roger Quadros]

Provide the RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.

Also provide pin multiplexer information for the USB host
pins.

Signed-off-by: Roger Quadros <rogerq at ti.com>
---
 arch/arm/boot/dts/omap4-panda-common.dtsi |   62 +++++++++++++++++++++++++++++
 1 files changed, 62 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index 00cbaa5..7a21e8e 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -59,6 +59,42 @@
 			"AFML", "Line In",
 			"AFMR", "Line In";
 	};
+
+	/* HS USB Port 1 RESET */
+	hsusb1_reset: hsusb1_reset_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "hsusb1_reset";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 30 0>;	/* gpio_62 */
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
+	/* HS USB Port 1 Power */
+	hsusb1_power: hsusb1_power_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "hsusb1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 1 0>;	/* gpio_1 */
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
+	/* HS USB Host PHY on PORT 1 */
+	hsusb1_phy: hsusb1_phy {
+		compatible = "usb-nop-xceiv";
+		reset-supply = <&hsusb1_reset>;
+		vcc-supply = <&hsusb1_power>;
+	/**
+	 * FIXME:
+	 * put the right clock phandle here when available
+	 *	clocks = <&auxclk3>;
+	 *	clock-names = "main_clk";
+	 */
+		clock-frequency = <19200000>;
+	};
 };
 
 &omap4_pmx_wkup {
@@ -83,6 +119,7 @@
 			&mcbsp1_pins
 			&dss_hdmi_pins
 			&tpd12s015_pins
+			&hsusbb1_pins
 	>;
 
 	twl6030_pins: pinmux_twl6030_pins {
@@ -133,6 +170,23 @@
 		>;
 	};
 
+	hsusbb1_pins: pinmux_hsusbb1_pins {
+		pinctrl-single,pins = <
+			0x82 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
+			0x84 (PIN_OUTPUT | MUX_MODE4)		/* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
+			0x86 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
+			0x88 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
+			0x8a (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
+			0x8c (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
+			0x8e (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
+			0x90 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
+			0x92 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
+			0x94 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
+			0x96 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
+			0x98 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
+		>;
+	};
+
 	i2c1_pins: pinmux_i2c1_pins {
 		pinctrl-single,pins = <
 			0xe2 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl */
@@ -283,3 +337,11 @@
 	mode = <3>;
 	power = <50>;
 };
+
+&usbhshost {
+	port1-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <&hsusb1_phy>;
+};
-- 
1.7.4.1