[PATCH v2 06/11] ARM:stixxxx: Add STiH415 SOC support

Srinivas KANDAGATLA srinivas.kandagatla at st.com
Tue Jun 11 02:38:54 EST 2013


On 10/06/13 13:43, Linus Walleij wrote:
> On Mon, Jun 10, 2013 at 11:26 AM, Srinivas KANDAGATLA
> <srinivas.kandagatla at st.com> wrote:
> 
>> The STiH415 is the next generation of HD, AVC set-top box processors for
>> satellite, cable, terrestrial and IP-STB markets. It is an ARM Cortex-A9
>> 1.0 GHz, dual-core CPU.
> (...)
>> +       soc {
>> +               pin-controller-sbc {
>> +                       #address-cells  = <1>;
>> +                       #size-cells     = <1>;
>> +                       compatible      = "st,stih415-pinctrl", "simple-bus";
> 
> Why is the pin controller be a simple bus?
As gpio banks are children of this node, the gpio driver associated with
these banks can only be probed if the parent of the node has simple bus
compatible string.

> 
> Maybe obvious, I'm not 100% familiar with when we use this...
> 
>> +               pin-controller-front {
> (...)
>> +               pin-controller-rear {
> (...)
>> +               pin-controller-left {
> (...)
>> +               pin-controller-right {
> 
> Please explain these orientations in some comment in the device
> tree, I'm half-guessing that it's about the edges around the chip so
> the PIO* names are actually pad names.
> 
> I would suggest you use the names north/south/west/east
> if this is the case since left and right etc are relative measures.
> (This terminology is used on e.g. dance mats for console games...)
> 
> If these names are from the datasheets by all means keep them.

I will add more comments in this area, the naming comes from
data-sheets. I have no choice.
> 
>> +++ b/arch/arm/boot/dts/stixxxx-pincfg.h
>> @@ -0,0 +1,94 @@
>> +#ifndef _STIXXXX_PINCFG_H_
>> +#define _STIXXXX_PINCFG_H_
>> +
>> +/* Alternate functions */
>> +#define ALT1   1
>> +#define ALT2   2
>> +#define ALT3   3
>> +#define ALT4   4
>> +#define ALT5   5
>> +#define ALT6   6
>> +#define ALT7   7
> 
> Why is this part of the DT definitions? In the pinctrl world this
> is an intrinsic detail on how groups and functions are associated,
> not something that you hard-code into the device tree. The
> device tree should state how to combine functions with groups
> and those will be strings, not numerals.
If this is wrong way to do things, I would like to fix this.
Functions in ST are alt-functions which are generally from alt0-alt7.
I use this property in the pinctrl group as shown in this simple example:

pinctrl_sbc_serial1:sbc_serial1 {
       st,function = <ALT3>;
       st,pins {
              tx      = <&PIO2 6 OUT>;
              rx      = <&PIO2 7 IN>;
       };
};

To configure the group in alternate function 3.
You suggest that this should be
st,function = "alt3"; it does not look any different to what I have.

Looking at some of existing pinctrl nodes, I can see like:
                samsung,pin-function = <2>;
or
		brcm,function = <4>; /* alt0 */

Sorry ...Am I missing some thing?

Thanks,
srini
> 
> Yours,
> Linus Walleij
> 



More information about the devicetree-discuss mailing list