[PATCH] arm: dts: omap4-sdp: Add I2c pinctrl data

Kumar, Anil anilkumar.v at ti.com
Thu Jan 31 13:32:27 EST 2013


On Wed, Jan 30, 2013 at 14:36:10, Coelho, Luciano wrote:
> On Wed, 2013-01-30 at 14:18 +0530, Santosh Shilimkar wrote:
> > On Wednesday 30 January 2013 02:13 PM, Kumar, Anil wrote:
> > > Hi Sourav,
> > >
> > > On Wed, Jan 30, 2013 at 12:10:18, Poddar, Sourav wrote:
> > >> Hi Luciano,
> > >> On Wednesday 30 January 2013 11:55 AM, Luciano Coelho wrote:
> > >>> Hi Sourav,
> > >>>
> > >>> On Mon, 2013-01-28 at 16:47 +0530, Sourav Poddar wrote:
> > >>>> Booting 3.8-rc4 om omap 4430sdp results in the following error
> > >>>>
> > >>>> omap_i2c 48070000.i2c: did not get pins for i2c error: -19
> > >>>> [    1.024261] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz
> > >>>> [    1.030181] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
> > >>>> [    1.037384] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
> > >>>> [    1.043762] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
> > >>>> [    1.050964] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz
> > >>>> [    1.056823] omap_i2c 4807a000.i2c: did not get pins for i2c error: -19
> > >>>> [    1.064025] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
> > >>>>
> > >>>> This happens because omap4 dts file is not adapted to use i2c through pinctrl
> > >>>> framework. Populating i2c pinctrl data to get rid of the error.
> > >>>>
> > >>>> Tested on omap4430 sdp with 3.8-rc4 kernel.
> > >>>>
> > >>>> Signed-off-by: Sourav Poddar <sourav.poddar at ti.com>
> > >>>> Reported-by: Santosh Shilimkar <santosh.shilimkar at ti.com>
> > >>>> ---
> > >>> Could you do the same thing for panda? I'm getting the same kind of
> > >>> errors with it:
> > >
> > > omap4 uses pinctrl-single driver for pinmux with DT. Currently
> > > pinctrl-single driver is getting up after I2C driver. So I2c cannot
> > > use pinctrl. The below patch solve this issue
> > >
> > > http://www.gossamer-threads.com/lists/linux/kernel/1669067
> > >
> > > Can you try with this ? it may solve it.
> > >
> > OMAP i2c driver already takes care of -EPROBE_DEFER. The issue
> > as you see from the log is not probe failure but missing the
> > pin information in DT blob. And thats what patch does.
> 
> Yes, Santosh is right.  I tried this patch, but it didn't fix the
> warnings.

Sorry, I misunderstood this issue.

Anil 



More information about the devicetree-discuss mailing list