[PATCH 4/4] drivers: usb: start using the control module driver
kishon
kishon at ti.com
Fri Jan 18 23:11:20 EST 2013
On Friday 18 January 2013 05:32 PM, Felipe Balbi wrote:
> Hi,
>
> On Fri, Jan 18, 2013 at 03:10:45PM +0530, Kishon Vijay Abraham I wrote:
>> Start using the control module driver for powering on the PHY and for
>> writing to the mailbox instead of writing to the control module
>> registers on their own.
>>
>> Signed-off-by: Kishon Vijay Abraham I <kishon at ti.com>
>> ---
>> Documentation/devicetree/bindings/usb/omap-usb.txt | 4 ++
>> Documentation/devicetree/bindings/usb/usb-phy.txt | 7 +--
>> arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 13 ----
>> drivers/usb/musb/Kconfig | 1 +
>> drivers/usb/musb/omap2430.c | 64 ++++++++------------
>> drivers/usb/musb/omap2430.h | 9 ---
>> drivers/usb/phy/Kconfig | 1 +
>> drivers/usb/phy/omap-usb2.c | 38 +++---------
>> include/linux/usb/omap_usb.h | 4 +-
>> 9 files changed, 42 insertions(+), 99 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
>> index ead6ba9..8bedbba 100644
>> --- a/Documentation/devicetree/bindings/usb/omap-usb.txt
>> +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
>> @@ -3,6 +3,9 @@ OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
>> OMAP MUSB GLUE
>> - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
>> - ti,hwmods : must be "usb_otg_hs"
>> + - ti,has_mailbox : to specify that omap uses an external mailbox
>> + (in control module) to communicate with the musb core during device connect
>> + and disconnect.
>> - multipoint : Should be "1" indicating the musb controller supports
>> multipoint. This is a MUSB configuration-specific setting.
>> - num_eps : Specifies the number of endpoints. This is also a
>> @@ -24,6 +27,7 @@ SOC specific device node entry
>> usb_otg_hs: usb_otg_hs at 4a0ab000 {
>> compatible = "ti,omap4-musb";
>> ti,hwmods = "usb_otg_hs";
>> + ti,has_mailbox;
>> multipoint = <1>;
>> num_eps = <16>;
>> ram_bits = <12>;
>> diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt
>> index 2466b6f..48761a2 100644
>> --- a/Documentation/devicetree/bindings/usb/usb-phy.txt
>> +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt
>> @@ -4,9 +4,7 @@ OMAP USB2 PHY
>>
>> Required properties:
>> - compatible: Should be "ti,omap-usb2"
>> - - reg : Address and length of the register set for the device. Also
>> -add the address of control module dev conf register until a driver for
>> -control module is added
>> + - reg : Address and length of the register set for the device.
>>
>> Optional properties:
>> - ctrl_module : phandle of the control module used by PHY driver to power on
>> @@ -16,7 +14,6 @@ This is usually a subnode of ocp2scp to which it is connected.
>>
>> usb2phy at 4a0ad080 {
>> compatible = "ti,omap-usb2";
>> - reg = <0x4a0ad080 0x58>,
>> - <0x4a002300 0x4>;
>> + reg = <0x4a0ad080 0x58>;
>> ctrl_module = <&omap_control_usb>;
>> };
>> diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
>> index 129d508..103f4ba 100644
>> --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
>> +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
>> @@ -2698,13 +2698,6 @@ static struct resource omap44xx_usb_phy_and_pll_addrs[] = {
>> .end = 0x4a0ae000,
>> .flags = IORESOURCE_MEM,
>> },
>> - {
>> - /* XXX: Remove this once control module driver is in place */
>> - .name = "ctrl_dev",
>> - .start = 0x4a002300,
>> - .end = 0x4a002303,
>> - .flags = IORESOURCE_MEM,
>> - },
>> { }
>> };
>>
>> @@ -6152,12 +6145,6 @@ static struct omap_hwmod_addr_space omap44xx_usb_otg_hs_addrs[] = {
>> .pa_end = 0x4a0ab7ff,
>> .flags = ADDR_TYPE_RT
>> },
>> - {
>> - /* XXX: Remove this once control module driver is in place */
>> - .pa_start = 0x4a00233c,
>> - .pa_end = 0x4a00233f,
>> - .flags = ADDR_TYPE_RT
>> - },
>> { }
>> };
>>
>> diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig
>> index 23a0b7f..de6e5ce 100644
>> --- a/drivers/usb/musb/Kconfig
>> +++ b/drivers/usb/musb/Kconfig
>> @@ -11,6 +11,7 @@ config USB_MUSB_HDRC
>> select NOP_USB_XCEIV if (SOC_TI81XX || SOC_AM33XX)
>> select TWL4030_USB if MACH_OMAP_3430SDP
>> select TWL6030_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA
>> + select OMAP_CONTROL_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA
>> select USB_OTG_UTILS
>> help
>> Say Y here if your system has a dual role high speed USB
>> diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
>> index da00af4..3e7ceef 100644
>> --- a/drivers/usb/musb/omap2430.c
>> +++ b/drivers/usb/musb/omap2430.c
>> @@ -37,6 +37,7 @@
>> #include <linux/err.h>
>> #include <linux/delay.h>
>> #include <linux/usb/musb-omap.h>
>> +#include <linux/usb/omap_control_usb.h>
>>
>> #include "musb_core.h"
>> #include "omap2430.h"
>> @@ -46,7 +47,7 @@ struct omap2430_glue {
>> struct platform_device *musb;
>> enum omap_musb_vbus_id_status status;
>> struct work_struct omap_musb_mailbox_work;
>> - u32 __iomem *control_otghs;
>> + struct device *control_otghs;
>> };
>> #define glue_to_musb(g) platform_get_drvdata(g->musb)
>>
>> @@ -54,26 +55,6 @@ struct omap2430_glue *_glue;
>>
>> static struct timer_list musb_idle_timer;
>>
>> -/**
>> - * omap4_usb_phy_mailbox - write to usb otg mailbox
>> - * @glue: struct omap2430_glue *
>> - * @val: the value to be written to the mailbox
>> - *
>> - * On detection of a device (ID pin is grounded), this API should be called
>> - * to set AVALID, VBUSVALID and ID pin is grounded.
>> - *
>> - * When OMAP is connected to a host (OMAP in device mode), this API
>> - * is called to set AVALID, VBUSVALID and ID pin in high impedance.
>> - *
>> - * XXX: This function will be removed once we have a seperate driver for
>> - * control module
>> - */
>> -static void omap4_usb_phy_mailbox(struct omap2430_glue *glue, u32 val)
>> -{
>> - if (glue->control_otghs)
>> - writel(val, glue->control_otghs);
>> -}
>> -
>> static void musb_do_idle(unsigned long _musb)
>> {
>> struct musb *musb = (void *)_musb;
>> @@ -269,7 +250,6 @@ EXPORT_SYMBOL_GPL(omap_musb_mailbox);
>>
>> static void omap_musb_set_mailbox(struct omap2430_glue *glue)
>> {
>> - u32 val;
>> struct musb *musb = glue_to_musb(glue);
>> struct device *dev = musb->controller;
>> struct musb_hdrc_platform_data *pdata = dev->platform_data;
>> @@ -285,8 +265,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
>> musb->xceiv->last_event = USB_EVENT_ID;
>> if (musb->gadget_driver) {
>> pm_runtime_get_sync(dev);
>> - val = AVALID | VBUSVALID;
>> - omap4_usb_phy_mailbox(glue, val);
>> + if (!IS_ERR(glue->control_otghs))
>> + omap_control_usb_host_mode(glue->control_otghs);
>
> you could introduce a helper to do the checks for you. something like:
>
> static inline void omap_control_set_mode(*ctrl, int mode)
> {
> if (IS_ERR(glue->control_otghs))
> return;
>
> switch (mode) {
> case HOST:
> omap_control_usb_host_mode(ctrl);
> break;
> case DEVICE:
> omap_control_usb_device(ctrl)
> break;
> default:
> meh();
> }
> }
>
> likewise for power() method
Ok.
Thanks
Kishon
More information about the devicetree-discuss
mailing list