[PATCH 1/2] ARM: davinci: da850: add pinctrl driver entries

Kumar, Anil anilkumar.v at ti.com
Tue Jan 8 16:26:09 EST 2013


On Mon, Jan 07, 2013 at 20:35:37, Nori, Sekhar wrote:
> Hi Anil,
> 
> On 12/7/2012 3:57 PM, Kumar, Anil wrote:
> > For DT, DaVinci platform can use pinctrl-single driver for handling
> > padconf registers.
> > 
> > Enable PINCTRL Kconfig for all DaVinci platform. Add required
> > pinctrl DT entries in da850 dts file.
> > 
> > Test procedure
> >  1)Populate DT file with NAND node information.
> >  2)Populate board DT file with pinmux information for NAND.
> >  3)Boot and confirm NAND is detected by the kernel.
> >  4)cat /proc/mtd to show partitions.
> > 
> > Signed-off-by: Kumar, Anil <anilkumar.v at ti.com>
> > ---
> > :000000 100644 0000000... f999d9e... A	Documentation/devicetree/bindings/arm/davinci/pinctrl.txt
> > :100644 100644 06e0adf... 54a5405... M	arch/arm/Kconfig
> > :100644 100644 37dc5a3... 8cac9d2... M	arch/arm/boot/dts/da850-evm.dts
> > :100644 100644 fbada87... 94471bc... M	arch/arm/boot/dts/da850.dtsi
> > :100644 100644 f292239... 0892db4... M	arch/arm/configs/da8xx_omapl_defconfig
> >  .../devicetree/bindings/arm/davinci/pinctrl.txt    |   29 ++++++++++++++++++++
> >  arch/arm/Kconfig                                   |    1 +
> >  arch/arm/boot/dts/da850-evm.dts                    |    3 ++
> >  arch/arm/boot/dts/da850.dtsi                       |   10 +++++++
> >  arch/arm/configs/da8xx_omapl_defconfig             |    1 +
> >  5 files changed, 44 insertions(+), 0 deletions(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/arm/davinci/pinctrl.txt b/Documentation/devicetree/bindings/arm/davinci/pinctrl.txt
> > new file mode 100644
> > index 0000000..f999d9e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/arm/davinci/pinctrl.txt
> > @@ -0,0 +1,29 @@
> > +* Texas Instruments Davinci pinctrl-single
> > +
> > +This file provides information, what the device node for the
> > +davinci pinctrl-single interface contain.
> > +
> > +Required properties:
> > +- compatible: "pinctrl-single";
> > +
> > +- reg : offset and length of the register set for the mux registers
> > +
> > +- pinctrl-single,bit-per-mux: mask of allowed pinmux function bits in the
> > +  pinmux register
> > +
> > +- pinctrl-single,register-width: pinmux register access width in bits
> > +
> > +- pinctrl-single,function-mask:  mask of allowed pinmux function bits in
> > +  the pinmux register
> > +
> > +Example:
> > +pmx_core:pinmux at 14120 {
> > +		compatible = "pinctrl-single";
> > +		reg = <0x14120 0x50>;
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		pinctrl-single,bit-per-mux;
> > +		pinctrl-single,register-width = <32>;
> > +		pinctrl-single,function-mask = <0xffffffff>;
> > +};
> 
> These bindings are already documented as part of
> Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt. No need to
> repeat.

Ok I will remove this documentation in next patch series.

> 
> > +~
> > diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> > index 06e0adf..54a5405 100644
> > --- a/arch/arm/Kconfig
> > +++ b/arch/arm/Kconfig
> > @@ -924,6 +924,7 @@ config ARCH_DAVINCI
> >  	select GENERIC_IRQ_CHIP
> >  	select HAVE_IDE
> >  	select NEED_MACH_GPIO_H
> > +	select PINCTRL
> 
> No need to force this across DaVinci. You can select only for MACH_DA8XX_DT.

Ok I will do for MACH_DA8XX_DT only in next patch series.

> 
> >  	select USE_OF
> >  	select ZONE_DMA
> >  	help
> > diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
> > index 37dc5a3..8cac9d2 100644
> > --- a/arch/arm/boot/dts/da850-evm.dts
> > +++ b/arch/arm/boot/dts/da850-evm.dts
> > @@ -15,6 +15,9 @@
> >  	model = "DA850/AM1808/OMAP-L138 EVM";
> >  
> >  	soc {
> > +		pmx_core:pinmux at 14120 {
> 
> 'pmx_core:pinmux at 1c14120' instead like the way uart is defined?

Sorry, I will correct this in next patch series.

> 
> > +			status = "okay";
> > +		};
> >  		serial0: serial at 1c42000 {
> >  			status = "okay";
> >  		};
> > diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
> > index fbada87..94471bc 100644
> > --- a/arch/arm/boot/dts/da850.dtsi
> > +++ b/arch/arm/boot/dts/da850.dtsi
> > @@ -29,6 +29,16 @@
> >  		#size-cells = <1>;
> >  		ranges = <0x0 0x01c00000 0x400000>;
> >  
> > +		pmx_core:pinmux at 14120 {
> > +			compatible = "pinctrl-single";
> > +			reg = <0x14120 0x50>;
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +			pinctrl-single,bit-per-mux;
> > +			pinctrl-single,register-width = <32>;
> > +			pinctrl-single,function-mask = <0xffffffff>;
> > +			status = "disabled";
> > +		};
> >  		serial0: serial at 1c42000 {
> >  			compatible = "ns16550a";
> >  			reg = <0x42000 0x100>;
> > diff --git a/arch/arm/configs/da8xx_omapl_defconfig b/arch/arm/configs/da8xx_omapl_defconfig
> > index f292239..0892db4 100644
> > --- a/arch/arm/configs/da8xx_omapl_defconfig
> > +++ b/arch/arm/configs/da8xx_omapl_defconfig
> 
> I would like the defconfig changes to be separated out into a different
> patch.

Ok, I will make separate patch for this in next patch series.

> 
> Thanks,
> Sekhar
> 



More information about the devicetree-discuss mailing list