[PATCH 3/5] arm: dts: omap4-panda: Add I2c pinctrl data

[Jon Hunter]

On 02/13/2013 09:57 AM, Jon Hunter wrote:
> 
> On 02/13/2013 03:28 AM, Sourav Poddar wrote:
>> Booting 3.8-rc6 on omap4 panda results in the following error
>>
>> [    0.444427] omap_i2c 48070000.i2c: did not get pins for i2c error: -19
>> [    0.445770] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz
>> [    0.473937] omap_i2c 48072000.i2c: did not get pins for i2c error: -19
>> [    0.474670] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz
>> [    0.474822] omap_i2c 48060000.i2c: did not get pins for i2c error: -19
>> [    0.476379] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz
>> [    0.477294] omap_i2c 48350000.i2c: did not get pins for i2c error: -19
>> [    0.477996] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz
>> [    0.483398] Switching to clocksource 32k_counter
>>
>> This happens because omap4 panda dts file is not adapted to use i2c through
>> pinctrl framework. Populating i2c pinctrl data to get rid of the error.
> 
> What about the panda-es and panda-a4?
> 
>> Tested on omap4460 panda with 3.8-rc6 kernel.
>>
>> Signed-off-by: Sourav Poddar <sourav.poddar at ti.com>
>> Reported-by: Luciano Coelho <coelho at ti.com>
>> ---
>>  arch/arm/boot/dts/omap4-panda.dts |   40 +++++++++++++++++++++++++++++++++++++
>>  1 files changed, 40 insertions(+), 0 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts
>> index 4122efe..f951e6b 100644
>> --- a/arch/arm/boot/dts/omap4-panda.dts
>> +++ b/arch/arm/boot/dts/omap4-panda.dts
>> @@ -110,9 +110,40 @@
>>  			0x58 0x10b	/* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */
>>  		>;
>>  	};
>> +
>> +	i2c1_pins: pinmux_i2c1_pins {
>> +		pinctrl-single,pins = <
>> +			0xe2 0x118        /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */
>> +			0xe4 0x118        /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */
>> +		>;
>> +	};
>> +
>> +	i2c2_pins: pinmux_i2c2_pins {
>> +		pinctrl-single,pins = <
>> +			0xe6 0x118        /* i2c2_scl PULLUP | INPUTENABLE | MODE0 */
>> +			0xe8 0x118        /* i2c2_sda PULLUP | INPUTENABLE | MODE0 */
>> +		>;
>> +	};
>> +
>> +	i2c3_pins: pinmux_i2c3_pins {
>> +		pinctrl-single,pins = <
>> +			0xea 0x118        /* i2c3_scl PULLUP | INPUTENABLE | MODE0 */
>> +			0xec 0x118     /* i2c3_sda PULLUP | INPUTENABLE | MODE0 */
>> +		>;
>> +	};
>> +
>> +	i2c4_pins: pinmux_i2c4_pins {
>> +		pinctrl-single,pins = <
>> +			0xee 0x118        /* i2c4_scl PULLUP | INPUTENABLE | MODE0 */
>> +			0xf0 0x118     /* i2c4_sda PULLUP | INPUTENABLE | MODE0 */
>> +		>;
>> +	};
>>  };
> 
> A quick look at the data manual shows that omap4430 and omap4460 has the
> same pin mux options for i2c. Furthermore, the data manual shows only
> one mux option for i2c1-4. Therefore, should these mux options be placed
> in omap4.dtsi? Boards not using specific i2c controllers can disabled
> them in there board dts file (same way we do for mmc).

I guess for i2c, a given omap4 board may use external pull-ups and not
use the internal ones and so putting this in the omap4.dtsi may not be
desirable. However, it seems that a common omap4-panda.dtsi could be
used here.

Cheers
Jon