[PATCH RFC 3/7] ARM: OMAP: gpmc-smsc911x: add DT dev node init function

Mark Rutland mark.rutland at arm.com
Mon Feb 11 21:30:51 EST 2013


Hi,

I have a few comments on the binding and the way it's parsed.

On Sat, Feb 09, 2013 at 08:44:27PM +0000, Javier Martinez Canillas wrote:
> This patch adds a helper function to parse a device node that
> contains all the properties needed to initialize an smsc911x
> device connected to an OMAP processor through OMAP's GPMC.
> 
> Signed-off-by: Javier Martinez Canillas <javier.martinez at collabora.co.uk>
> ---
>  .../devicetree/bindings/net/gpmc-smsc911x.txt      |   39 ++++++++++++++++++++
>  arch/arm/mach-omap2/gpmc-smsc911x.c                |   29 +++++++++++++++
>  arch/arm/mach-omap2/gpmc-smsc911x.h                |    6 +++
>  3 files changed, 74 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/net/gpmc-smsc911x.txt
> 
> diff --git a/Documentation/devicetree/bindings/net/gpmc-smsc911x.txt b/Documentation/devicetree/bindings/net/gpmc-smsc911x.txt
> new file mode 100644
> index 0000000..8bb0df2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/gpmc-smsc911x.txt
> @@ -0,0 +1,39 @@
> +* GPMC connected Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller
> +
> +GPMC connected SMSC LAN911x/912x Controllers are represented as child nodes
> +of the OMAP General-Purpose Memory Controller with a name of "gpmc_smsc911x".
> +
> +All timing relevant properties as well as generic gpmc child properties are
> +explained in a separate documents - please refer to
> +Documentation/devicetree/bindings/bus/ti-gpmc.txt
> +
> +Required properties:
> +- gpmc,cs : The chip select line the pheripheral is connected to
> +- gpmc,gpio_irq : The GPIO pin that is connected to the SMSC LAN IRQ line

In devicetree land, we use '-' in preference of '_' in property names.

So this should be "gpio-irq"

> +
> +Optional properties:
> +- gpmc,flags : SMSC LAN flags - please refer to include/linux/smsc911x.h

Please don't do this. It should only be necessary to read binding documents and
hardware datasheets to write a dts. Referring to Linux internals creates a
flaky ABI that's only going to break when things get renamed/moved/modified.

The flags variable used internally by the driver don't have to have a 1-1
correspondence with a single property in the binding. You can have boolean
properties (named, but without a value) in the dt specifying each flag
individually. That way the dts is easier to read, is less tied to linux
internals (and every property is *fully* documented), and it's far easier to
add new flags in future if necessary.

> +- gpmc,gpio_reset : The GPIO pin connected to the SMSC LAN reset line

Preferably: "gpio-reset".

> +
> +Note: Besides these properties, the gpmc_smsc911x device node could need
> +aditional setup such as pin/pad mux settings and voltage regulators. This
> +depend on how the pheripheral is wired and his board specific.
> +
> +Example (for an OMAP3 board):
> +
> +gpmc at 6e000000 {
> +	      compatible = "ti,omap3430-gpmc";
> +	      ti,hwmods = "gpmc";
> +	      reg = <0x6e000000 0x1000000>;
> +	      interrupts = <20>;
> +	      gpmc,num-cs = <8>;
> +	      gpmc,num-waitpins = <4>;
> +	      #address-cells = <2>;
> +	      #size-cells = <1>;
> +
> +	      gpmc_smsc911x at 0 {
> +			      gpmc,cs = <5>;
> +			      gpmc,gpio_irq = <176>;
> +			      gpmc,flags = <4>; /* SMSC911X_USE_32BIT */

Here you could have a boolean property "gpmc,use-32bit" (or possibly
"gpmc,use-bits", which can either be 32 or 16).

> +	      };
> +};
> diff --git a/arch/arm/mach-omap2/gpmc-smsc911x.c b/arch/arm/mach-omap2/gpmc-smsc911x.c
> index 5ce00ad2..59a2ee4 100644
> --- a/arch/arm/mach-omap2/gpmc-smsc911x.c
> +++ b/arch/arm/mach-omap2/gpmc-smsc911x.c
> @@ -19,6 +19,7 @@
>  #include <linux/interrupt.h>
>  #include <linux/io.h>
>  #include <linux/smsc911x.h>
> +#include <linux/of.h>
>  
>  #include "gpmc.h"
>  #include "gpmc-smsc911x.h"
> @@ -98,3 +99,31 @@ free1:
>  
>  	pr_err("Could not initialize smsc911x device\n");
>  }
> +
> +int gpmc_smsc911x_init_dt(struct device_node *node)
> +{
> +	struct omap_smsc911x_platform_data gpmc_cfg;
> +
> +	if (WARN_ON(!node))
> +		return -ENODEV;
> +
> +	if (of_property_read_u32(node, "gpmc,cs", &gpmc_cfg.cs)) {
> +		pr_err("Unable to get GPMC smsc911x chip select\n");
> +		return -EINVAL;
> +	}
> +
> +	if (of_property_read_u32(node, "gpmc,gpio_irq", &gpmc_cfg.gpio_irq)) {
> +		pr_err("Unable to get GPMC smsc911x GPIO IRQ\n");
> +		return -EINVAL;
> +	}
> +
> +	if (of_property_read_u32(node, "gpmc,gpio_reset", &gpmc_cfg.gpio_reset))
> +		gpmc_cfg.gpio_reset = -EINVAL;
> +
> +	if (of_property_read_u32(node, "gpmc,flags", &gpmc_cfg.flags))
> +		gpmc_cfg.flags = 0;

Is no sanity checking required for any of the above properties?

To handle separate flags here, you can use something like:

if (of_property_read_bool(node, "gpmc,use-32bit")
	flags |= SMSC911X_USE_32BIT;

[...]

Thanks,
Mark.



More information about the devicetree-discuss mailing list