[PATCH] arm: mvebu: Add SPI flash on Armada XP-GP board

Gregory CLEMENT gregory.clement at free-electrons.com
Wed Feb 6 23:31:23 EST 2013


On 02/06/2013 11:54 AM, Ezequiel Garcia wrote:
> Hi Gregory,
> 
> On Tue, Feb 05, 2013 at 09:17:02PM +0100, Gregory CLEMENT wrote:
>> On 02/05/2013 05:28 PM, Gregory CLEMENT wrote:
>>> Hi Ezequiel,
>>>
>>> On 02/05/2013 12:24 PM, Ezequiel Garcia wrote:
>>>> This patch adds an SPI master device node for Armada XP-GP board.
>>>> This master node is an SPI flash controller 'n25q128a13'.
>>>>
>>>> Since there is no 'partitions' node declared, one full sized
>>>> partition named as the device will be created.
>>>>
>>>> Cc: Gregory Clement <gregory.clement at free-electrons.com>
>>>> Cc: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
>>>> Cc: Lior Amsalem <alior at marvell.com>
>>>> Signed-off-by: Ezequiel Garcia <ezequiel.garcia at free-electrons.com>
>>>> ---
>>>> This patch depends on:
>>>>
>>>>  1. Gregory's patch for Armada XP GP board:
>>>>       arm: mvebu: support for the new Armada XP development board(DB-MV784MP-GP)
>>>>
>>>>  2. My previous patch for SPI on Armada 370/XP:
>>>>       arm: mvebu: Add support for SPI controller in Armada 370/XP
>>>>
>>>> And don't forget to compile the SPI flash driver, CONFIG_MTD_M25P80=y
>>>>
>>>>  arch/arm/boot/dts/armada-xp-gp.dts |   12 ++++++++++++
>>>>  1 files changed, 12 insertions(+), 0 deletions(-)
>>>>
>>>> diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts
>>>> index 3eea531..1c8afe2 100644
>>>> --- a/arch/arm/boot/dts/armada-xp-gp.dts
>>>> +++ b/arch/arm/boot/dts/armada-xp-gp.dts
>>>> @@ -97,5 +97,17 @@
>>>>  			phy = <&phy3>;
>>>>  			phy-mode = "rgmii-id";
>>>>  		};
>>>> +
>>>> +		spi0: spi at d0010600 {
>>>> +			status = "okay";
>>>> +
>>>> +			spi-flash at 0 {
>>>> +				#address-cells = <1>;
>>>> +				#size-cells = <1>;
>>>> +				compatible = "n25q128a13";
>>>> +				reg = <0>; /* Chip select 0 */
>>>> +				spi-max-frequency = <108000000>;
>>
>> I had a remark about it, according to the datasheet, 108MHz is the
>> maximum frequency for the all the instructions but the READ
>> instruction. For the READ the maximum frequency is 54MHz. So I wonder
>> if we shouldn't use 54000000 here.
>>
> 
> Mmm... nice catch.
> 
> The mtd driver for the spi flash (m25p80) will use FAST_READ opcode
> if CONFIG_M25PXX_USE_FAST_READ is selected, and this option
> is selected by default.

OK I didn't notice that thre wre a FAST_READ which was supported by
Linux. So I think we can keep 108000000 as spi-max-frequency.

> However we cannot count on this option being selected, of course.
> 
> On the other side, after some testing with spi-max-frequency = 50 MHz
> and also with spi-max-frequency = 108 MHz I'm seeing the flash often
> (not always) stalls when trying to read the full device through dd:
> 
> / # dd if=/dev/mtd0ro of=/dev/null
> 
> This happens regardless of CONFIG_M25PXX_USE_FAST_READ, and regardless
> of spi-max-frequency = 50 MHz or 54 MHz or 108 MHz.
> 
> Note that setting 108 MHz is useless in our case, because there's
> an upper limit of 62.5 MHz set by the core clock of the SoC.
> 
> Using a read block size of 1M, the read completes OK -- always:
> 
> / # dd if=/dev/mtd0 of=/dev/null bs=1M
> 16+0 records in
> 16+0 records out
> 16777216 bytes (16.0MB) copied, 27.306048 seconds, 600.0KB/s
> 
> Moreover, when the read completes, the achieved bandwidth
> is the same for 40, 50, 54, or 108 MHz.
> 
> If we set spi-max-frequency to 27 MHz (108 MHz / 4), it looks like the stalling
> disappear and the read always completes OK, at almost half the speed:
> 
> / # dd if=/dev/mtd0ro of=/dev/null
> 32768+0 records in
> 32768+0 records out
> 16777216 bytes (16.0MB) copied, 49.005122 seconds, 334.3KB/s
> 
> So according to this analysis, we whould set 27 MHz as the max
> frequency, based on nothing but in these tests.
> 
> I'm not sure the stalling is due to the clocking or due to
> some driver bug (I don't like the tricks pulled by the busy loop
> in orion_spi_wait_till_ready() but probably this is completely unrelated).
> 
> Adding some SPI people in Cc, hoping they can shed a light on this.
> 
> What do you think?

We have just seen this on IRC, so it seemed it was actually a problem in
userspace not in kernel space.

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com


More information about the devicetree-discuss mailing list