[PATCH v4 4/5] ARM: dts: mvebu: introduce internal-regs node
Gregory CLEMENT
gregory.clement at free-electrons.com
Sat Apr 13 00:29:09 EST 2013
Introduce a 'internal-regs' subnode, under which all devices are
moved. This is not really needed for now, but will be for the
mvebu-mbus driver. This generates a lot of code movement since it's
indenting by one more tab all the devices. So it was a good
opportunity to fix all the bad indentation.
Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
---
arch/arm/boot/dts/armada-370-db.dts | 134 +++----
arch/arm/boot/dts/armada-370-mirabox.dts | 176 ++++-----
arch/arm/boot/dts/armada-370-rd.dts | 96 ++---
arch/arm/boot/dts/armada-370-xp.dtsi | 301 +++++++--------
arch/arm/boot/dts/armada-370.dtsi | 328 ++++++++---------
arch/arm/boot/dts/armada-xp-db.dts | 200 +++++-----
arch/arm/boot/dts/armada-xp-gp.dts | 208 +++++------
arch/arm/boot/dts/armada-xp-mv78230.dtsi | 252 ++++++-------
arch/arm/boot/dts/armada-xp-mv78260.dtsi | 308 ++++++++--------
arch/arm/boot/dts/armada-xp-mv78460.dtsi | 428 +++++++++++-----------
arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts | 260 ++++++-------
arch/arm/boot/dts/armada-xp.dtsi | 193 +++++-----
12 files changed, 1452 insertions(+), 1432 deletions(-)
diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts
index e766f8b..2353b1f 100644
--- a/arch/arm/boot/dts/armada-370-db.dts
+++ b/arch/arm/boot/dts/armada-370-db.dts
@@ -30,85 +30,87 @@
};
soc {
- serial at 12000 {
- clock-frequency = <200000000>;
- status = "okay";
- };
- sata at a0000 {
- nr-ports = <2>;
- status = "okay";
- };
-
- mdio {
- phy0: ethernet-phy at 0 {
- reg = <0>;
+ internal-regs {
+ serial at 12000 {
+ clock-frequency = <200000000>;
+ status = "okay";
};
-
- phy1: ethernet-phy at 1 {
- reg = <1>;
+ sata at a0000 {
+ nr-ports = <2>;
+ status = "okay";
};
- };
- ethernet at 70000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "rgmii-id";
- };
- ethernet at 74000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "rgmii-id";
- };
+ mdio {
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
- mvsdio at d4000 {
- pinctrl-0 = <&sdio_pins1>;
- pinctrl-names = "default";
- /*
- * This device is disabled by default, because
- * using the SD card connector requires
- * changing the default CON40 connector
- * "DB-88F6710_MPP_2xRGMII_DEVICE_Jumper" to a
- * different connector
- * "DB-88F6710_MPP_RGMII_SD_Jumper".
- */
- status = "disabled";
- /* No CD or WP GPIOs */
- };
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+ };
- usb at 50000 {
- status = "okay";
- };
+ ethernet at 70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet at 74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
- usb at 51000 {
- status = "okay";
- };
+ mvsdio at d4000 {
+ pinctrl-0 = <&sdio_pins1>;
+ pinctrl-names = "default";
+ /*
+ * This device is disabled by default, because
+ * using the SD card connector requires
+ * changing the default CON40 connector
+ * "DB-88F6710_MPP_2xRGMII_DEVICE_Jumper" to a
+ * different connector
+ * "DB-88F6710_MPP_RGMII_SD_Jumper".
+ */
+ status = "disabled";
+ /* No CD or WP GPIOs */
+ };
- spi0: spi at 10600 {
- status = "okay";
+ usb at 50000 {
+ status = "okay";
+ };
- spi-flash at 0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "mx25l25635e";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <50000000>;
+ usb at 51000 {
+ status = "okay";
};
- };
- pcie-controller {
- status = "okay";
- /*
- * The two PCIe units are accessible through
- * both standard PCIe slots and mini-PCIe
- * slots on the board.
- */
- pcie at 1,0 {
- /* Port 0, Lane 0 */
+ spi0: spi at 10600 {
status = "okay";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mx25l25635e";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+ };
};
- pcie at 2,0 {
- /* Port 1, Lane 0 */
+
+ pcie-controller {
status = "okay";
+ /*
+ * The two PCIe units are accessible through
+ * both standard PCIe slots and mini-PCIe
+ * slots on the board.
+ */
+ pcie at 1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ pcie at 2,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
};
};
};
diff --git a/arch/arm/boot/dts/armada-370-mirabox.dts b/arch/arm/boot/dts/armada-370-mirabox.dts
index 6530ae3..14e36e1 100644
--- a/arch/arm/boot/dts/armada-370-mirabox.dts
+++ b/arch/arm/boot/dts/armada-370-mirabox.dts
@@ -25,113 +25,115 @@
};
soc {
- serial at 12000 {
- clock-frequency = <200000000>;
- status = "okay";
- };
- timer at 20300 {
- clock-frequency = <600000000>;
- status = "okay";
- };
-
- pinctrl {
- pwr_led_pin: pwr-led-pin {
- marvell,pins = "mpp63";
- marvell,function = "gpo";
+ internal-regs {
+ serial at 12000 {
+ clock-frequency = <200000000>;
+ status = "okay";
};
-
- stat_led_pins: stat-led-pins {
- marvell,pins = "mpp64", "mpp65";
- marvell,function = "gpio";
+ timer at 20300 {
+ clock-frequency = <600000000>;
+ status = "okay";
};
- };
- gpio_leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pwr_led_pin &stat_led_pins>;
+ pinctrl {
+ pwr_led_pin: pwr-led-pin {
+ marvell,pins = "mpp63";
+ marvell,function = "gpo";
+ };
- green_pwr_led {
- label = "mirabox:green:pwr";
- gpios = <&gpio1 31 1>;
- linux,default-trigger = "heartbeat";
+ stat_led_pins: stat-led-pins {
+ marvell,pins = "mpp64", "mpp65";
+ marvell,function = "gpio";
+ };
};
- blue_stat_led {
- label = "mirabox:blue:stat";
- gpios = <&gpio2 0 1>;
- linux,default-trigger = "cpu0";
+ gpio_leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_led_pin &stat_led_pins>;
+
+ green_pwr_led {
+ label = "mirabox:green:pwr";
+ gpios = <&gpio1 31 1>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ blue_stat_led {
+ label = "mirabox:blue:stat";
+ gpios = <&gpio2 0 1>;
+ linux,default-trigger = "cpu0";
+ };
+
+ green_stat_led {
+ label = "mirabox:green:stat";
+ gpios = <&gpio2 1 1>;
+ default-state = "off";
+ };
};
- green_stat_led {
- label = "mirabox:green:stat";
- gpios = <&gpio2 1 1>;
- default-state = "off";
- };
- };
+ mdio {
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
- mdio {
- phy0: ethernet-phy at 0 {
- reg = <0>;
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
};
-
- phy1: ethernet-phy at 1 {
- reg = <1>;
+ ethernet at 70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet at 74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
};
- };
- ethernet at 70000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "rgmii-id";
- };
- ethernet at 74000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "rgmii-id";
- };
-
- mvsdio at d4000 {
- pinctrl-0 = <&sdio_pins3>;
- pinctrl-names = "default";
- status = "okay";
- /*
- * No CD or WP GPIOs: SDIO interface used for
- * Wifi/Bluetooth chip
- */
- };
-
- usb at 50000 {
- status = "okay";
- };
- usb at 51000 {
- status = "okay";
- };
+ mvsdio at d4000 {
+ pinctrl-0 = <&sdio_pins3>;
+ pinctrl-names = "default";
+ status = "okay";
+ /*
+ * No CD or WP GPIOs: SDIO interface used for
+ * Wifi/Bluetooth chip
+ */
+ };
- i2c at 11000 {
- status = "okay";
- clock-frequency = <100000>;
- pca9505: pca9505 at 25 {
- compatible = "nxp,pca9505";
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x25>;
+ usb at 50000 {
+ status = "okay";
};
- };
- pcie-controller {
- status = "okay";
+ usb at 51000 {
+ status = "okay";
+ };
- /* Internal mini-PCIe connector */
- pcie at 1,0 {
- /* Port 0, Lane 0 */
+ i2c at 11000 {
status = "okay";
+ clock-frequency = <100000>;
+ pca9505: pca9505 at 25 {
+ compatible = "nxp,pca9505";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x25>;
+ };
};
- /* Connected on the PCB to a USB 3.0 XHCI controller */
- pcie at 2,0 {
- /* Port 1, Lane 0 */
+ pcie-controller {
status = "okay";
+
+ /* Internal mini-PCIe connector */
+ pcie at 1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ /* Connected on the PCB to a USB 3.0 XHCI controller */
+ pcie at 2,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
};
};
};
diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/armada-370-rd.dts
index 83d5c04..130f839 100644
--- a/arch/arm/boot/dts/armada-370-rd.dts
+++ b/arch/arm/boot/dts/armada-370-rd.dts
@@ -28,60 +28,62 @@
};
soc {
- serial at 12000 {
- clock-frequency = <200000000>;
- status = "okay";
- };
- sata at a0000 {
- nr-ports = <2>;
- status = "okay";
- };
-
- mdio {
- phy0: ethernet-phy at 0 {
- reg = <0>;
+ internal-regs {
+ serial at 12000 {
+ clock-frequency = <200000000>;
+ status = "okay";
};
+ sata at a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+
+ mdio {
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
- phy1: ethernet-phy at 1 {
- reg = <1>;
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
};
- };
- ethernet at 70000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "sgmii";
- };
- ethernet at 74000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "rgmii-id";
- };
+ ethernet at 70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "sgmii";
+ };
+ ethernet at 74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
- mvsdio at d4000 {
- pinctrl-0 = <&sdio_pins1>;
- pinctrl-names = "default";
- status = "okay";
- /* No CD or WP GPIOs */
- };
+ mvsdio at d4000 {
+ pinctrl-0 = <&sdio_pins1>;
+ pinctrl-names = "default";
+ status = "okay";
+ /* No CD or WP GPIOs */
+ };
- usb at 50000 {
- status = "okay";
- };
+ usb at 50000 {
+ status = "okay";
+ };
- usb at 51000 {
- status = "okay";
- };
- };
+ usb at 51000 {
+ status = "okay";
+ };
- gpio-keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- button at 1 {
- label = "Software Button";
- linux,code = <116>;
- gpios = <&gpio0 6 1>;
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ button at 1 {
+ label = "Software Button";
+ linux,code = <116>;
+ gpios = <&gpio0 6 1>;
+ };
+ };
};
};
-};
+ };
diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi
index da40ce5..bf8f911 100644
--- a/arch/arm/boot/dts/armada-370-xp.dtsi
+++ b/arch/arm/boot/dts/armada-370-xp.dtsi
@@ -28,7 +28,6 @@
};
};
-
soc {
#address-cells = <1>;
#size-cells = <1>;
@@ -36,192 +35,196 @@
interrupt-parent = <&mpic>;
ranges = <0 0xd0000000 0x100000>;
- mpic: interrupt-controller at 20000 {
+ internal-regs {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mpic: interrupt-controller at 20000 {
compatible = "marvell,mpic";
#interrupt-cells = <1>;
#size-cells = <1>;
interrupt-controller;
- };
+ };
- coherency-fabric at 20200 {
+ coherency-fabric at 20200 {
compatible = "marvell,coherency-fabric";
- reg = <0x20200 0xb0>,
- <0x21810 0x1c>;
- };
+ reg = <0x20200 0xb0>, <0x21810 0x1c>;
+ };
- serial at 12000 {
+ serial at 12000 {
compatible = "snps,dw-apb-uart";
reg = <0x12000 0x100>;
reg-shift = <2>;
interrupts = <41>;
reg-io-width = <1>;
status = "disabled";
- };
- serial at 12100 {
+ };
+ serial at 12100 {
compatible = "snps,dw-apb-uart";
reg = <0x12100 0x100>;
reg-shift = <2>;
interrupts = <42>;
reg-io-width = <1>;
status = "disabled";
- };
-
- timer at 20300 {
- compatible = "marvell,armada-370-xp-timer";
- reg = <0x20300 0x30>,
- <0x21040 0x30>;
- interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
- clocks = <&coreclk 2>;
- };
-
- sata at a0000 {
- compatible = "marvell,orion-sata";
- reg = <0xa0000 0x2400>;
- interrupts = <55>;
- clocks = <&gateclk 15>, <&gateclk 30>;
- clock-names = "0", "1";
- status = "disabled";
- };
+ };
+
+ timer at 20300 {
+ compatible = "marvell,armada-370-xp-timer";
+ reg = <0x20300 0x30>, <0x21040 0x30>;
+ interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
+ clocks = <&coreclk 2>;
+ };
+
+ sata at a0000 {
+ compatible = "marvell,orion-sata";
+ reg = <0xa0000 0x2400>;
+ interrupts = <55>;
+ clocks = <&gateclk 15>, <&gateclk 30>;
+ clock-names = "0", "1";
+ status = "disabled";
+ };
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "marvell,orion-mdio";
- reg = <0x72004 0x4>;
- };
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,orion-mdio";
+ reg = <0x72004 0x4>;
+ };
- ethernet at 70000 {
+ ethernet at 70000 {
compatible = "marvell,armada-370-neta";
reg = <0x70000 0x2500>;
interrupts = <8>;
clocks = <&gateclk 4>;
status = "disabled";
- };
+ };
- ethernet at 74000 {
+ ethernet at 74000 {
compatible = "marvell,armada-370-neta";
reg = <0x74000 0x2500>;
interrupts = <10>;
clocks = <&gateclk 3>;
status = "disabled";
- };
-
- i2c0: i2c at 11000 {
- compatible = "marvell,mv64xxx-i2c";
- reg = <0x11000 0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <31>;
- timeout-ms = <1000>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
- i2c1: i2c at 11100 {
- compatible = "marvell,mv64xxx-i2c";
- reg = <0x11100 0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <32>;
- timeout-ms = <1000>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
- rtc at 10300 {
- compatible = "marvell,orion-rtc";
- reg = <0x10300 0x20>;
- interrupts = <50>;
- };
-
- mvsdio at d4000 {
- compatible = "marvell,orion-sdio";
- reg = <0xd4000 0x200>;
- interrupts = <54>;
- clocks = <&gateclk 17>;
- status = "disabled";
- };
-
- usb at 50000 {
- compatible = "marvell,orion-ehci";
- reg = <0x50000 0x500>;
- interrupts = <45>;
- status = "disabled";
- };
-
- usb at 51000 {
- compatible = "marvell,orion-ehci";
- reg = <0x51000 0x500>;
- interrupts = <46>;
- status = "disabled";
- };
+ };
+
+ i2c0: i2c at 11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <31>;
+ timeout-ms = <1000>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c at 11100 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11100 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <32>;
+ timeout-ms = <1000>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ rtc at 10300 {
+ compatible = "marvell,orion-rtc";
+ reg = <0x10300 0x20>;
+ interrupts = <50>;
+ };
+
+ mvsdio at d4000 {
+ compatible = "marvell,orion-sdio";
+ reg = <0xd4000 0x200>;
+ interrupts = <54>;
+ clocks = <&gateclk 17>;
+ status = "disabled";
+ };
- spi0: spi at 10600 {
- compatible = "marvell,orion-spi";
- reg = <0x10600 0x28>;
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- interrupts = <30>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
+ usb at 50000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x50000 0x500>;
+ interrupts = <45>;
+ status = "disabled";
+ };
- spi1: spi at 10680 {
- compatible = "marvell,orion-spi";
- reg = <0x10680 0x28>;
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- interrupts = <92>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
+ usb at 51000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x51000 0x500>;
+ interrupts = <46>;
+ status = "disabled";
+ };
+
+ spi0: spi at 10600 {
+ compatible = "marvell,orion-spi";
+ reg = <0x10600 0x28>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ interrupts = <30>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ spi1: spi at 10680 {
+ compatible = "marvell,orion-spi";
+ reg = <0x10680 0x28>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ interrupts = <92>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
- devbus-bootcs at 10400 {
- compatible = "marvell,mvebu-devbus";
- reg = <0x10400 0x8>;
- #address-cells = <1>;
- #size-cells = <1>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
+ devbus-bootcs at 10400 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <0x10400 0x8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
- devbus-cs0 at 10408 {
- compatible = "marvell,mvebu-devbus";
- reg = <0x10408 0x8>;
- #address-cells = <1>;
- #size-cells = <1>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
+ devbus-cs0 at 10408 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <0x10408 0x8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
- devbus-cs1 at 10410 {
- compatible = "marvell,mvebu-devbus";
- reg = <0x10410 0x8>;
- #address-cells = <1>;
- #size-cells = <1>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
+ devbus-cs1 at 10410 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <0x10410 0x8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
- devbus-cs2 at 10418 {
- compatible = "marvell,mvebu-devbus";
- reg = <0x10418 0x8>;
- #address-cells = <1>;
- #size-cells = <1>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
+ devbus-cs2 at 10418 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <0x10418 0x8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
- devbus-cs3 at 10420 {
- compatible = "marvell,mvebu-devbus";
- reg = <0x10420 0x8>;
- #address-cells = <1>;
- #size-cells = <1>;
- clocks = <&coreclk 0>;
- status = "disabled";
+ devbus-cs3 at 10420 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <0x10420 0x8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
};
};
-};
-
+ };
diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi
index 5c4fa65..6ef95dd 100644
--- a/arch/arm/boot/dts/armada-370.dtsi
+++ b/arch/arm/boot/dts/armada-370.dtsi
@@ -28,195 +28,195 @@
};
soc {
-
- mpic: interrupt-controller at 20000 {
- reg = <0x20a00 0x1d0>,
- <0x21870 0x58>;
- };
-
- system-controller at 18200 {
+ internal-regs {
+ system-controller at 18200 {
compatible = "marvell,armada-370-xp-system-controller";
reg = <0x18200 0x100>;
- };
-
- L2: l2-cache {
- compatible = "marvell,aurora-outer-cache";
- reg = <0xd0008000 0x1000>;
- cache-id-part = <0x100>;
- wt-override;
- };
-
- pinctrl {
- compatible = "marvell,mv88f6710-pinctrl";
- reg = <0x18000 0x38>;
-
- sdio_pins1: sdio-pins1 {
- marvell,pins = "mpp9", "mpp11", "mpp12",
- "mpp13", "mpp14", "mpp15";
- marvell,function = "sd0";
};
- sdio_pins2: sdio-pins2 {
- marvell,pins = "mpp47", "mpp48", "mpp49",
- "mpp50", "mpp51", "mpp52";
- marvell,function = "sd0";
+ L2: l2-cache {
+ compatible = "marvell,aurora-outer-cache";
+ reg = <0xd0008000 0x1000>;
+ cache-id-part = <0x100>;
+ wt-override;
};
- sdio_pins3: sdio-pins3 {
- marvell,pins = "mpp48", "mpp49", "mpp50",
- "mpp51", "mpp52", "mpp53";
- marvell,function = "sd0";
+ mpic: interrupt-controller at 20000 {
+ reg = <0x20a00 0x1d0>, <0x21870 0x58>;
};
- };
-
- gpio0: gpio at 18100 {
- compatible = "marvell,orion-gpio";
- reg = <0x18100 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <82>, <83>, <84>, <85>;
- };
-
- gpio1: gpio at 18140 {
- compatible = "marvell,orion-gpio";
- reg = <0x18140 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <87>, <88>, <89>, <90>;
- };
- gpio2: gpio at 18180 {
- compatible = "marvell,orion-gpio";
- reg = <0x18180 0x40>;
- ngpios = <2>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <91>;
- };
-
- coreclk: mvebu-sar at 18230 {
- compatible = "marvell,armada-370-core-clock";
- reg = <0x18230 0x08>;
- #clock-cells = <1>;
- };
-
- gateclk: clock-gating-control at 18220 {
- compatible = "marvell,armada-370-gating-clock";
- reg = <0x18220 0x4>;
- clocks = <&coreclk 0>;
- #clock-cells = <1>;
- };
-
- xor at 60800 {
- compatible = "marvell,orion-xor";
- reg = <0x60800 0x100
- 0x60A00 0x100>;
- status = "okay";
-
- xor00 {
- interrupts = <51>;
- dmacap,memcpy;
- dmacap,xor;
- };
- xor01 {
- interrupts = <52>;
- dmacap,memcpy;
- dmacap,xor;
- dmacap,memset;
+ pinctrl {
+ compatible = "marvell,mv88f6710-pinctrl";
+ reg = <0x18000 0x38>;
+
+ sdio_pins1: sdio-pins1 {
+ marvell,pins = "mpp9", "mpp11", "mpp12",
+ "mpp13", "mpp14", "mpp15";
+ marvell,function = "sd0";
+ };
+
+ sdio_pins2: sdio-pins2 {
+ marvell,pins = "mpp47", "mpp48", "mpp49",
+ "mpp50", "mpp51", "mpp52";
+ marvell,function = "sd0";
+ };
+
+ sdio_pins3: sdio-pins3 {
+ marvell,pins = "mpp48", "mpp49", "mpp50",
+ "mpp51", "mpp52", "mpp53";
+ marvell,function = "sd0";
+ };
};
- };
- xor at 60900 {
- compatible = "marvell,orion-xor";
- reg = <0x60900 0x100
- 0x60b00 0x100>;
- status = "okay";
-
- xor10 {
- interrupts = <94>;
- dmacap,memcpy;
- dmacap,xor;
- };
- xor11 {
- interrupts = <95>;
- dmacap,memcpy;
- dmacap,xor;
- dmacap,memset;
+ gpio0: gpio at 18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <82>, <83>, <84>, <85>;
};
- };
-
- usb at 50000 {
- clocks = <&coreclk 0>;
- };
- usb at 51000 {
- clocks = <&coreclk 0>;
- };
+ gpio1: gpio at 18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <87>, <88>, <89>, <90>;
+ };
- thermal at 18300 {
- compatible = "marvell,armada370-thermal";
- reg = <0x18300 0x4
- 0x18304 0x4>;
- status = "okay";
- };
+ gpio2: gpio at 18180 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18180 0x40>;
+ ngpios = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <91>;
+ };
- pcie-controller {
- compatible = "marvell,armada-370-pcie";
- status = "disabled";
- device_type = "pci";
+ coreclk: mvebu-sar at 18230 {
+ compatible = "marvell,armada-370-core-clock";
+ reg = <0x18230 0x08>;
+ #clock-cells = <1>;
+ };
- #address-cells = <3>;
- #size-cells = <2>;
+ gateclk: clock-gating-control at 18220 {
+ compatible = "marvell,armada-370-gating-clock";
+ reg = <0x18220 0x4>;
+ clocks = <&coreclk 0>;
+ #clock-cells = <1>;
+ };
- bus-range = <0x00 0xff>;
+ xor at 60800 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60800 0x100
+ 0x60A00 0x100>;
+ status = "okay";
+
+ xor00 {
+ interrupts = <51>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor01 {
+ interrupts = <52>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
- reg = <0x40000 0x2000>, <0x80000 0x2000>;
+ xor at 60900 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60900 0x100
+ 0x60b00 0x100>;
+ status = "okay";
+
+ xor10 {
+ interrupts = <94>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor11 {
+ interrupts = <95>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
- reg-names = "pcie0.0", "pcie1.0";
+ usb at 50000 {
+ clocks = <&coreclk 0>;
+ };
- ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */
- 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
- 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
+ usb at 51000 {
+ clocks = <&coreclk 0>;
+ };
- pcie at 1,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
- reg = <0x0800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 58>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 5>;
- status = "disabled";
+ thermal at 18300 {
+ compatible = "marvell,armada370-thermal";
+ reg = <0x18300 0x4
+ 0x18304 0x4>;
+ status = "okay";
};
- pcie at 2,0 {
+ pcie-controller {
+ compatible = "marvell,armada-370-pcie";
+ status = "disabled";
device_type = "pci";
- assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
- reg = <0x1000 0 0 0 0>;
+
#address-cells = <3>;
#size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 62>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 9>;
- status = "disabled";
+
+ bus-range = <0x00 0xff>;
+
+ reg = <0x40000 0x2000>, <0x80000 0x2000>;
+
+ reg-names = "pcie0.0", "pcie1.0";
+
+ ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */
+ 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
+ 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+ pcie at 1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+
+ pcie at 2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 62>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 9>;
+ status = "disabled";
+ };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts
index e37863f..6c8b032 100644
--- a/arch/arm/boot/dts/armada-xp-db.dts
+++ b/arch/arm/boot/dts/armada-xp-db.dts
@@ -30,128 +30,130 @@
};
soc {
- serial at 12000 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial at 12100 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial at 12200 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial at 12300 {
- clock-frequency = <250000000>;
- status = "okay";
- };
-
- sata at a0000 {
- nr-ports = <2>;
- status = "okay";
- };
-
- mdio {
- phy0: ethernet-phy at 0 {
- reg = <0>;
+ internal-regs {
+ serial at 12000 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- phy1: ethernet-phy at 1 {
- reg = <1>;
+ serial at 12100 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- phy2: ethernet-phy at 2 {
- reg = <25>;
+ serial at 12200 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- phy3: ethernet-phy at 3 {
- reg = <27>;
+ serial at 12300 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
- };
-
- ethernet at 70000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "rgmii-id";
- };
- ethernet at 74000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "rgmii-id";
- };
- ethernet at 30000 {
- status = "okay";
- phy = <&phy2>;
- phy-mode = "sgmii";
- };
- ethernet at 34000 {
- status = "okay";
- phy = <&phy3>;
- phy-mode = "sgmii";
- };
-
- mvsdio at d4000 {
- pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
- status = "okay";
- /* No CD or WP GPIOs */
- };
- usb at 50000 {
- status = "okay";
- };
+ sata at a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
- usb at 51000 {
- status = "okay";
- };
+ mdio {
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
- usb at 52000 {
- status = "okay";
- };
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
- spi0: spi at 10600 {
- status = "okay";
+ phy2: ethernet-phy at 2 {
+ reg = <25>;
+ };
- spi-flash at 0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "m25p64";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <20000000>;
+ phy3: ethernet-phy at 3 {
+ reg = <27>;
+ };
};
- };
- pcie-controller {
- status = "okay";
+ ethernet at 70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet at 74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet at 30000 {
+ status = "okay";
+ phy = <&phy2>;
+ phy-mode = "sgmii";
+ };
+ ethernet at 34000 {
+ status = "okay";
+ phy = <&phy3>;
+ phy-mode = "sgmii";
+ };
- /*
- * All 6 slots are physically present as
- * standard PCIe slots on the board.
- */
- pcie at 1,0 {
- /* Port 0, Lane 0 */
+ mvsdio at d4000 {
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-names = "default";
status = "okay";
+ /* No CD or WP GPIOs */
};
- pcie at 2,0 {
- /* Port 0, Lane 1 */
+
+ usb at 50000 {
status = "okay";
};
- pcie at 3,0 {
- /* Port 0, Lane 2 */
+
+ usb at 51000 {
status = "okay";
};
- pcie at 4,0 {
- /* Port 0, Lane 3 */
+
+ usb at 52000 {
status = "okay";
};
- pcie at 9,0 {
- /* Port 2, Lane 0 */
+
+ spi0: spi at 10600 {
status = "okay";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+ };
};
- pcie at 10,0 {
- /* Port 3, Lane 0 */
+
+ pcie-controller {
status = "okay";
+
+ /*
+ * All 6 slots are physically present as
+ * standard PCIe slots on the board.
+ */
+ pcie at 1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ pcie at 2,0 {
+ /* Port 0, Lane 1 */
+ status = "okay";
+ };
+ pcie at 3,0 {
+ /* Port 0, Lane 2 */
+ status = "okay";
+ };
+ pcie at 4,0 {
+ /* Port 0, Lane 3 */
+ status = "okay";
+ };
+ pcie at 9,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ pcie at 10,0 {
+ /* Port 3, Lane 0 */
+ status = "okay";
+ };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts
index 55bcbff..d9972c9 100644
--- a/arch/arm/boot/dts/armada-xp-gp.dts
+++ b/arch/arm/boot/dts/armada-xp-gp.dts
@@ -37,126 +37,128 @@
};
soc {
- serial at 12000 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial at 12100 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial at 12200 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial at 12300 {
- clock-frequency = <250000000>;
- status = "okay";
- };
-
- sata at a0000 {
- nr-ports = <2>;
- status = "okay";
- };
-
- mdio {
- phy0: ethernet-phy at 0 {
- reg = <16>;
+ internal-regs {
+ serial at 12000 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- phy1: ethernet-phy at 1 {
- reg = <17>;
+ serial at 12100 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- phy2: ethernet-phy at 2 {
- reg = <18>;
+ serial at 12200 {
+ clock-frequency = <250000000>;
+ status = "okay";
+ };
+ serial at 12300 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
- phy3: ethernet-phy at 3 {
- reg = <19>;
+ sata at a0000 {
+ nr-ports = <2>;
+ status = "okay";
};
- };
- ethernet at 70000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "rgmii-id";
- };
- ethernet at 74000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "rgmii-id";
- };
- ethernet at 30000 {
- status = "okay";
- phy = <&phy2>;
- phy-mode = "rgmii-id";
- };
- ethernet at 34000 {
- status = "okay";
- phy = <&phy3>;
- phy-mode = "rgmii-id";
- };
+ mdio {
+ phy0: ethernet-phy at 0 {
+ reg = <16>;
+ };
- spi0: spi at 10600 {
- status = "okay";
+ phy1: ethernet-phy at 1 {
+ reg = <17>;
+ };
- spi-flash at 0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "n25q128a13";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <108000000>;
- };
- };
+ phy2: ethernet-phy at 2 {
+ reg = <18>;
+ };
- devbus-bootcs at 10400 {
- status = "okay";
- ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf000000, size 0x1000000 */
-
- /* Device Bus parameters are required */
-
- /* Read parameters */
- devbus,bus-width = <8>;
- devbus,turn-off-ps = <60000>;
- devbus,badr-skew-ps = <0>;
- devbus,acc-first-ps = <124000>;
- devbus,acc-next-ps = <248000>;
- devbus,rd-setup-ps = <0>;
- devbus,rd-hold-ps = <0>;
-
- /* Write parameters */
- devbus,sync-enable = <0>;
- devbus,wr-high-ps = <60000>;
- devbus,wr-low-ps = <60000>;
- devbus,ale-wr-ps = <60000>;
-
- /* NOR 16 MiB */
- nor at 0 {
- compatible = "cfi-flash";
- reg = <0 0x1000000>;
- bank-width = <2>;
+ phy3: ethernet-phy at 3 {
+ reg = <19>;
+ };
};
- };
- pcie-controller {
- status = "okay";
+ ethernet at 70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet at 74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet at 30000 {
+ status = "okay";
+ phy = <&phy2>;
+ phy-mode = "rgmii-id";
+ };
+ ethernet at 34000 {
+ status = "okay";
+ phy = <&phy3>;
+ phy-mode = "rgmii-id";
+ };
- /*
- * The 3 slots are physically present as
- * standard PCIe slots on the board.
- */
- pcie at 1,0 {
- /* Port 0, Lane 0 */
+ spi0: spi at 10600 {
status = "okay";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q128a13";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ };
};
- pcie at 9,0 {
- /* Port 2, Lane 0 */
+
+ devbus-bootcs at 10400 {
status = "okay";
+ ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf000000, size 0x1000000 */
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <8>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+
+ /* NOR 16 MiB */
+ nor at 0 {
+ compatible = "cfi-flash";
+ reg = <0 0x1000000>;
+ bank-width = <2>;
+ };
};
- pcie at 10,0 {
- /* Port 3, Lane 0 */
+
+ pcie-controller {
status = "okay";
+
+ /*
+ * The 3 slots are physically present as
+ * standard PCIe slots on the board.
+ */
+ pcie at 1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ pcie at 9,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ pcie at 10,0 {
+ /* Port 3, Lane 0 */
+ status = "okay";
+ };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
index 12905ab..f8eaa38 100644
--- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
@@ -44,140 +44,142 @@
};
soc {
- pinctrl {
- compatible = "marvell,mv78230-pinctrl";
- reg = <0x18000 0x38>;
-
- sdio_pins: sdio-pins {
- marvell,pins = "mpp30", "mpp31", "mpp32",
- "mpp33", "mpp34", "mpp35";
- marvell,function = "sd0";
+ internal-regs {
+ pinctrl {
+ compatible = "marvell,mv78230-pinctrl";
+ reg = <0x18000 0x38>;
+
+ sdio_pins: sdio-pins {
+ marvell,pins = "mpp30", "mpp31", "mpp32",
+ "mpp33", "mpp34", "mpp35";
+ marvell,function = "sd0";
+ };
};
- };
-
- gpio0: gpio at 18100 {
- compatible = "marvell,orion-gpio";
- reg = <0x18100 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <82>, <83>, <84>, <85>;
- };
-
- gpio1: gpio at 18140 {
- compatible = "marvell,orion-gpio";
- reg = <0x18140 0x40>;
- ngpios = <17>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <87>, <88>, <89>;
- };
- /*
- * MV78230 has 2 PCIe units Gen2.0: One unit can be
- * configured as x4 or quad x1 lanes. One unit is
- * x4/x1.
- */
- pcie-controller {
- compatible = "marvell,armada-xp-pcie";
- status = "disabled";
- device_type = "pci";
-
- #address-cells = <3>;
- #size-cells = <2>;
-
- bus-range = <0x00 0xff>;
-
- ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
- 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
- 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
- 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
- 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
- 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
-
- pcie at 1,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
- reg = <0x0800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 58>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 5>;
- status = "disabled";
+ gpio0: gpio at 18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <82>, <83>, <84>, <85>;
};
- pcie at 2,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
- reg = <0x1000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 59>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 6>;
- status = "disabled";
+ gpio1: gpio at 18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ ngpios = <17>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <87>, <88>, <89>;
};
- pcie at 3,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
- reg = <0x1800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 60>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 7>;
+ /*
+ * MV78230 has 2 PCIe units Gen2.0: One unit can be
+ * configured as x4 or quad x1 lanes. One unit is
+ * x4/x1.
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
status = "disabled";
- };
-
- pcie at 4,0 {
device_type = "pci";
- assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
- reg = <0x2000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 61>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 8>;
- status = "disabled";
- };
- pcie at 9,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
- reg = <0x4800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 99>;
- marvell,pcie-port = <2>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 26>;
- status = "disabled";
+#address-cells = <3>;
+#size-cells = <2>;
+
+ bus-range = <0x00 0xff>;
+
+ ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
+ 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
+ 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
+ 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
+ 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
+ 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+ pcie at 1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+
+ pcie at 2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 59>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 6>;
+ status = "disabled";
+ };
+
+ pcie at 3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+ reg = <0x1800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 60>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 7>;
+ status = "disabled";
+ };
+
+ pcie at 4,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+ reg = <0x2000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 61>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 8>;
+ status = "disabled";
+ };
+
+ pcie at 9,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+ reg = <0x4800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 99>;
+ marvell,pcie-port = <2>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 26>;
+ status = "disabled";
+ };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
index 1faacd1..f4029f0 100644
--- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
@@ -45,177 +45,179 @@
};
soc {
- pinctrl {
- compatible = "marvell,mv78260-pinctrl";
- reg = <0x18000 0x38>;
-
- sdio_pins: sdio-pins {
- marvell,pins = "mpp30", "mpp31", "mpp32",
- "mpp33", "mpp34", "mpp35";
- marvell,function = "sd0";
+ internal-regs {
+ pinctrl {
+ compatible = "marvell,mv78260-pinctrl";
+ reg = <0x18000 0x38>;
+
+ sdio_pins: sdio-pins {
+ marvell,pins = "mpp30", "mpp31", "mpp32",
+ "mpp33", "mpp34", "mpp35";
+ marvell,function = "sd0";
+ };
};
- };
- gpio0: gpio at 18100 {
- compatible = "marvell,orion-gpio";
- reg = <0x18100 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <82>, <83>, <84>, <85>;
- };
+ gpio0: gpio at 18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <82>, <83>, <84>, <85>;
+ };
- gpio1: gpio at 18140 {
- compatible = "marvell,orion-gpio";
- reg = <0x18140 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <87>, <88>, <89>, <90>;
- };
+ gpio1: gpio at 18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <87>, <88>, <89>, <90>;
+ };
- gpio2: gpio at 18180 {
- compatible = "marvell,orion-gpio";
- reg = <0x18180 0x40>;
- ngpios = <3>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <91>;
- };
+ gpio2: gpio at 18180 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18180 0x40>;
+ ngpios = <3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <91>;
+ };
- ethernet at 34000 {
+ ethernet at 34000 {
compatible = "marvell,armada-370-neta";
reg = <0x34000 0x2500>;
interrupts = <14>;
clocks = <&gateclk 1>;
status = "disabled";
- };
-
- /*
- * MV78260 has 3 PCIe units Gen2.0: Two units can be
- * configured as x4 or quad x1 lanes. One unit is
- * x4/x1.
- */
- pcie-controller {
- compatible = "marvell,armada-xp-pcie";
- status = "disabled";
- device_type = "pci";
-
- #address-cells = <3>;
- #size-cells = <2>;
-
- bus-range = <0x00 0xff>;
-
- ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
- 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
- 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
- 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
- 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */
- 0x82000000 0 0x82000 0x82000 0 0x00002000 /* Port 3.0 registers */
- 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
- 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
-
- pcie at 1,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
- reg = <0x0800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 58>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 5>;
- status = "disabled";
};
- pcie at 2,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
- reg = <0x1000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 59>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 6>;
+ /*
+ * MV78260 has 3 PCIe units Gen2.0: Two units can be
+ * configured as x4 or quad x1 lanes. One unit is
+ * x4/x1.
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
status = "disabled";
- };
-
- pcie at 3,0 {
device_type = "pci";
- assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
- reg = <0x1800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 60>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 7>;
- status = "disabled";
- };
- pcie at 4,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
- reg = <0x2000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 61>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 8>;
- status = "disabled";
- };
- pcie at 9,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
- reg = <0x4800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 99>;
- marvell,pcie-port = <2>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 26>;
- status = "disabled";
- };
-
- pcie at 10,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x82000 0 0x2000>;
- reg = <0x5000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 103>;
- marvell,pcie-port = <3>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 27>;
- status = "disabled";
+ bus-range = <0x00 0xff>;
+
+ ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
+ 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
+ 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
+ 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
+ 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */
+ 0x82000000 0 0x82000 0x82000 0 0x00002000 /* Port 3.0 registers */
+ 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
+ 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
+
+ pcie at 1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+
+ pcie at 2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 59>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 6>;
+ status = "disabled";
+ };
+
+ pcie at 3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+ reg = <0x1800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 60>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 7>;
+ status = "disabled";
+ };
+
+ pcie at 4,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+ reg = <0x2000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 61>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 8>;
+ status = "disabled";
+ };
+
+ pcie at 9,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+ reg = <0x4800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 99>;
+ marvell,pcie-port = <2>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 26>;
+ status = "disabled";
+ };
+
+ pcie at 10,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x82000 0 0x2000>;
+ reg = <0x5000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 103>;
+ marvell,pcie-port = <3>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 27>;
+ status = "disabled";
+ };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
index ce4f80a..6ab56bd 100644
--- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
@@ -60,243 +60,245 @@
};
soc {
- pinctrl {
- compatible = "marvell,mv78460-pinctrl";
- reg = <0x18000 0x38>;
+ internal-regs {
+ pinctrl {
+ compatible = "marvell,mv78460-pinctrl";
+ reg = <0x18000 0x38>;
- sdio_pins: sdio-pins {
- marvell,pins = "mpp30", "mpp31", "mpp32",
- "mpp33", "mpp34", "mpp35";
- marvell,function = "sd0";
+ sdio_pins: sdio-pins {
+ marvell,pins = "mpp30", "mpp31", "mpp32",
+ "mpp33", "mpp34", "mpp35";
+ marvell,function = "sd0";
+ };
};
- };
- gpio0: gpio at 18100 {
- compatible = "marvell,orion-gpio";
- reg = <0x18100 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <82>, <83>, <84>, <85>;
- };
+ gpio0: gpio at 18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <82>, <83>, <84>, <85>;
+ };
- gpio1: gpio at 18140 {
- compatible = "marvell,orion-gpio";
- reg = <0x18140 0x40>;
- ngpios = <32>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <87>, <88>, <89>, <90>;
- };
+ gpio1: gpio at 18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <87>, <88>, <89>, <90>;
+ };
- gpio2: gpio at 18180 {
- compatible = "marvell,orion-gpio";
- reg = <0x18180 0x40>;
- ngpios = <3>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupts-cells = <2>;
- interrupts = <91>;
- };
+ gpio2: gpio at 18180 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18180 0x40>;
+ ngpios = <3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupts-cells = <2>;
+ interrupts = <91>;
+ };
- ethernet at 34000 {
+ ethernet at 34000 {
compatible = "marvell,armada-370-neta";
reg = <0x34000 0x2500>;
interrupts = <14>;
clocks = <&gateclk 1>;
status = "disabled";
- };
+ };
- /*
- * MV78460 has 4 PCIe units Gen2.0: Two units can be
- * configured as x4 or quad x1 lanes. Two units are
- * x4/x1.
- */
- pcie-controller {
- compatible = "marvell,armada-xp-pcie";
- status = "disabled";
- device_type = "pci";
+ /*
+ * MV78460 has 4 PCIe units Gen2.0: Two units can be
+ * configured as x4 or quad x1 lanes. Two units are
+ * x4/x1.
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
+ status = "disabled";
+ device_type = "pci";
- #address-cells = <3>;
- #size-cells = <2>;
+ #address-cells = <3>;
+ #size-cells = <2>;
- bus-range = <0x00 0xff>;
+ bus-range = <0x00 0xff>;
- ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
- 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
- 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
- 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
- 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */
- 0x82000000 0 0x82000 0x82000 0 0x00002000 /* Port 3.0 registers */
- 0x82000000 0 0x84000 0x84000 0 0x00002000 /* Port 1.1 registers */
- 0x82000000 0 0x88000 0x88000 0 0x00002000 /* Port 1.2 registers */
- 0x82000000 0 0x8c000 0x8c000 0 0x00002000 /* Port 1.3 registers */
- 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
- 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
+ ranges = <0x82000000 0 0x40000 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0 0x42000 0x42000 0 0x00002000 /* Port 2.0 registers */
+ 0x82000000 0 0x44000 0x44000 0 0x00002000 /* Port 0.1 registers */
+ 0x82000000 0 0x48000 0x48000 0 0x00002000 /* Port 0.2 registers */
+ 0x82000000 0 0x4c000 0x4c000 0 0x00002000 /* Port 0.3 registers */
+ 0x82000000 0 0x80000 0x80000 0 0x00002000 /* Port 1.0 registers */
+ 0x82000000 0 0x82000 0x82000 0 0x00002000 /* Port 3.0 registers */
+ 0x82000000 0 0x84000 0x84000 0 0x00002000 /* Port 1.1 registers */
+ 0x82000000 0 0x88000 0x88000 0 0x00002000 /* Port 1.2 registers */
+ 0x82000000 0 0x8c000 0x8c000 0 0x00002000 /* Port 1.3 registers */
+ 0x82000000 0 0xe0000000 0xe0000000 0 0x08000000 /* non-prefetchable memory */
+ 0x81000000 0 0 0xe8000000 0 0x00100000>; /* downstream I/O */
- pcie at 1,0 {
- device_type = "pci";
- assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
- reg = <0x0800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 58>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 5>;
- status = "disabled";
- };
+ pcie at 1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
- pcie at 2,0 {
- device_type = "pci";
- assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
- reg = <0x1000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 59>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 6>;
- status = "disabled";
- };
+ pcie at 2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 59>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 6>;
+ status = "disabled";
+ };
- pcie at 3,0 {
- device_type = "pci";
- assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
- reg = <0x1800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 60>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 7>;
- status = "disabled";
- };
+ pcie at 3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
+ reg = <0x1800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 60>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 7>;
+ status = "disabled";
+ };
- pcie at 4,0 {
- device_type = "pci";
- assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
- reg = <0x2000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 61>;
- marvell,pcie-port = <0>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 8>;
- status = "disabled";
- };
+ pcie at 4,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
+ reg = <0x2000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 61>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 8>;
+ status = "disabled";
+ };
- pcie at 5,0 {
- device_type = "pci";
- assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
- reg = <0x2800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 62>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 9>;
- status = "disabled";
- };
+ pcie at 5,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+ reg = <0x2800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 62>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 9>;
+ status = "disabled";
+ };
- pcie at 6,0 {
- device_type = "pci";
- assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
- reg = <0x3000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 63>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <1>;
- clocks = <&gateclk 10>;
- status = "disabled";
- };
+ pcie at 6,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
+ reg = <0x3000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 63>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 10>;
+ status = "disabled";
+ };
- pcie at 7,0 {
- device_type = "pci";
- assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
- reg = <0x3800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 64>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <2>;
- clocks = <&gateclk 11>;
- status = "disabled";
- };
+ pcie at 7,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
+ reg = <0x3800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 64>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 11>;
+ status = "disabled";
+ };
- pcie at 8,0 {
- device_type = "pci";
- assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
- reg = <0x4000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 65>;
- marvell,pcie-port = <1>;
- marvell,pcie-lane = <3>;
- clocks = <&gateclk 12>;
- status = "disabled";
- };
- pcie at 9,0 {
- device_type = "pci";
- assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
- reg = <0x4800 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 99>;
- marvell,pcie-port = <2>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 26>;
- status = "disabled";
- };
+ pcie at 8,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
+ reg = <0x4000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 65>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 12>;
+ status = "disabled";
+ };
+ pcie at 9,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
+ reg = <0x4800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 99>;
+ marvell,pcie-port = <2>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 26>;
+ status = "disabled";
+ };
- pcie at 10,0 {
- device_type = "pci";
- assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
- reg = <0x5000 0 0 0 0>;
- #address-cells = <3>;
- #size-cells = <2>;
- #interrupt-cells = <1>;
- ranges;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 103>;
- marvell,pcie-port = <3>;
- marvell,pcie-lane = <0>;
- clocks = <&gateclk 27>;
- status = "disabled";
+ pcie at 10,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
+ reg = <0x5000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 103>;
+ marvell,pcie-port = <3>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 27>;
+ status = "disabled";
+ };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
index e9bc8bf..15a66a8 100644
--- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
+++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
@@ -27,154 +27,156 @@
};
soc {
- serial at 12000 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- serial at 12100 {
- clock-frequency = <250000000>;
- status = "okay";
- };
- pinctrl {
- led_pins: led-pins-0 {
- marvell,pins = "mpp49", "mpp51", "mpp53";
- marvell,function = "gpio";
+ internal-regs {
+ serial at 12000 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
- };
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins>;
-
- red_led {
- label = "red_led";
- gpios = <&gpio1 17 1>;
- default-state = "off";
+ serial at 12100 {
+ clock-frequency = <250000000>;
+ status = "okay";
};
-
- yellow_led {
- label = "yellow_led";
- gpios = <&gpio1 19 1>;
- default-state = "off";
+ pinctrl {
+ led_pins: led-pins-0 {
+ marvell,pins = "mpp49", "mpp51", "mpp53";
+ marvell,function = "gpio";
+ };
};
-
- green_led {
- label = "green_led";
- gpios = <&gpio1 21 1>;
- default-state = "off";
- linux,default-trigger = "heartbeat";
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins>;
+
+ red_led {
+ label = "red_led";
+ gpios = <&gpio1 17 1>;
+ default-state = "off";
+ };
+
+ yellow_led {
+ label = "yellow_led";
+ gpios = <&gpio1 19 1>;
+ default-state = "off";
+ };
+
+ green_led {
+ label = "green_led";
+ gpios = <&gpio1 21 1>;
+ default-state = "off";
+ linux,default-trigger = "heartbeat";
+ };
};
- };
- gpio_keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
- button at 1 {
- label = "Init Button";
- linux,code = <116>;
- gpios = <&gpio1 28 0>;
+ button at 1 {
+ label = "Init Button";
+ linux,code = <116>;
+ gpios = <&gpio1 28 0>;
+ };
};
- };
- mdio {
- phy0: ethernet-phy at 0 {
- reg = <0>;
- };
+ mdio {
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
- phy1: ethernet-phy at 1 {
- reg = <1>;
- };
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
- phy2: ethernet-phy at 2 {
- reg = <2>;
- };
+ phy2: ethernet-phy at 2 {
+ reg = <2>;
+ };
- phy3: ethernet-phy at 3 {
- reg = <3>;
+ phy3: ethernet-phy at 3 {
+ reg = <3>;
+ };
};
- };
- ethernet at 70000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "sgmii";
- };
- ethernet at 74000 {
- status = "okay";
- phy = <&phy1>;
- phy-mode = "sgmii";
- };
- ethernet at 30000 {
- status = "okay";
- phy = <&phy2>;
- phy-mode = "sgmii";
- };
- ethernet at 34000 {
- status = "okay";
- phy = <&phy3>;
- phy-mode = "sgmii";
- };
- i2c at 11000 {
- status = "okay";
- clock-frequency = <400000>;
- };
- i2c at 11100 {
- status = "okay";
- clock-frequency = <400000>;
+ ethernet at 70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "sgmii";
+ };
+ ethernet at 74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "sgmii";
+ };
+ ethernet at 30000 {
+ status = "okay";
+ phy = <&phy2>;
+ phy-mode = "sgmii";
+ };
+ ethernet at 34000 {
+ status = "okay";
+ phy = <&phy3>;
+ phy-mode = "sgmii";
+ };
+ i2c at 11000 {
+ status = "okay";
+ clock-frequency = <400000>;
+ };
+ i2c at 11100 {
+ status = "okay";
+ clock-frequency = <400000>;
- s35390a: s35390a at 30 {
- compatible = "s35390a";
- reg = <0x30>;
+ s35390a: s35390a at 30 {
+ compatible = "s35390a";
+ reg = <0x30>;
+ };
+ };
+ sata at a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+ usb at 50000 {
+ status = "okay";
+ };
+ usb at 51000 {
+ status = "okay";
};
- };
- sata at a0000 {
- nr-ports = <2>;
- status = "okay";
- };
- usb at 50000 {
- status = "okay";
- };
- usb at 51000 {
- status = "okay";
- };
- devbus-bootcs at 10400 {
- status = "okay";
- ranges = <0 0xf0000000 0x8000000>; /* @addr 0xf000000, size 0x8000000 */
-
- /* Device Bus parameters are required */
-
- /* Read parameters */
- devbus,bus-width = <8>;
- devbus,turn-off-ps = <60000>;
- devbus,badr-skew-ps = <0>;
- devbus,acc-first-ps = <124000>;
- devbus,acc-next-ps = <248000>;
- devbus,rd-setup-ps = <0>;
- devbus,rd-hold-ps = <0>;
-
- /* Write parameters */
- devbus,sync-enable = <0>;
- devbus,wr-high-ps = <60000>;
- devbus,wr-low-ps = <60000>;
- devbus,ale-wr-ps = <60000>;
-
- /* NOR 128 MiB */
- nor at 0 {
- compatible = "cfi-flash";
- reg = <0 0x8000000>;
- bank-width = <2>;
+ devbus-bootcs at 10400 {
+ status = "okay";
+ ranges = <0 0xf0000000 0x8000000>; /* @addr 0xf000000, size 0x8000000 */
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <8>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+
+ /* NOR 128 MiB */
+ nor at 0 {
+ compatible = "cfi-flash";
+ reg = <0 0x8000000>;
+ bank-width = <2>;
+ };
};
- };
- pcie-controller {
- status = "okay";
- /* Internal mini-PCIe connector */
- pcie at 1,0 {
- /* Port 0, Lane 0 */
+ pcie-controller {
status = "okay";
+ /* Internal mini-PCIe connector */
+ pcie at 1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
};
};
};
diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/armada-xp.dtsi
index 465b9fa..bacab11 100644
--- a/arch/arm/boot/dts/armada-xp.dtsi
+++ b/arch/arm/boot/dts/armada-xp.dtsi
@@ -22,141 +22,140 @@
model = "Marvell Armada XP family SoC";
compatible = "marvell,armadaxp", "marvell,armada-370-xp";
-
soc {
- L2: l2-cache {
- compatible = "marvell,aurora-system-cache";
- reg = <0x08000 0x1000>;
- cache-id-part = <0x100>;
- wt-override;
- };
+ internal-regs {
+ L2: l2-cache {
+ compatible = "marvell,aurora-system-cache";
+ reg = <0x08000 0x1000>;
+ cache-id-part = <0x100>;
+ wt-override;
+ };
- mpic: interrupt-controller at 20000 {
- reg = <0x20a00 0x2d0>,
- <0x21070 0x58>;
- };
+ mpic: interrupt-controller at 20000 {
+ reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+ };
- armada-370-xp-pmsu at 22000 {
- compatible = "marvell,armada-370-xp-pmsu";
- reg = <0x22100 0x430>,
- <0x20800 0x20>;
- };
+ armada-370-xp-pmsu at 22000 {
+ compatible = "marvell,armada-370-xp-pmsu";
+ reg = <0x22100 0x430>, <0x20800 0x20>;
+ };
- serial at 12200 {
+ serial at 12200 {
compatible = "snps,dw-apb-uart";
reg = <0x12200 0x100>;
reg-shift = <2>;
interrupts = <43>;
reg-io-width = <1>;
status = "disabled";
- };
- serial at 12300 {
+ };
+ serial at 12300 {
compatible = "snps,dw-apb-uart";
reg = <0x12300 0x100>;
reg-shift = <2>;
interrupts = <44>;
reg-io-width = <1>;
status = "disabled";
- };
+ };
- timer at 20300 {
+ timer at 20300 {
marvell,timer-25Mhz;
- };
+ };
- coreclk: mvebu-sar at 18230 {
- compatible = "marvell,armada-xp-core-clock";
- reg = <0x18230 0x08>;
- #clock-cells = <1>;
- };
+ coreclk: mvebu-sar at 18230 {
+ compatible = "marvell,armada-xp-core-clock";
+ reg = <0x18230 0x08>;
+ #clock-cells = <1>;
+ };
- cpuclk: clock-complex at 18700 {
- #clock-cells = <1>;
- compatible = "marvell,armada-xp-cpu-clock";
- reg = <0x18700 0xA0>;
- clocks = <&coreclk 1>;
- };
+ cpuclk: clock-complex at 18700 {
+ #clock-cells = <1>;
+ compatible = "marvell,armada-xp-cpu-clock";
+ reg = <0x18700 0xA0>;
+ clocks = <&coreclk 1>;
+ };
- gateclk: clock-gating-control at 18220 {
- compatible = "marvell,armada-xp-gating-clock";
- reg = <0x18220 0x4>;
- clocks = <&coreclk 0>;
- #clock-cells = <1>;
- };
+ gateclk: clock-gating-control at 18220 {
+ compatible = "marvell,armada-xp-gating-clock";
+ reg = <0x18220 0x4>;
+ clocks = <&coreclk 0>;
+ #clock-cells = <1>;
+ };
- system-controller at 18200 {
+ system-controller at 18200 {
compatible = "marvell,armada-370-xp-system-controller";
reg = <0x18200 0x500>;
- };
+ };
- ethernet at 30000 {
+ ethernet at 30000 {
compatible = "marvell,armada-370-neta";
reg = <0x30000 0x2500>;
interrupts = <12>;
clocks = <&gateclk 2>;
status = "disabled";
- };
-
- xor at 60900 {
- compatible = "marvell,orion-xor";
- reg = <0x60900 0x100
- 0x60b00 0x100>;
- clocks = <&gateclk 22>;
- status = "okay";
-
- xor10 {
- interrupts = <51>;
- dmacap,memcpy;
- dmacap,xor;
};
- xor11 {
- interrupts = <52>;
- dmacap,memcpy;
- dmacap,xor;
- dmacap,memset;
- };
- };
- xor at f0900 {
- compatible = "marvell,orion-xor";
- reg = <0xF0900 0x100
- 0xF0B00 0x100>;
- clocks = <&gateclk 28>;
- status = "okay";
-
- xor00 {
- interrupts = <94>;
- dmacap,memcpy;
- dmacap,xor;
+ xor at 60900 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60900 0x100
+ 0x60b00 0x100>;
+ clocks = <&gateclk 22>;
+ status = "okay";
+
+ xor10 {
+ interrupts = <51>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor11 {
+ interrupts = <52>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
};
- xor01 {
- interrupts = <95>;
- dmacap,memcpy;
- dmacap,xor;
- dmacap,memset;
+
+ xor at f0900 {
+ compatible = "marvell,orion-xor";
+ reg = <0xF0900 0x100
+ 0xF0B00 0x100>;
+ clocks = <&gateclk 28>;
+ status = "okay";
+
+ xor00 {
+ interrupts = <94>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor01 {
+ interrupts = <95>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
};
- };
- usb at 50000 {
- clocks = <&gateclk 18>;
- };
+ usb at 50000 {
+ clocks = <&gateclk 18>;
+ };
- usb at 51000 {
- clocks = <&gateclk 19>;
- };
+ usb at 51000 {
+ clocks = <&gateclk 19>;
+ };
- usb at 52000 {
- compatible = "marvell,orion-ehci";
- reg = <0x52000 0x500>;
- interrupts = <47>;
- clocks = <&gateclk 20>;
- status = "disabled";
- };
+ usb at 52000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x52000 0x500>;
+ interrupts = <47>;
+ clocks = <&gateclk 20>;
+ status = "disabled";
+ };
- thermal at 182b0 {
- compatible = "marvell,armadaxp-thermal";
- reg = <0x182b0 0x4
- 0x184d0 0x4>;
- status = "okay";
+ thermal at 182b0 {
+ compatible = "marvell,armadaxp-thermal";
+ reg = <0x182b0 0x4
+ 0x184d0 0x4>;
+ status = "okay";
+ };
};
};
};
--
1.7.9.5
More information about the devicetree-discuss
mailing list