[PATCH v2] ata: add platform driver for Calxeda AHCI controller
Mark Langsdorf
mark.langsdorf at calxeda.com
Fri Sep 7 07:03:30 EST 2012
Calxeda highbank SATA phy has intermittent problems bringing up a link
with Gen3 drives. Retrying the phy hard reset can work-around this issue,
but each reset also disables spread spectrum support. The reset function
also needs to reprogram the phy to enable spread spectrum support.
Create a new driver based on ahci_platform to support the Calxeda Highbank
SATA controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf at calxeda.com>
Signed-off-by: Rob Herring <rob.herring at calxeda.com>
---
Changes from v1
used to be the second patch in a 2 part series; first patch was accepted
and this patch's name was changed from "ahci_platform: add custom
hard reset for Calxeda ahci ctrlr"
Refactored all of sata_highbank so it is a stand-alone driver based on
ahci_platform
Driver can now be loaded as a module
Driver is no longer auto-selected as part of ARCH_HIGHBANK
.../devicetree/bindings/arm/calxeda/combophy.txt | 17 +
.../devicetree/bindings/ata/ahci-platform.txt | 8 +
arch/arm/boot/dts/highbank.dts | 17 +
drivers/ata/Kconfig | 8 +
drivers/ata/Makefile | 1 +
drivers/ata/ahci_platform.c | 1 -
drivers/ata/sata_highbank.c | 450 +++++++++++++++++++++
7 files changed, 501 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/arm/calxeda/combophy.txt
create mode 100644 drivers/ata/sata_highbank.c
diff --git a/Documentation/devicetree/bindings/arm/calxeda/combophy.txt b/Documentation/devicetree/bindings/arm/calxeda/combophy.txt
new file mode 100644
index 0000000..6622bdb
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/calxeda/combophy.txt
@@ -0,0 +1,17 @@
+Calxeda Highbank Combination Phys for SATA
+
+Properties:
+- compatible : Should be "calxeda,hb-combophy"
+- #phy-cells: Should be 1.
+- reg : Address and size for Combination Phy registers.
+- phydev: device ID for programming the combophy.
+
+Example:
+
+ combophy5: combo-phy at fff5d000 {
+ compatible = "calxeda,hb-combophy";
+ #phy-cells = <1>;
+ reg = <0xfff5d000 0x1000>;
+ phydev = <31>;
+ };
+
diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt
index 8bb8a76..147c1f6 100644
--- a/Documentation/devicetree/bindings/ata/ahci-platform.txt
+++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt
@@ -8,9 +8,17 @@ Required properties:
- interrupts : <interrupt mapping for SATA IRQ>
- reg : <registers mapping>
+Optional properties:
+- calxeda,port-phys: phandle-combophy and lane assignment, which maps each
+ SATA port to a combophy and a lane within that
+ combophy
+
Example:
sata at ffe08000 {
compatible = "calxeda,hb-ahci";
reg = <0xffe08000 0x1000>;
interrupts = <115>;
+ calxeda,port-phys = <&combophy5 0 &combophy0 0 &combophy0 1
+ &combophy0 2 &combophy0 3>;
+
};
diff --git a/arch/arm/boot/dts/highbank.dts b/arch/arm/boot/dts/highbank.dts
index 9fecf1a..5204cf7 100644
--- a/arch/arm/boot/dts/highbank.dts
+++ b/arch/arm/boot/dts/highbank.dts
@@ -121,6 +121,9 @@
compatible = "calxeda,hb-ahci";
reg = <0xffe08000 0x10000>;
interrupts = <0 83 4>;
+ calxeda,port-phys = <&combophy5 0 &combophy0 0
+ &combophy0 1 &combophy0 2
+ &combophy0 3>;
};
sdhci at ffe0e000 {
@@ -306,5 +309,19 @@
reg = <0xfff51000 0x1000>;
interrupts = <0 80 4 0 81 4 0 82 4>;
};
+
+ combophy0: combo-phy at fff58000 {
+ compatible = "calxeda,hb-combophy";
+ #phy-cells = <1>;
+ reg = <0xfff58000 0x1000>;
+ phydev = <5>;
+ };
+
+ combophy5: combo-phy at fff5d000 {
+ compatible = "calxeda,hb-combophy";
+ #phy-cells = <1>;
+ reg = <0xfff5d000 0x1000>;
+ phydev = <31>;
+ };
};
};
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 27cecd3..e08d322 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -214,6 +214,14 @@ config SATA_DWC_VDEBUG
help
This option enables the taskfile dumping and NCQ debugging.
+config SATA_HIGHBANK
+ tristate "Calxeda Highbank SATA support"
+ help
+ This option enables support for the Calxeda Highbank SoC's
+ onboard SATA.
+
+ If unsure, say N.
+
config SATA_MV
tristate "Marvell SATA support"
help
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index a454a13..8b384f1 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_SATA_FSL) += sata_fsl.o
obj-$(CONFIG_SATA_INIC162X) += sata_inic162x.o
obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o
+obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o
# SFF w/ custom DMA
obj-$(CONFIG_PDC_ADMA) += pdc_adma.o
diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
index 09728e0..dc187c7 100644
--- a/drivers/ata/ahci_platform.c
+++ b/drivers/ata/ahci_platform.c
@@ -277,7 +277,6 @@ static int ahci_resume(struct device *dev)
SIMPLE_DEV_PM_OPS(ahci_pm_ops, ahci_suspend, ahci_resume);
static const struct of_device_id ahci_of_match[] = {
- { .compatible = "calxeda,hb-ahci", },
{ .compatible = "snps,spear-ahci", },
{},
};
diff --git a/drivers/ata/sata_highbank.c b/drivers/ata/sata_highbank.c
new file mode 100644
index 0000000..0d7c4c2
--- /dev/null
+++ b/drivers/ata/sata_highbank.c
@@ -0,0 +1,450 @@
+/*
+ * Calxeda Highbank AHCI SATA platform driver
+ * Copyright 2012 Calxeda, Inc.
+ *
+ * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/kernel.h>
+#include <linux/gfp.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/spinlock.h>
+#include <linux/device.h>
+#include <linux/of_device.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/libata.h>
+#include <linux/ahci_platform.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/export.h>
+#include "ahci.h"
+
+#define CPHY_MAP(dev, addr) ((((dev) & 0x1f) << 7) | (((addr) >> 9) & 0x7f))
+#define CPHY_ADDR(addr) (((addr) & 0x1ff) << 2)
+#define SERDES_CR_CTL 0x80a0
+#define SERDES_CR_ADDR 0x80a1
+#define SERDES_CR_DATA 0x80a2
+#define CR_BUSY 0x0001
+#define CR_START 0x0001
+#define CR_WR_RDN 0x0002
+#define CPHY_RX_INPUT_STS 0x2002
+#define CPHY_SATA_OVERRIDE 0x4000
+#define CPHY_OVERRIDE 0x2005
+#define SPHY_LANE 0x100
+#define SPHY_HALF_RATE 0x0001
+#define CPHY_SATA_DPLL_MODE 0x0700
+#define CPHY_SATA_DPLL_SHIFT 8
+#define CPHY_SATA_DPLL_RESET (1 << 11)
+#define CPHY_PHY_COUNT 6
+#define CPHY_LANE_COUNT 4
+#define CPHY_PORT_COUNT (CPHY_PHY_COUNT * CPHY_LANE_COUNT)
+
+static DEFINE_SPINLOCK(cphy_lock);
+/* Each of the 6 phys can have up to 4 sata ports attached to i. Map 0-based
+ * sata ports to their phys and then to their lanes within the phys
+ */
+struct phy_lane_info {
+ void __iomem *phy_base;
+ u8 lane_mapping;
+ u8 phy_devs;
+};
+static struct phy_lane_info port_data[CPHY_PORT_COUNT];
+
+static u32 __combo_phy_reg_read(u8 sata_port, u32 addr)
+{
+ u32 data;
+ u8 dev = port_data[sata_port].phy_devs;
+ spin_lock(&cphy_lock);
+ writel(CPHY_MAP(dev, addr), port_data[sata_port].phy_base + 0x800);
+ data = readl(port_data[sata_port].phy_base + CPHY_ADDR(addr));
+ spin_unlock(&cphy_lock);
+ return data;
+}
+
+static void __combo_phy_reg_write(u8 sata_port, u32 addr, u32 data)
+{
+ u8 dev = port_data[sata_port].phy_devs;
+ spin_lock(&cphy_lock);
+ writel(CPHY_MAP(dev, addr), port_data[sata_port].phy_base + 0x800);
+ writel(data, port_data[sata_port].phy_base + CPHY_ADDR(addr));
+ spin_unlock(&cphy_lock);
+}
+
+static void combo_phy_wait_for_ready(u8 sata_port)
+{
+ while (__combo_phy_reg_read(sata_port, SERDES_CR_CTL) & CR_BUSY)
+ udelay(5);
+}
+
+static u32 combo_phy_read(u8 sata_port, u32 addr)
+{
+ combo_phy_wait_for_ready(sata_port);
+ __combo_phy_reg_write(sata_port, SERDES_CR_ADDR, addr);
+ __combo_phy_reg_write(sata_port, SERDES_CR_CTL, CR_START);
+ combo_phy_wait_for_ready(sata_port);
+ return __combo_phy_reg_read(sata_port, SERDES_CR_DATA);
+}
+
+static void combo_phy_write(u8 sata_port, u32 addr, u32 data)
+{
+ combo_phy_wait_for_ready(sata_port);
+ __combo_phy_reg_write(sata_port, SERDES_CR_ADDR, addr);
+ __combo_phy_reg_write(sata_port, SERDES_CR_DATA, data);
+ __combo_phy_reg_write(sata_port, SERDES_CR_CTL, CR_WR_RDN | CR_START);
+}
+
+static void highbank_cphy_disable_overrides(u8 sata_port)
+{
+ u8 lane = port_data[sata_port].lane_mapping;
+ u32 tmp;
+ if (unlikely(port_data[sata_port].phy_base == NULL))
+ return;
+ tmp = combo_phy_read(sata_port, CPHY_RX_INPUT_STS + lane * SPHY_LANE);
+ tmp &= ~CPHY_SATA_OVERRIDE;
+ combo_phy_write(sata_port, CPHY_OVERRIDE + lane * SPHY_LANE, tmp);
+}
+
+static void cphy_override_rx_mode(u8 sata_port, u32 val)
+{
+ u8 lane = port_data[sata_port].lane_mapping;
+ u32 tmp;
+ tmp = combo_phy_read(sata_port, CPHY_RX_INPUT_STS + lane * SPHY_LANE);
+ tmp &= ~CPHY_SATA_OVERRIDE;
+ combo_phy_write(sata_port, CPHY_OVERRIDE + lane * SPHY_LANE, tmp);
+
+ tmp |= CPHY_SATA_OVERRIDE;
+ combo_phy_write(sata_port, CPHY_OVERRIDE + lane * SPHY_LANE, tmp);
+
+ tmp &= ~CPHY_SATA_DPLL_MODE;
+ tmp |= val << CPHY_SATA_DPLL_SHIFT;
+ combo_phy_write(sata_port, CPHY_OVERRIDE + lane * SPHY_LANE, tmp);
+
+ tmp |= CPHY_SATA_DPLL_RESET;
+ combo_phy_write(sata_port, CPHY_OVERRIDE + lane * SPHY_LANE, tmp);
+
+ tmp &= ~CPHY_SATA_DPLL_RESET;
+ combo_phy_write(sata_port, CPHY_OVERRIDE + lane * SPHY_LANE, tmp);
+
+ msleep(15);
+}
+
+static void highbank_cphy_override_lane(u8 sata_port)
+{
+ u8 lane = port_data[sata_port].lane_mapping;
+ u32 tmp, k = 0;
+
+ if (unlikely(port_data[sata_port].phy_base == NULL))
+ return;
+ do {
+ tmp = combo_phy_read(sata_port, CPHY_RX_INPUT_STS +
+ lane * SPHY_LANE);
+ } while ((tmp & SPHY_HALF_RATE) && (k++ < 1000));
+ cphy_override_rx_mode(sata_port, 3);
+}
+
+static int highbank_initialize_phys(struct device *dev, void __iomem *addr)
+{
+ struct device_node *sata_node = dev->of_node;
+ int phy_count = 0, phy, port = 0;
+ void __iomem *cphy_base[CPHY_PHY_COUNT];
+ struct device_node *phy_nodes[CPHY_PHY_COUNT];
+ memset(port_data, 0, sizeof(struct phy_lane_info) * CPHY_PORT_COUNT);
+ memset(phy_nodes, 0, sizeof(struct device_node*) * CPHY_PHY_COUNT);
+
+ do {
+ u32 tmp;
+ struct of_phandle_args phy_data;
+ if (of_parse_phandle_with_args(sata_node,
+ "calxeda,port-phys", "#phy-cells",
+ port, &phy_data))
+ break;
+ for (phy = 0; phy < phy_count; phy++) {
+ if (phy_nodes[phy] == phy_data.np)
+ break;
+ }
+ if (phy_nodes[phy] == NULL) {
+ phy_nodes[phy] = phy_data.np;
+ cphy_base[phy] = of_iomap(phy_nodes[phy], 0);
+ if (cphy_base[phy] == NULL) {
+ return 0;
+ }
+ phy_count += 1;
+ }
+ port_data[port].lane_mapping = phy_data.args[0];
+ of_property_read_u32(phy_nodes[phy], "phydev", &tmp);
+ port_data[port].phy_devs = tmp;
+ port_data[port].phy_base = cphy_base[phy];
+ of_node_put(phy_data.np);
+ port += 1;
+ } while (port < CPHY_PORT_COUNT);
+ return 0;
+}
+
+static int ahci_highbank_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
+{
+ const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
+ struct ata_port *ap = link->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+ struct ata_taskfile tf;
+ bool online;
+ u32 sstatus;
+ int rc;
+ int retry = 10;
+
+ ahci_stop_engine(ap);
+
+ /* clear D2H reception area to properly wait for D2H FIS */
+ ata_tf_init(link->device, &tf);
+ tf.command = 0x80;
+ ata_tf_to_fis(&tf, 0, 0, d2h_fis);
+
+ do {
+ highbank_cphy_disable_overrides(link->ap->port_no);
+ rc = sata_link_hardreset(link, timing, deadline, &online, NULL);
+ highbank_cphy_override_lane(link->ap->port_no);
+
+ /* If the status is 1, we are connected, but the link did not
+ * come up. So retry resetting the link again.
+ */
+ if (sata_scr_read(link, SCR_STATUS, &sstatus))
+ break;
+ if (!(sstatus & 0x3))
+ break;
+ } while (!online && retry--);
+
+ ahci_start_engine(ap);
+
+ if (online)
+ *class = ahci_dev_classify(ap);
+
+ return rc;
+}
+
+static struct ata_port_operations ahci_highbank_ops = {
+ .inherits = &ahci_ops,
+ .hardreset = ahci_highbank_hardreset,
+};
+
+static const struct ata_port_info ahci_highbank_port_info = {
+ .flags = AHCI_FLAG_COMMON,
+ .pio_mask = ATA_PIO4,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &ahci_highbank_ops,
+};
+
+static struct scsi_host_template ahci_highbank_platform_sht = {
+ AHCI_SHT("highbank-ahci"),
+};
+
+static const struct of_device_id ahci_of_match[] = {
+ { .compatible = "calxeda,hb-ahci" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ahci_of_match);
+
+static int __init ahci_highbank_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ahci_host_priv *hpriv;
+ struct ata_host *host;
+ struct resource *mem;
+ int irq;
+ int n_ports;
+ int i;
+ int rc;
+ struct ata_port_info pi = ahci_highbank_port_info;
+ const struct ata_port_info *ppi[] = { &pi, NULL };
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!mem) {
+ dev_err(dev, "no mmio space\n");
+ return -EINVAL;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq <= 0) {
+ dev_err(dev, "no irq\n");
+ return -EINVAL;
+ }
+
+ hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL);
+ if (!hpriv) {
+ dev_err(dev, "can't alloc ahci_host_priv\n");
+ return -ENOMEM;
+ }
+
+ hpriv->flags |= (unsigned long)pi.private_data;
+
+ hpriv->mmio = devm_ioremap(dev, mem->start, resource_size(mem));
+ if (!hpriv->mmio) {
+ dev_err(dev, "can't map %pR\n", mem);
+ return -ENOMEM;
+ }
+
+ rc = highbank_initialize_phys(dev, hpriv->mmio);
+ if (rc)
+ return rc;
+
+
+ ahci_save_initial_config(dev, hpriv, 0, 0);
+
+ /* prepare host */
+ if (hpriv->cap & HOST_CAP_NCQ)
+ pi.flags |= ATA_FLAG_NCQ;
+
+ if (hpriv->cap & HOST_CAP_PMP)
+ pi.flags |= ATA_FLAG_PMP;
+
+ ahci_set_em_messages(hpriv, &pi);
+
+ /* CAP.NP sometimes indicate the index of the last enabled
+ * port, at other times, that of the last possible port, so
+ * determining the maximum port number requires looking at
+ * both CAP.NP and port_map.
+ */
+ n_ports = max(ahci_nr_ports(hpriv->cap), fls(hpriv->port_map));
+
+ host = ata_host_alloc_pinfo(dev, ppi, n_ports);
+ if (!host) {
+ rc = -ENOMEM;
+ goto err0;
+ }
+
+ host->private_data = hpriv;
+
+ if (!(hpriv->cap & HOST_CAP_SSS) || ahci_ignore_sss)
+ host->flags |= ATA_HOST_PARALLEL_SCAN;
+
+ if (pi.flags & ATA_FLAG_EM)
+ ahci_reset_em(host);
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap = host->ports[i];
+
+ ata_port_desc(ap, "mmio %pR", mem);
+ ata_port_desc(ap, "port 0x%x", 0x100 + ap->port_no * 0x80);
+
+ /* set enclosure management message type */
+ if (ap->flags & ATA_FLAG_EM)
+ ap->em_message_type = hpriv->em_msg_type;
+
+ /* disabled/not-implemented port */
+ if (!(hpriv->port_map & (1 << i)))
+ ap->ops = &ata_dummy_port_ops;
+ }
+
+ rc = ahci_reset_controller(host);
+ if (rc)
+ goto err0;
+
+ ahci_init_controller(host);
+ ahci_print_info(host, "platform");
+
+ rc = ata_host_activate(host, irq, ahci_interrupt, 0,
+ &ahci_highbank_platform_sht);
+ if (rc)
+ goto err0;
+
+ return 0;
+err0:
+ return rc;
+}
+
+static int __devexit ahci_highbank_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ata_host *host = dev_get_drvdata(dev);
+
+ ata_host_detach(host);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int ahci_highbank_suspend(struct device *dev)
+{
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct ahci_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->mmio;
+ u32 ctl;
+ int rc;
+
+ if (hpriv->flags & AHCI_HFLAG_NO_SUSPEND) {
+ dev_err(dev, "firmware update required for suspend/resume\n");
+ return -EIO;
+ }
+
+ /*
+ * AHCI spec rev1.1 section 8.3.3:
+ * Software must disable interrupts prior to requesting a
+ * transition of the HBA to D3 state.
+ */
+ ctl = readl(mmio + HOST_CTL);
+ ctl &= ~HOST_IRQ_EN;
+ writel(ctl, mmio + HOST_CTL);
+ readl(mmio + HOST_CTL); /* flush */
+
+ rc = ata_host_suspend(host, PMSG_SUSPEND);
+ if (rc)
+ return rc;
+
+ return 0;
+}
+
+static int ahci_highbank_resume(struct device *dev)
+{
+ struct ata_host *host = dev_get_drvdata(dev);
+ int rc;
+
+ if (dev->power.power_state.event == PM_EVENT_SUSPEND) {
+ rc = ahci_reset_controller(host);
+ if (rc)
+ return rc;
+
+ ahci_init_controller(host);
+ }
+
+ ata_host_resume(host);
+
+ return 0;
+}
+#endif
+
+SIMPLE_DEV_PM_OPS(ahci_highbank_pm_ops,
+ ahci_highbank_suspend, ahci_highbank_resume);
+
+static struct platform_driver ahci_highbank_driver = {
+ .remove = __devexit_p(ahci_highbank_remove),
+ .driver = {
+ .name = "highbank-ahci",
+ .owner = THIS_MODULE,
+ .of_match_table = ahci_of_match,
+ .pm = &ahci_highbank_pm_ops,
+ },
+ .probe = ahci_highbank_probe,
+};
+
+module_platform_driver(ahci_highbank_driver);
+
+MODULE_DESCRIPTION("Calxeda Highbank AHCI SATA platform driver");
+MODULE_AUTHOR("Mark Langsdorf <mark.langsdorf at calxeda.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("sata:highbank");
--
1.7.11.4
More information about the devicetree-discuss
mailing list