[PATCH RESEND v4 2/3] arm/dts: AM33XX: Configure pinmuxs for user leds control on Bone

AnilKumar, Chimata anilkumar at ti.com
Sat Sep 1 17:01:09 EST 2012


Hi Koen,

On Fri, Aug 31, 2012 at 21:23:18, Koen Kooi wrote:
> 
> Op 30 aug. 2012, om 22:35 heeft Tony Lindgren <tony at atomide.com> het volgende geschreven:
> 
> > * AnilKumar Ch <anilkumar at ti.com> [120828 01:11]:
> >> Adds GPIO pinctrl nodes to am3358_pinmux master node to control
> >> user leds (USR0, USR1, USR2 and USR3) present on BeagleBone.
> >> 
> >> Signed-off-by: AnilKumar Ch <anilkumar at ti.com>
> >> ---
> >> arch/arm/boot/dts/am335x-bone.dts |   14 ++++++++++++++
> >> 1 file changed, 14 insertions(+)
> >> 
> >> diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts
> >> index a7906cb..58f5042 100644
> >> --- a/arch/arm/boot/dts/am335x-bone.dts
> >> +++ b/arch/arm/boot/dts/am335x-bone.dts
> >> @@ -18,6 +18,20 @@
> >> 		reg = <0x80000000 0x10000000>; /* 256 MB */
> >> 	};
> >> 
> >> +	am3358_pinmux: pinmux at 44E10800 {
> >> +		pinctrl-names = "default";
> >> +		pinctrl-0 = <&userled_pins>;
> >> +
> >> +		userled_pins: pinmux_userled_pins {
> >> +			pinctrl-single,pins = <
> >> +				0x54 0x7	/* gpmc_a5.gpio1_21, OUTPUT | MODE7 */
> >> +				0x58 0x17	/* gpmc_a6.gpio1_22, OUTPUT_PULLUP | MODE7 */
> >> +				0x5C 0x7	/* gpmc_a7.gpio1_23, OUTPUT | MODE7 */
> >> +				0x60 0x17	/* gpmc_a8.gpio1_24, OUTPUT_PULLUP | MODE7 */
> >> +			>;
> >> +		};
> >> +	};
> >> +
> > 
> > Looks like this patch should also claim these pins by the led driver.
> > Then the led driver should just do pinctrl_get_select_default(&pdev->dev)
> > in it's probe function to set the pins.
> 
> FWIW, I've been using this for a while now:
> 
> +       leds {
> +               compatible = "gpio-leds";
> +               heartbeat {
> +                       label = "beaglebone::usr0";
> +                       gpios = <&gpio2 21 0>;
> +                       linux,default-trigger = "heartbeat";
> +               };
> +
> +               mmc {
> +                       label = "beaglebone:usr1";
> +                       gpios = <&gpio2 22 0>;
> +                       linux,default-trigger = "mmc0";
> +               };

Thanks for the inputs, similar data but not exact is added to
v5 series.

+		gpio-leds {
+			compatible = "gpio-leds";
+			pinctrl-names = "default";
+			pinctrl-0 = <&userled_pins>;
+
+			led0 {
+				label = "status:green:user0";
+				gpios = <&gpio2 21 0>;
+				default-state = "off";
+			};
+
+			led1 {
+				label = "status:green:user1";
+				gpios = <&gpio2 22 0>;
+				default-state = "off";
+			};
+
+			led2 {
+				label = "status:green:user2";
+				gpios = <&gpio2 23 0>;
+				default-state = "off";
+			};
+
+			led3 {
+				label = "status:green:user3";
+				gpios = <&gpio2 24 0>;
+				default-state = "off";
+			};
+		};
+

Can you review my v5 patches and tell me if there are any
modifications/changes required?

Thanks
AnilKumar


More information about the devicetree-discuss mailing list