[PATCH 1/2] of: add helper to parse display specs

[Mitch Bradley]

On 10/1/2012 6:53 AM, Stephen Warren wrote:
> On 09/24/2012 09:35 AM, Steffen Trumtrar wrote:
>> Parse a display-node with timings and hardware-specs from devictree.
> 
>> diff --git a/Documentation/devicetree/bindings/video/display b/Documentation/devicetree/bindings/video/display
>> new file mode 100644
>> index 0000000..722766a
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/video/display
> 
> This should be display.txt.
> 
>> @@ -0,0 +1,208 @@
>> +display bindings
>> +==================
>> +
>> +display-node
>> +------------
> 
> I'm not personally convinced about the direction this is going. While I
> think it's reasonable to define DT bindings for displays, and DT
> bindings for display modes, I'm not sure that it's reasonable to couple
> them together into a single binding.
> 
> I think creating a well-defined timing binding first will be much
> simpler than doing so within the context of a display binding; the
> scope/content of a general display binding seems much less well-defined
> to me at least, for reasons I mentioned before.
> 
>> +required properties:
>> + - none
>> +
>> +optional properties:
>> + - default-timing: the default timing value
>> + - width-mm, height-mm: Display dimensions in mm
> 
>> + - hsync-active-high (bool): Hsync pulse is active high
>> + - vsync-active-high (bool): Vsync pulse is active high
> 
> At least those two properties should exist in the display timing instead
> (or perhaps as well). There are certainly cases where different similar
> display modes are differentiated by hsync/vsync polarity more than
> anything else. This is probably more likely with analog display
> connectors than digital, but I see no reason why a DT binding for
> display timing shouldn't cover both.
> 
>> + - de-active-high (bool): Data-Enable pulse is active high
>> + - pixelclk-inverted (bool): pixelclock is inverted
> 
>> + - pixel-per-clk
> 
> pixel-per-clk is probably something that should either be part of the
> timing definition, or something computed internally to the display
> driver based on rules for the signal type, rather than something
> represented in DT.
> 
> The above comment assumes this property is intended to represent DVI's
> requirement for pixel clock doubling for low-pixel-clock-rate modes. If
> it's something to do with e.g. a single-data-rate vs. double-data-rate
> property of the underlying physical connection, that's most likely
> something that should be defined in a binding specific to e.g. LVDS,
> rather than something generic.
> 
>> + - link-width: number of channels (e.g. LVDS)
>> + - bpp: bits-per-pixel
>> +
>> +timings-subnode
>> +---------------
>> +
>> +required properties:
>> +subnodes that specify
>> + - hactive, vactive: Display resolution
>> + - hfront-porch, hback-porch, hsync-len: Horizontal Display timing parameters
>> +   in pixels
>> +   vfront-porch, vback-porch, vsync-len: Vertical display timing parameters in
>> +   lines
>> + - clock: displayclock in Hz
>> +
>> +There are different ways of describing a display and its capabilities. The devicetree
>> +representation corresponds to the one commonly found in datasheets for displays.
>> +The description of the display and its timing is split in two parts: first the display
>> +properties like size in mm and (optionally) multiple subnodes with the supported timings.
>> +If a display supports multiple signal timings, the default-timing can be specified.
>> +
>> +Example:
>> +
>> +	display at 0 {
>> +		width-mm = <800>;
>> +		height-mm = <480>;
>> +		default-timing = <&timing0>;
>> +		timings {
>> +			timing0: timing at 0 {
> 
> If you're going to use a unit address ("@0") to ensure that node names
> are unique (which is not mandatory), then each node also needs a reg
> property with matching value, and #address-cells/#size-cells in the
> parent. Instead, you could name the nodes something unique based on the
> mode name to avoid this, e.g. 1080p24 { ... }.


I'm concerned that numbered nodes are being misused as arrays.

It's easy to make real arrays by including multiple cells in the value
of each timing parameter, and easy to choose a cell by saying the array
index instead of using the phandle.



> 
> _______________________________________________
> devicetree-discuss mailing list
> devicetree-discuss at lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/devicetree-discuss
>