[PATCH v3 4/4] ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND

Philip, Avinash avinashphilip at ti.com
Wed Nov 28 16:01:30 EST 2012


On Tue, Nov 27, 2012 at 19:30:54, Daniel Mack wrote:
> Hi Avinash,
> Hi Peter,
> 
> On 23.11.2012 11:43, Philip, Avinash wrote:
> > On Wed, Nov 21, 2012 at 15:45:23, Daniel Mack wrote:
> >> On 20.11.2012 16:59, Peter Korsgaard wrote:
> >>>>>>>> "Daniel" == Daniel Mack <zonque at gmail.com> writes:
> 
> > Peter,
> > 
> > In patch [1], mtd: nand: omap2: Support for hardware BCH
> > 
> > ecc_layout made compatible with Rom Boot Loader ECC layout for am335x.
> > 
> > This action is based on is_elm_used flag.
> > 
> > Requirement of this flag is to identify the whether the platform
> > ELM module & based on this configure ELM module if present.
> > 
> > But ideally BCH8 ecc lay out didn't have a dependency on ELM, it
> > can work with software BCH ecc. RBL compatibility is missing
> > in software BCH because of addition of constant polynomial to
> > ecc vector. If we remove the dependency on erased page handling
> > by ecc vector with constant polynomial, software BCH can do the
> > job of RBL compatibility.
> > 
> > Ivan,
> > Do you have any suggestions?
> > Discussion for RBL compatibility found at [2].
> > 
> > It is good that software BCH also support RBL compatibility by suppressing
> > constant polynomial modification. Then ecc layout can be selected from
> > DT entry and error correction can be chosen between software/hardware
> > depending on the availability of ELM hardware.
> > Currently RBL BCH8 compatibility depends on the availability of ELM
> > hardware. Later once software BCH start supporting RBL compatibility,
> > we can remove  the check.
> > 
> >>
> >> That is what I experienced, yes. The kernel was unable to parse NAND
> >> pages that were written from U-Boot with bch8 hardware mode when the elm
> >> module was not active. Maybe someone from TI can explain that? Giving it
> >> a dedicated name would also solve the problem with the extra DT property.
> > 
> > Daniel,
> > 
> > Currently BCH8 is supported with software ecc error correction in mainline.
> > The layout for BCH8 ECC layout is
> > 0-1 -> BAD block markers
> > 2-11-> oob free area
> > 12-63-> BCH8 ECC.
> > 
> > RBL ECC layout is
> > 0-1 -> BAD block markers
> > 2-57-> BCH8 ecc layout
> > 58-63-> OOB free area
> > 
> > As u-boot also maintain RBL ecc layout, write from U-boot
> > and read from Linux requires compatibility with RBL ecc layout.
> > The same is achieved in the patch [1], with by setting is_elm_used
> > to true.
> > 
> > 1. https://lkml.org/lkml/2012/10/31/87
> > 2. https://lkml.org/lkml/2012/10/11/20
> 
> So, after reading this, I'm still uncertain what's your preferred way of
> handling the bindings here. Are you saying we should stick with the
> is_elm_used flag, and subsequently care for BCH8 software mode
> compatibility?

Ideally RBL compatibility didn't depend on the availability of ELM module. So
from am335x perspective, RBL compatibility is achieved with ECC error correction
with ELM module. I would submit one more revision of BCH8 ELM error correction
support which would check for bch8-am335xrbl-compatible.
Note: RBL ecc layout can vary from SOC to SOC

Daniel,

So can you start supporting "bch8-am335xrbl-compatible" and remove usage of
is_elm_used in dt. This should come in ecc_opt field.

In omap2 NAND driver, AM335x RBL compatibility is achieved depending on ecc_layout
and runtime detection of elm module. So options related to can be
1. bch8-am335xrbl-compatible is enabled and run time detection of
   Of elm module passed, RBL compatibility achieved.
2. bch8-am335xrbl-compatible is enabled and run time detection of
   of elm module failed, RBL compatibility sacrificed but continue with
   software BCH8 error correction. Sacrificing RBL compatibility
   because of constant polynomial addition and usage of 14 byte instead of 13 byte.

Ivan,
Do you have any plan of removing addition of constant polynomial to ecc data
and go for extra byte checking to find erased pages?
This way we can start support BCH8 with RBL compatible and kernel
Didn't put any restriction of the ecc layout.

Thanks
Avinash

> 
> I would like to submit a new version soon, so it can be queued up for
> the next merge window, and that decision is the last blocker currently
> for sending out a new series.
> 
> 
> Many thanks,
> Daniel
> 
> 



More information about the devicetree-discuss mailing list