[PATCH 1/7] clk: mvebu: add mvebu core clocks.
Andrew Lunn
andrew at lunn.ch
Fri Nov 16 08:28:20 EST 2012
From: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
This driver allows to provide DT clocks for core clocks found on
Marvell Kirkwood, Dove & 370/XP SoCs. The core clock frequencies and
ratios are determined by decoding the Sample-At-Reset registers.
Although technically correct, using a divider of 0 will lead to
div_by_zero panic. Let's use a ratio of 0/1 instead to fail later
with a zero clock.
Signed-off-by: Gregory CLEMENT <gregory.clement at free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
Signed-off-by: Andrew Lunn <andrew at lunn.ch>
---
.../devicetree/bindings/clock/mvebu-core-clock.txt | 47 ++
drivers/clk/Kconfig | 2 +
drivers/clk/Makefile | 1 +
drivers/clk/mvebu/Kconfig | 3 +
drivers/clk/mvebu/Makefile | 1 +
drivers/clk/mvebu/clk-core.c | 675 ++++++++++++++++++++
drivers/clk/mvebu/clk-core.h | 18 +
drivers/clk/mvebu/clk.c | 23 +
include/linux/clk/mvebu.h | 22 +
9 files changed, 792 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/mvebu-core-clock.txt
create mode 100644 drivers/clk/mvebu/Kconfig
create mode 100644 drivers/clk/mvebu/Makefile
create mode 100644 drivers/clk/mvebu/clk-core.c
create mode 100644 drivers/clk/mvebu/clk-core.h
create mode 100644 drivers/clk/mvebu/clk.c
create mode 100644 include/linux/clk/mvebu.h
diff --git a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt
new file mode 100644
index 0000000..84cfae7
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt
@@ -0,0 +1,47 @@
+* Core Clock bindings for Marvell MVEBU SoCs
+
+Marvell MVEBU SoCs usually allow to determine core clock frequencies by
+reading the Sample-At-Reset (SAR) register. The core clock consumer should
+specify the desired clock by having the clock ID in its "clocks" phandle cell.
+
+The following is a list of provided IDs and clock names on Kirkwood and Dove:
+ 0 = tclk (Internal Bus clock)
+ 1 = cpuclk (CPU0 clock)
+ 2 = l2clk (L2 Cache clock derived from CPU0 clock)
+ 3 = ddrclk (DDR controller clock derived from CPU0 clock)
+
+The following is a list of provided IDs and clock names on 370/XP:
+ 0 = tclk (Internal Bus clock)
+ 1 = cpuclk (CPU clock)
+ 2 = nbclk (L2 Cache clock)
+ 3 = hclk (DRAM control clock)
+ 4 = dramclk (DDR clock)
+
+Required properties:
+- compatible : shall be one of the following:
+ "marvell,dove-core-clocks" - for Dove SoC core clocks
+ "marvell,kirkwood-core-clocks" - for Kirkwood SoC (except mv88f6180)
+ "marvell,mv88f6180-core-clocks" - for Kirkwood MV88f6180 SoC
+ "marvell,370-core-clocks" - For 370 SoC core clocks
+ "marvell,xp-core-clocks" - For XP SoC core clocks
+- reg : shall be the register address of the Sample-At-Reset (SAR) register
+- #clock-cells : from common clock binding; shall be set to 1
+
+Optional properties:
+- clock-output-names : from common clock binding; allows overwrite default clock
+ output names ("tclk", "cpuclk", "l2clk", "ddrclk")
+
+Example:
+
+core_clk: core-clocks at d0214 {
+ compatible = "marvell,dove-core-clocks";
+ reg = <0xd0214 0x4>;
+ #clock-cells = <1>;
+};
+
+spi0: spi at 10600 {
+ compatible = "marvell,orion-spi";
+ /* ... */
+ /* get tclk from core clock provider */
+ clocks = <&core_clk 0>;
+};
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index bace9e9..60427c0 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -54,3 +54,5 @@ config COMMON_CLK_MAX77686
This driver supports Maxim 77686 crystal oscillator clock.
endmenu
+
+source "drivers/clk/mvebu/Kconfig"
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 71a25b9..d0a14ae 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -13,6 +13,7 @@ obj-$(CONFIG_PLAT_SPEAR) += spear/
obj-$(CONFIG_ARCH_U300) += clk-u300.o
obj-$(CONFIG_COMMON_CLK_VERSATILE) += versatile/
obj-$(CONFIG_ARCH_PRIMA2) += clk-prima2.o
+obj-$(CONFIG_PLAT_ORION) += mvebu/
ifeq ($(CONFIG_COMMON_CLK), y)
obj-$(CONFIG_ARCH_MMP) += mmp/
endif
diff --git a/drivers/clk/mvebu/Kconfig b/drivers/clk/mvebu/Kconfig
new file mode 100644
index 0000000..fd7bf97
--- /dev/null
+++ b/drivers/clk/mvebu/Kconfig
@@ -0,0 +1,3 @@
+config MVEBU_CLK_CORE
+ bool
+
diff --git a/drivers/clk/mvebu/Makefile b/drivers/clk/mvebu/Makefile
new file mode 100644
index 0000000..de1d961
--- /dev/null
+++ b/drivers/clk/mvebu/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_MVEBU_CLK_CORE) += clk.o clk-core.o
diff --git a/drivers/clk/mvebu/clk-core.c b/drivers/clk/mvebu/clk-core.c
new file mode 100644
index 0000000..26ba835
--- /dev/null
+++ b/drivers/clk/mvebu/clk-core.c
@@ -0,0 +1,675 @@
+/*
+ * Marvell EBU clock core handling defined at reset
+ *
+ * Copyright (C) 2012 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement at free-electrons.com>
+ * Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/kernel.h>
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+#include <linux/of_address.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include "clk-core.h"
+
+struct core_ratio {
+ int id;
+ const char *name;
+};
+
+struct core_clocks {
+ u32 (*get_tclk_freq)(void __iomem *sar);
+ u32 (*get_cpu_freq)(void __iomem *sar);
+ void (*get_clk_ratio)(void __iomem *sar, int id, int *mult, int *div);
+ const struct core_ratio *ratios;
+ int num_ratios;
+};
+
+static struct clk_onecell_data clk_data;
+
+static void __init mvebu_clk_core_setup(struct device_node *np,
+ struct core_clocks *coreclk)
+{
+ const char *tclk_name = "tclk";
+ const char *cpuclk_name = "cpuclk";
+ void __iomem *base;
+ unsigned long rate;
+ int n;
+
+ base = of_iomap(np, 0);
+ if (WARN_ON(!base))
+ return;
+
+ /*
+ * Allocate struct for TCLK, cpu clk, and core ratio clocks
+ */
+ clk_data.clk_num = 2 + coreclk->num_ratios;
+ clk_data.clks = kzalloc(clk_data.clk_num * sizeof(struct clk *),
+ GFP_KERNEL);
+ if (WARN_ON(!clk_data.clks))
+ return;
+
+ /*
+ * Register TCLK
+ */
+ of_property_read_string_index(np, "clock-output-names", 0,
+ &tclk_name);
+ rate = coreclk->get_tclk_freq(base);
+ clk_data.clks[0] = clk_register_fixed_rate(NULL, tclk_name, NULL,
+ CLK_IS_ROOT, rate);
+ WARN_ON(IS_ERR(clk_data.clks[0]));
+
+ /*
+ * Register CPU clock
+ */
+ of_property_read_string_index(np, "clock-output-names", 1,
+ &cpuclk_name);
+ rate = coreclk->get_cpu_freq(base);
+ clk_data.clks[1] = clk_register_fixed_rate(NULL, cpuclk_name, NULL,
+ CLK_IS_ROOT, rate);
+ WARN_ON(IS_ERR(clk_data.clks[1]));
+
+ /*
+ * Register fixed-factor clocks derived from CPU clock
+ */
+ for (n = 0; n < coreclk->num_ratios; n++) {
+ const char *rclk_name = coreclk->ratios[n].name;
+ int mult, div;
+
+ of_property_read_string_index(np, "clock-output-names",
+ 2+n, &rclk_name);
+ coreclk->get_clk_ratio(base, coreclk->ratios[n].id,
+ &mult, &div);
+ clk_data.clks[2+n] = clk_register_fixed_factor(NULL, rclk_name,
+ cpuclk_name, 0, mult, div);
+ WARN_ON(IS_ERR(clk_data.clks[2+n]));
+ };
+
+ /*
+ * SAR register isn't needed anymore
+ */
+ iounmap(base);
+
+ of_clk_add_provider(np, of_clk_src_onecell_get, &clk_data);
+}
+
+#ifdef CONFIG_MACH_ARMADA_370_XP
+/*
+ * 370/XP Sample At Reset is a 64 bit bitfiled split in two register
+ * of 32 bits
+ */
+
+#define SARL 0 /* Low part [0:31] */
+#define SARL_AXP_PCLK_FREQ_OPT 21
+#define SARL_AXP_PCLK_FREQ_OPT_MASK 0x7
+#define SARL_A370_PCLK_FREQ_OPT 11
+#define SARL_A370_PCLK_FREQ_OPT_MASK 0xF
+#define SARL_AXP_FAB_FREQ_OPT 24
+#define SARL_AXP_FAB_FREQ_OPT_MASK 0xF
+#define SARL_A370_FAB_FREQ_OPT 15
+#define SARL_A370_FAB_FREQ_OPT_MASK 0x1F
+#define SARL_A370_TCLK_FREQ_OPT 20
+#define SARL_A370_TCLK_FREQ_OPT_MASK 0x1
+#define SARH 4 /* High part [32:63] */
+#define SARH_AXP_PCLK_FREQ_OPT (52-32)
+#define SARH_AXP_PCLK_FREQ_OPT_MASK 0x1
+#define SARH_AXP_PCLK_FREQ_OPT_SHIFT 3
+#define SARH_AXP_FAB_FREQ_OPT (51-32)
+#define SARH_AXP_FAB_FREQ_OPT_MASK 0x1
+#define SARH_AXP_FAB_FREQ_OPT_SHIFT 4
+
+static const u32 __initconst a370_tclk_frequencies[] = {
+ 16600000,
+ 20000000,
+};
+
+static u32 __init a370_get_tclk_freq(void __iomem *sar)
+{
+ u8 tclk_freq_select = 0;
+
+ tclk_freq_select = ((readl(sar) >> SARL_A370_TCLK_FREQ_OPT) &
+ SARL_A370_TCLK_FREQ_OPT_MASK);
+ return a370_tclk_frequencies[tclk_freq_select];
+}
+
+static const u32 __initconst a370_cpu_frequencies[] = {
+ 400000000,
+ 533000000,
+ 667000000,
+ 800000000,
+ 1000000000,
+ 1067000000,
+ 1200000000,
+};
+
+static u32 __init a370_get_cpu_freq(void __iomem *sar)
+{
+ u32 cpu_freq;
+ u8 cpu_freq_select = 0;
+
+ cpu_freq_select = ((readl(sar) >> SARL_A370_PCLK_FREQ_OPT) &
+ SARL_A370_PCLK_FREQ_OPT_MASK);
+ if (cpu_freq_select > ARRAY_SIZE(a370_cpu_frequencies)) {
+ pr_err("CPU freq select unsuported %d\n", cpu_freq_select);
+ cpu_freq = 0;
+ } else
+ cpu_freq = a370_cpu_frequencies[cpu_freq_select];
+
+ return cpu_freq;
+}
+
+enum { A370_XP_NBCLK, A370_XP_HCLK, A370_XP_DRAMCLK };
+
+static const struct core_ratio __initconst a370_xp_core_ratios[] = {
+ { .id = A370_XP_NBCLK, .name = "nbclk" },
+ { .id = A370_XP_HCLK, .name = "hclk" },
+ { .id = A370_XP_DRAMCLK, .name = "dramclk" },
+};
+
+static const int __initconst a370_xp_nbclk_ratios[32][2] = {
+ {0, 1}, {1, 2}, {2, 2}, {2, 2},
+ {1, 2}, {1, 2}, {1, 1}, {2, 3},
+ {0, 1}, {1, 2}, {2, 4}, {0, 1},
+ {1, 2}, {0, 1}, {0, 1}, {2, 2},
+ {0, 1}, {0, 1}, {0, 1}, {1, 1},
+ {2, 3}, {0, 1}, {0, 1}, {0, 1},
+ {0, 1}, {0, 1}, {0, 1}, {1, 1},
+ {0, 1}, {0, 1}, {0, 1}, {0, 1},
+};
+
+static const int __initconst a370_xp_hclk_ratios[32][2] = {
+ {0, 1}, {1, 2}, {2, 6}, {2, 3},
+ {1, 3}, {1, 4}, {1, 2}, {2, 6},
+ {0, 1}, {1, 6}, {2, 10}, {0, 1},
+ {1, 4}, {0, 1}, {0, 1}, {2, 5},
+ {0, 1}, {0, 1}, {0, 1}, {1, 2},
+ {2, 6}, {0, 1}, {0, 1}, {0, 1},
+ {0, 1}, {0, 1}, {0, 1}, {1, 1},
+ {0, 1}, {0, 1}, {0, 1}, {0, 1},
+};
+
+static const int __initconst a370_xp_dramclk_ratios[32][2] = {
+ {0, 1}, {1, 2}, {2, 3}, {2, 3},
+ {1, 3}, {1, 2}, {1, 2}, {2, 6},
+ {0, 1}, {1, 3}, {2, 5}, {0, 1},
+ {1, 4}, {0, 1}, {0, 1}, {2, 5},
+ {0, 1}, {0, 1}, {0, 1}, {1, 1},
+ {2, 3}, {0, 1}, {0, 1}, {0, 1},
+ {0, 1}, {0, 1}, {0, 1}, {1, 1},
+ {0, 1}, {0, 1}, {0, 1}, {0, 1},
+};
+
+static void __init a370_xp_get_clk_ratio(u32 opt,
+ void __iomem *sar, int id, int *mult, int *div)
+{
+ switch (id) {
+ case A370_XP_NBCLK:
+ *mult = a370_xp_nbclk_ratios[opt][0];
+ *div = a370_xp_nbclk_ratios[opt][1];
+ break;
+ case A370_XP_HCLK:
+ *mult = a370_xp_hclk_ratios[opt][0];
+ *div = a370_xp_hclk_ratios[opt][1];
+ break;
+ case A370_XP_DRAMCLK:
+ *mult = a370_xp_dramclk_ratios[opt][0];
+ *div = a370_xp_dramclk_ratios[opt][1];
+ break;
+ }
+}
+
+static void __init a370_get_clk_ratio(
+ void __iomem *sar, int id, int *mult, int *div)
+{
+ u32 opt = ((readl(sar) >> SARL_A370_FAB_FREQ_OPT) &
+ SARL_A370_FAB_FREQ_OPT_MASK);
+
+ a370_xp_get_clk_ratio(opt, sar, id, mult, div);
+}
+
+
+static const struct core_clocks a370_core_clocks = {
+ .get_tclk_freq = a370_get_tclk_freq,
+ .get_cpu_freq = a370_get_cpu_freq,
+ .get_clk_ratio = a370_get_clk_ratio,
+ .ratios = a370_xp_core_ratios,
+ .num_ratios = ARRAY_SIZE(a370_xp_core_ratios),
+};
+
+static const u32 __initconst xp_cpu_frequencies[] = {
+ 1000000000,
+ 1066000000,
+ 1200000000,
+ 1333000000,
+ 1500000000,
+ 1666000000,
+ 1800000000,
+ 2000000000,
+ 667000000,
+ 0,
+ 800000000,
+ 1600000000,
+};
+
+/* For Armada XP TCLK frequency is fix: 250MHz */
+static u32 __init xp_get_tclk_freq(void __iomem *sar)
+{
+ return 250 * 1000 * 1000;
+}
+
+static u32 __init xp_get_cpu_freq(void __iomem *sar)
+{
+ u32 cpu_freq;
+ u8 cpu_freq_select = 0;
+
+ cpu_freq_select = ((readl(sar) >> SARL_AXP_PCLK_FREQ_OPT) &
+ SARL_AXP_PCLK_FREQ_OPT_MASK);
+ /*
+ * The upper bit is not contiguous to the other ones and
+ * located in the high part of the SAR registers
+ */
+ cpu_freq_select |= (((readl(sar+4) >> SARH_AXP_PCLK_FREQ_OPT) &
+ SARH_AXP_PCLK_FREQ_OPT_MASK)
+ << SARH_AXP_PCLK_FREQ_OPT_SHIFT);
+ if (cpu_freq_select > ARRAY_SIZE(xp_cpu_frequencies)) {
+ pr_err("CPU freq select unsuported: %d\n", cpu_freq_select);
+ cpu_freq = 0;
+ } else
+ cpu_freq = xp_cpu_frequencies[cpu_freq_select];
+
+ return cpu_freq;
+}
+
+static void __init xp_get_clk_ratio(
+ void __iomem *sar, int id, int *mult, int *div)
+{
+
+ u32 opt = ((readl(sar) >> SARL_AXP_FAB_FREQ_OPT) &
+ SARL_AXP_FAB_FREQ_OPT_MASK);
+ /*
+ * The upper bit is not contiguous to the other ones and
+ * located in the high part of the SAR registers
+ */
+ opt |= (((readl(sar+4) >> SARH_AXP_FAB_FREQ_OPT) &
+ SARH_AXP_FAB_FREQ_OPT_MASK)
+ << SARH_AXP_FAB_FREQ_OPT_SHIFT);
+
+ a370_xp_get_clk_ratio(opt, sar, id, mult, div);
+}
+
+static const struct core_clocks xp_core_clocks = {
+ .get_tclk_freq = xp_get_tclk_freq,
+ .get_cpu_freq = xp_get_cpu_freq,
+ .get_clk_ratio = xp_get_clk_ratio,
+ .ratios = a370_xp_core_ratios,
+ .num_ratios = ARRAY_SIZE(a370_xp_core_ratios),
+};
+
+#endif /* CONFIG_MACH_ARMADA_370_XP */
+
+/*
+ * Dove PLL sample-at-reset configuration
+ *
+ * SAR0[8:5] : CPU frequency
+ * 5 = 1000 MHz
+ * 6 = 933 MHz
+ * 7 = 933 MHz
+ * 8 = 800 MHz
+ * 9 = 800 MHz
+ * 10 = 800 MHz
+ * 11 = 1067 MHz
+ * 12 = 667 MHz
+ * 13 = 533 MHz
+ * 14 = 400 MHz
+ * 15 = 333 MHz
+ * others reserved.
+ *
+ * SAR0[11:9] : CPU to L2 Clock divider ratio
+ * 0 = (1/1) * CPU
+ * 2 = (1/2) * CPU
+ * 4 = (1/3) * CPU
+ * 6 = (1/4) * CPU
+ * others reserved.
+ *
+ * SAR0[15:12] : CPU to DDR DRAM Clock divider ratio
+ * 0 = (1/1) * CPU
+ * 2 = (1/2) * CPU
+ * 3 = (2/5) * CPU
+ * 4 = (1/3) * CPU
+ * 6 = (1/4) * CPU
+ * 8 = (1/5) * CPU
+ * 10 = (1/6) * CPU
+ * 12 = (1/7) * CPU
+ * 14 = (1/8) * CPU
+ * 15 = (1/10) * CPU
+ * others reserved.
+ *
+ * SAR0[24:23] : TCLK frequency
+ * 0 = 166 MHz
+ * 1 = 125 MHz
+ * others reserved.
+ */
+#ifdef CONFIG_ARCH_DOVE
+#define SAR_DOVE_CPU_FREQ 5
+#define SAR_DOVE_CPU_FREQ_MASK 0xf
+#define SAR_DOVE_L2_RATIO 9
+#define SAR_DOVE_L2_RATIO_MASK 0x7
+#define SAR_DOVE_DDR_RATIO 12
+#define SAR_DOVE_DDR_RATIO_MASK 0xf
+#define SAR_DOVE_TCLK_FREQ 23
+#define SAR_DOVE_TCLK_FREQ_MASK 0x3
+
+static const u32 __initconst dove_tclk_frequencies[] = {
+ 166666667,
+ 125000000,
+ 0, 0
+};
+
+static u32 __init dove_get_tclk_freq(void __iomem *sar)
+{
+ u32 opt = (readl(sar) >> SAR_DOVE_TCLK_FREQ) &
+ SAR_DOVE_TCLK_FREQ_MASK;
+ return dove_tclk_frequencies[opt];
+}
+
+static const u32 __initconst dove_cpu_frequencies[] = {
+ 0, 0, 0, 0, 0,
+ 1000000000,
+ 933333333, 933333333,
+ 800000000, 800000000, 800000000,
+ 1066666667,
+ 666666667,
+ 533333333,
+ 400000000,
+ 333333333
+};
+
+static u32 __init dove_get_cpu_freq(void __iomem *sar)
+{
+ u32 opt = (readl(sar) >> SAR_DOVE_CPU_FREQ) &
+ SAR_DOVE_CPU_FREQ_MASK;
+ return dove_cpu_frequencies[opt];
+}
+
+enum { DOVE_CPU_TO_L2, DOVE_CPU_TO_DDR };
+
+static const struct core_ratio __initconst dove_core_ratios[] = {
+ { .id = DOVE_CPU_TO_L2, .name = "l2clk", },
+ { .id = DOVE_CPU_TO_DDR, .name = "ddrclk", }
+};
+
+static const int __initconst dove_cpu_l2_ratios[8][2] = {
+ { 1, 1 }, { 0, 1 }, { 1, 2 }, { 0, 1 },
+ { 1, 3 }, { 0, 1 }, { 1, 4 }, { 0, 1 }
+};
+
+static const int __initconst dove_cpu_ddr_ratios[16][2] = {
+ { 1, 1 }, { 0, 1 }, { 1, 2 }, { 2, 5 },
+ { 1, 3 }, { 0, 1 }, { 1, 4 }, { 0, 1 },
+ { 1, 5 }, { 0, 1 }, { 1, 6 }, { 0, 1 },
+ { 1, 7 }, { 0, 1 }, { 1, 8 }, { 1, 10 }
+};
+
+static void __init dove_get_clk_ratio(
+ void __iomem *sar, int id, int *mult, int *div)
+{
+ switch (id) {
+ case DOVE_CPU_TO_L2:
+ {
+ u32 opt = (readl(sar) >> SAR_DOVE_L2_RATIO) &
+ SAR_DOVE_L2_RATIO_MASK;
+ *mult = dove_cpu_l2_ratios[opt][0];
+ *div = dove_cpu_l2_ratios[opt][1];
+ break;
+ }
+ case DOVE_CPU_TO_DDR:
+ {
+ u32 opt = (readl(sar) >> SAR_DOVE_DDR_RATIO) &
+ SAR_DOVE_DDR_RATIO_MASK;
+ *mult = dove_cpu_ddr_ratios[opt][0];
+ *div = dove_cpu_ddr_ratios[opt][1];
+ break;
+ }
+ }
+}
+
+static const struct core_clocks dove_core_clocks = {
+ .get_tclk_freq = dove_get_tclk_freq,
+ .get_cpu_freq = dove_get_cpu_freq,
+ .get_clk_ratio = dove_get_clk_ratio,
+ .ratios = dove_core_ratios,
+ .num_ratios = ARRAY_SIZE(dove_core_ratios),
+};
+#endif /* CONFIG_ARCH_DOVE */
+
+/*
+ * Kirkwood PLL sample-at-reset configuration
+ * (6180 has different SAR layout than other Kirkwood SoCs)
+ *
+ * SAR0[4:3,22,1] : CPU frequency (6281,6292,6282)
+ * 4 = 600 MHz
+ * 6 = 800 MHz
+ * 7 = 1000 MHz
+ * 9 = 1200 MHz
+ * 12 = 1500 MHz
+ * 13 = 1600 MHz
+ * 14 = 1800 MHz
+ * 15 = 2000 MHz
+ * others reserved.
+ *
+ * SAR0[19,10:9] : CPU to L2 Clock divider ratio (6281,6292,6282)
+ * 1 = (1/2) * CPU
+ * 3 = (1/3) * CPU
+ * 5 = (1/4) * CPU
+ * others reserved.
+ *
+ * SAR0[8:5] : CPU to DDR DRAM Clock divider ratio (6281,6292,6282)
+ * 2 = (1/2) * CPU
+ * 4 = (1/3) * CPU
+ * 6 = (1/4) * CPU
+ * 7 = (2/9) * CPU
+ * 8 = (1/5) * CPU
+ * 9 = (1/6) * CPU
+ * others reserved.
+ *
+ * SAR0[4:2] : Kirkwood 6180 cpu/l2/ddr clock configuration (6180 only)
+ * 5 = [CPU = 600 MHz, L2 = (1/2) * CPU, DDR = 200 MHz = (1/3) * CPU]
+ * 6 = [CPU = 800 MHz, L2 = (1/2) * CPU, DDR = 200 MHz = (1/4) * CPU]
+ * 7 = [CPU = 1000 MHz, L2 = (1/2) * CPU, DDR = 200 MHz = (1/5) * CPU]
+ * others reserved.
+ *
+ * SAR0[21] : TCLK frequency
+ * 0 = 200 MHz
+ * 1 = 166 MHz
+ * others reserved.
+ */
+#ifdef CONFIG_ARCH_KIRKWOOD
+#define SAR_KIRKWOOD_CPU_FREQ(x) \
+ (((x & (1 << 1)) >> 1) | \
+ ((x & (1 << 22)) >> 21) | \
+ ((x & (3 << 3)) >> 1))
+#define SAR_KIRKWOOD_L2_RATIO(x) \
+ (((x & (3 << 9)) >> 9) | \
+ (((x & (1 << 19)) >> 17)))
+#define SAR_KIRKWOOD_DDR_RATIO 5
+#define SAR_KIRKWOOD_DDR_RATIO_MASK 0xf
+#define SAR_MV88F6180_CLK 2
+#define SAR_MV88F6180_CLK_MASK 0x7
+#define SAR_KIRKWOOD_TCLK_FREQ 21
+#define SAR_KIRKWOOD_TCLK_FREQ_MASK 0x1
+
+enum { KIRKWOOD_CPU_TO_L2, KIRKWOOD_CPU_TO_DDR };
+
+static const struct core_ratio __initconst kirkwood_core_ratios[] = {
+ { .id = KIRKWOOD_CPU_TO_L2, .name = "l2clk", },
+ { .id = KIRKWOOD_CPU_TO_DDR, .name = "ddrclk", }
+};
+
+static u32 __init kirkwood_get_tclk_freq(void __iomem *sar)
+{
+ u32 opt = (readl(sar) >> SAR_KIRKWOOD_TCLK_FREQ) &
+ SAR_KIRKWOOD_TCLK_FREQ_MASK;
+ return (opt) ? 166666667 : 200000000;
+}
+
+static const u32 __initconst kirkwood_cpu_frequencies[] = {
+ 0, 0, 0, 0,
+ 600000000,
+ 0,
+ 800000000,
+ 1000000000,
+ 0,
+ 1200000000,
+ 0, 0,
+ 1500000000,
+ 1600000000,
+ 1800000000,
+ 2000000000
+};
+
+static u32 __init kirkwood_get_cpu_freq(void __iomem *sar)
+{
+ u32 opt = SAR_KIRKWOOD_CPU_FREQ(readl(sar));
+ return kirkwood_cpu_frequencies[opt];
+}
+
+static const int __initconst kirkwood_cpu_l2_ratios[8][2] = {
+ { 0, 1 }, { 1, 2 }, { 0, 1 }, { 1, 3 },
+ { 0, 1 }, { 1, 4 }, { 0, 1 }, { 0, 1 }
+};
+
+static const int __initconst kirkwood_cpu_ddr_ratios[16][2] = {
+ { 0, 1 }, { 0, 1 }, { 1, 2 }, { 0, 1 },
+ { 1, 3 }, { 0, 1 }, { 1, 4 }, { 2, 9 },
+ { 1, 5 }, { 1, 6 }, { 0, 1 }, { 0, 1 },
+ { 0, 1 }, { 0, 1 }, { 0, 1 }, { 0, 1 }
+};
+
+static void __init kirkwood_get_clk_ratio(
+ void __iomem *sar, int id, int *mult, int *div)
+{
+ switch (id) {
+ case KIRKWOOD_CPU_TO_L2:
+ {
+ u32 opt = SAR_KIRKWOOD_L2_RATIO(readl(sar));
+ *mult = kirkwood_cpu_l2_ratios[opt][0];
+ *div = kirkwood_cpu_l2_ratios[opt][1];
+ break;
+ }
+ case KIRKWOOD_CPU_TO_DDR:
+ {
+ u32 opt = (readl(sar) >> SAR_KIRKWOOD_DDR_RATIO) &
+ SAR_KIRKWOOD_DDR_RATIO_MASK;
+ *mult = kirkwood_cpu_ddr_ratios[opt][0];
+ *div = kirkwood_cpu_ddr_ratios[opt][1];
+ break;
+ }
+ }
+}
+
+static const struct core_clocks kirkwood_core_clocks = {
+ .get_tclk_freq = kirkwood_get_tclk_freq,
+ .get_cpu_freq = kirkwood_get_cpu_freq,
+ .get_clk_ratio = kirkwood_get_clk_ratio,
+ .ratios = kirkwood_core_ratios,
+ .num_ratios = ARRAY_SIZE(kirkwood_core_ratios),
+};
+
+static const u32 __initconst mv88f6180_cpu_frequencies[] = {
+ 0, 0, 0, 0, 0,
+ 600000000,
+ 800000000,
+ 1000000000
+};
+
+static u32 __init mv88f6180_get_cpu_freq(void __iomem *sar)
+{
+ u32 opt = (readl(sar) >> SAR_MV88F6180_CLK) & SAR_MV88F6180_CLK_MASK;
+ return mv88f6180_cpu_frequencies[opt];
+}
+
+static const int __initconst mv88f6180_cpu_ddr_ratios[8][2] = {
+ { 0, 1 }, { 0, 1 }, { 0, 1 }, { 0, 1 },
+ { 0, 1 }, { 1, 3 }, { 1, 4 }, { 1, 5 }
+};
+
+static void __init mv88f6180_get_clk_ratio(
+ void __iomem *sar, int id, int *mult, int *div)
+{
+ switch (id) {
+ case KIRKWOOD_CPU_TO_L2:
+ {
+ /* mv88f6180 has a fixed 1:2 CPU-to-L2 ratio */
+ *mult = 1;
+ *div = 2;
+ break;
+ }
+ case KIRKWOOD_CPU_TO_DDR:
+ {
+ u32 opt = (readl(sar) >> SAR_MV88F6180_CLK) &
+ SAR_MV88F6180_CLK_MASK;
+ *mult = mv88f6180_cpu_ddr_ratios[opt][0];
+ *div = mv88f6180_cpu_ddr_ratios[opt][1];
+ break;
+ }
+ }
+}
+
+static const struct core_clocks mv88f6180_core_clocks = {
+ .get_tclk_freq = kirkwood_get_tclk_freq,
+ .get_cpu_freq = mv88f6180_get_cpu_freq,
+ .get_clk_ratio = mv88f6180_get_clk_ratio,
+ .ratios = kirkwood_core_ratios,
+ .num_ratios = ARRAY_SIZE(kirkwood_core_ratios),
+};
+#endif /* CONFIG_ARCH_KIRKWOOD */
+
+static const __initdata struct of_device_id clk_core_match[] = {
+#ifdef CONFIG_MACH_ARMADA_370_XP
+ {
+ .compatible = "marvell,370-core-clocks",
+ .data = &a370_core_clocks,
+ },
+ {
+ .compatible = "marvell,xp-core-clocks",
+ .data = &xp_core_clocks,
+ },
+#endif
+#ifdef CONFIG_ARCH_DOVE
+ {
+ .compatible = "marvell,dove-core-clocks",
+ .data = &dove_core_clocks,
+ },
+#endif
+
+#ifdef CONFIG_ARCH_KIRKWOOD
+ {
+ .compatible = "marvell,kirkwood-core-clocks",
+ .data = &kirkwood_core_clocks,
+ },
+ {
+ .compatible = "marvell,mv88f6180-core-clocks",
+ .data = &mv88f6180_core_clocks,
+ },
+#endif
+
+ { }
+};
+
+void __init mvebu_core_clk_init(void)
+{
+ struct device_node *np;
+
+ for_each_matching_node(np, clk_core_match) {
+ const struct of_device_id *match =
+ of_match_node(clk_core_match, np);
+ mvebu_clk_core_setup(np, (struct core_clocks *)match->data);
+ }
+}
diff --git a/drivers/clk/mvebu/clk-core.h b/drivers/clk/mvebu/clk-core.h
new file mode 100644
index 0000000..28b5e02
--- /dev/null
+++ b/drivers/clk/mvebu/clk-core.h
@@ -0,0 +1,18 @@
+/*
+ * * Marvell EBU clock core handling defined at reset
+ *
+ * Copyright (C) 2012 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement at free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __MVEBU_CLK_CORE_H
+#define __MVEBU_CLK_CORE_H
+
+void __init mvebu_core_clk_init(void);
+
+#endif
diff --git a/drivers/clk/mvebu/clk.c b/drivers/clk/mvebu/clk.c
new file mode 100644
index 0000000..e6742ac
--- /dev/null
+++ b/drivers/clk/mvebu/clk.c
@@ -0,0 +1,23 @@
+/*
+ * Marvell EBU SoC clock handling.
+ *
+ * Copyright (C) 2012 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement at free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/kernel.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/of_address.h>
+#include <linux/clk/mvebu.h>
+#include <linux/of.h>
+#include "clk-core.h"
+
+void __init mvebu_clocks_init(void)
+{
+ mvebu_core_clk_init();
+}
diff --git a/include/linux/clk/mvebu.h b/include/linux/clk/mvebu.h
new file mode 100644
index 0000000..8c4ae71
--- /dev/null
+++ b/include/linux/clk/mvebu.h
@@ -0,0 +1,22 @@
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __CLK_MVEBU_H_
+#define __CLK_MVEBU_H_
+
+void __init mvebu_clocks_init(void);
+
+#endif
--
1.7.10.4
More information about the devicetree-discuss
mailing list