[PATCH V2 04/14] OF: pinctrl: MIPS: lantiq: implement lantiq/xway pinctrl support
John Crispin
blogic at openwrt.org
Thu May 10 22:27:26 EST 2012
Implement support for pinctrl on lantiq/xway socs. The IO core found on these
socs has the registers for pinctrl, pinconf and gpio mixed up in the same
register range. As the gpio_chip handling is only a few lines, the driver also
implements the gpio functionality. This obseletes the old gpio driver that was
located in the arch/ folder.
Signed-off-by: John Crispin <blogic at openwrt.org>
Cc: devicetree-discuss at lists.ozlabs.org
Cc: Linus Walleij <linus.walleij at linaro.org>
Cc: Stephen Warren <swarren at wwwdotorg.org>
---
This patch is part of a series moving the mips/lantiq target to OF and clkdev
support. The patch, once Acked, should go upstream via Ralf's MIPS tree.
Changes in V2
* cleanup select/depends of the relevant Kconfig symbols
* dont assume that the arry with out MFPs is linearly mapped
* sane return code checks inside ltq_pinctrl_dt_node_to_map
* remove 2 calls to pr_err and replace them with calls to dev_err
* propagate gpio_chips base addr to the gpio_range
* define the pin count inside the of_device_id.data
* minor changes to accomodate the pinctrl-falcon driver (more virt pointers
and clocks)
* change from core_initcall_sync to arch_initcall
* several typos, codestyle and whitespace cleanups
* use BIT(x) in favour of (1 << x)
arch/mips/Kconfig | 2 +
.../mips/include/asm/mach-lantiq/xway/lantiq_soc.h | 2 -
arch/mips/lantiq/Kconfig | 2 +
arch/mips/lantiq/xway/Makefile | 2 +-
arch/mips/lantiq/xway/gpio.c | 195 ------
arch/mips/lantiq/xway/gpio_stp.c | 5 -
arch/mips/pci/pci-lantiq.c | 44 +--
drivers/pinctrl/Kconfig | 11 +
drivers/pinctrl/Makefile | 2 +
drivers/pinctrl/pinctrl-lantiq.c | 342 ++++++++++
drivers/pinctrl/pinctrl-lantiq.h | 190 ++++++
drivers/pinctrl/pinctrl-xway.c | 652 ++++++++++++++++++++
12 files changed, 1203 insertions(+), 246 deletions(-)
delete mode 100644 arch/mips/lantiq/xway/gpio.c
create mode 100644 drivers/pinctrl/pinctrl-lantiq.c
create mode 100644 drivers/pinctrl/pinctrl-lantiq.h
create mode 100644 drivers/pinctrl/pinctrl-xway.c
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index fbb5639..200e920 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -229,6 +229,8 @@ config LANTIQ
select SWAP_IO_SPACE
select BOOT_RAW
select HAVE_CLK
+ select PINCTRL
+ select PINCTRL_LANTIQ
select USE_OF
config LASAT
diff --git a/arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h b/arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h
index 15eb4dc..150c7be 100644
--- a/arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h
+++ b/arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h
@@ -153,8 +153,6 @@
#define LTQ_MPS_CHIPID ((u32 *)(LTQ_MPS_BASE_ADDR + 0x0344))
/* request a non-gpio and set the PIO config */
-extern int ltq_gpio_request(unsigned int pin, unsigned int alt0,
- unsigned int alt1, unsigned int dir, const char *name);
extern void ltq_pmu_enable(unsigned int module);
extern void ltq_pmu_disable(unsigned int module);
diff --git a/arch/mips/lantiq/Kconfig b/arch/mips/lantiq/Kconfig
index 9485fe5..60d0f64 100644
--- a/arch/mips/lantiq/Kconfig
+++ b/arch/mips/lantiq/Kconfig
@@ -2,6 +2,7 @@ if LANTIQ
config SOC_TYPE_XWAY
bool
+ select PINCTRL_XWAY
default n
choice
@@ -16,6 +17,7 @@ config SOC_XWAY
bool "XWAY"
select SOC_TYPE_XWAY
select HW_HAS_PCI
+
endchoice
diff --git a/arch/mips/lantiq/xway/Makefile b/arch/mips/lantiq/xway/Makefile
index 7a6c30f..323b574 100644
--- a/arch/mips/lantiq/xway/Makefile
+++ b/arch/mips/lantiq/xway/Makefile
@@ -1,4 +1,4 @@
-obj-y := prom.o pmu.o ebu.o reset.o gpio.o gpio_stp.o gpio_ebu.o dma.o
+obj-y := prom.o pmu.o ebu.o reset.o gpio_stp.o gpio_ebu.o dma.o
obj-$(CONFIG_SOC_XWAY) += clk-xway.o
obj-$(CONFIG_SOC_AMAZON_SE) += clk-ase.o
diff --git a/arch/mips/lantiq/xway/gpio.c b/arch/mips/lantiq/xway/gpio.c
deleted file mode 100644
index c429a5b..0000000
--- a/arch/mips/lantiq/xway/gpio.c
+++ /dev/null
@@ -1,195 +0,0 @@
-/*
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation.
- *
- * Copyright (C) 2010 John Crispin <blogic at openwrt.org>
- */
-
-#include <linux/slab.h>
-#include <linux/export.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-
-#include <lantiq_soc.h>
-
-#define LTQ_GPIO_OUT 0x00
-#define LTQ_GPIO_IN 0x04
-#define LTQ_GPIO_DIR 0x08
-#define LTQ_GPIO_ALTSEL0 0x0C
-#define LTQ_GPIO_ALTSEL1 0x10
-#define LTQ_GPIO_OD 0x14
-
-#define PINS_PER_PORT 16
-#define MAX_PORTS 3
-
-#define ltq_gpio_getbit(m, r, p) (!!(ltq_r32(m + r) & (1 << p)))
-#define ltq_gpio_setbit(m, r, p) ltq_w32_mask(0, (1 << p), m + r)
-#define ltq_gpio_clearbit(m, r, p) ltq_w32_mask((1 << p), 0, m + r)
-
-struct ltq_gpio {
- void __iomem *membase;
- struct gpio_chip chip;
-};
-
-static struct ltq_gpio ltq_gpio_port[MAX_PORTS];
-
-int gpio_to_irq(unsigned int gpio)
-{
- return -EINVAL;
-}
-EXPORT_SYMBOL(gpio_to_irq);
-
-int irq_to_gpio(unsigned int gpio)
-{
- return -EINVAL;
-}
-EXPORT_SYMBOL(irq_to_gpio);
-
-int ltq_gpio_request(unsigned int pin, unsigned int alt0,
- unsigned int alt1, unsigned int dir, const char *name)
-{
- int id = 0;
-
- if (pin >= (MAX_PORTS * PINS_PER_PORT))
- return -EINVAL;
- if (gpio_request(pin, name)) {
- pr_err("failed to setup lantiq gpio: %s\n", name);
- return -EBUSY;
- }
- if (dir)
- gpio_direction_output(pin, 1);
- else
- gpio_direction_input(pin);
- while (pin >= PINS_PER_PORT) {
- pin -= PINS_PER_PORT;
- id++;
- }
- if (alt0)
- ltq_gpio_setbit(ltq_gpio_port[id].membase,
- LTQ_GPIO_ALTSEL0, pin);
- else
- ltq_gpio_clearbit(ltq_gpio_port[id].membase,
- LTQ_GPIO_ALTSEL0, pin);
- if (alt1)
- ltq_gpio_setbit(ltq_gpio_port[id].membase,
- LTQ_GPIO_ALTSEL1, pin);
- else
- ltq_gpio_clearbit(ltq_gpio_port[id].membase,
- LTQ_GPIO_ALTSEL1, pin);
- return 0;
-}
-EXPORT_SYMBOL(ltq_gpio_request);
-
-static void ltq_gpio_set(struct gpio_chip *chip, unsigned int offset, int value)
-{
- struct ltq_gpio *ltq_gpio = container_of(chip, struct ltq_gpio, chip);
-
- if (value)
- ltq_gpio_setbit(ltq_gpio->membase, LTQ_GPIO_OUT, offset);
- else
- ltq_gpio_clearbit(ltq_gpio->membase, LTQ_GPIO_OUT, offset);
-}
-
-static int ltq_gpio_get(struct gpio_chip *chip, unsigned int offset)
-{
- struct ltq_gpio *ltq_gpio = container_of(chip, struct ltq_gpio, chip);
-
- return ltq_gpio_getbit(ltq_gpio->membase, LTQ_GPIO_IN, offset);
-}
-
-static int ltq_gpio_direction_input(struct gpio_chip *chip, unsigned int offset)
-{
- struct ltq_gpio *ltq_gpio = container_of(chip, struct ltq_gpio, chip);
-
- ltq_gpio_clearbit(ltq_gpio->membase, LTQ_GPIO_OD, offset);
- ltq_gpio_clearbit(ltq_gpio->membase, LTQ_GPIO_DIR, offset);
-
- return 0;
-}
-
-static int ltq_gpio_direction_output(struct gpio_chip *chip,
- unsigned int offset, int value)
-{
- struct ltq_gpio *ltq_gpio = container_of(chip, struct ltq_gpio, chip);
-
- ltq_gpio_setbit(ltq_gpio->membase, LTQ_GPIO_OD, offset);
- ltq_gpio_setbit(ltq_gpio->membase, LTQ_GPIO_DIR, offset);
- ltq_gpio_set(chip, offset, value);
-
- return 0;
-}
-
-static int ltq_gpio_req(struct gpio_chip *chip, unsigned offset)
-{
- struct ltq_gpio *ltq_gpio = container_of(chip, struct ltq_gpio, chip);
-
- ltq_gpio_clearbit(ltq_gpio->membase, LTQ_GPIO_ALTSEL0, offset);
- ltq_gpio_clearbit(ltq_gpio->membase, LTQ_GPIO_ALTSEL1, offset);
- return 0;
-}
-
-static int ltq_gpio_probe(struct platform_device *pdev)
-{
- struct resource *res;
-
- if (pdev->id >= MAX_PORTS) {
- dev_err(&pdev->dev, "invalid gpio port %d\n",
- pdev->id);
- return -EINVAL;
- }
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res) {
- dev_err(&pdev->dev, "failed to get memory for gpio port %d\n",
- pdev->id);
- return -ENOENT;
- }
- res = devm_request_mem_region(&pdev->dev, res->start,
- resource_size(res), dev_name(&pdev->dev));
- if (!res) {
- dev_err(&pdev->dev,
- "failed to request memory for gpio port %d\n",
- pdev->id);
- return -EBUSY;
- }
- ltq_gpio_port[pdev->id].membase = devm_ioremap_nocache(&pdev->dev,
- res->start, resource_size(res));
- if (!ltq_gpio_port[pdev->id].membase) {
- dev_err(&pdev->dev, "failed to remap memory for gpio port %d\n",
- pdev->id);
- return -ENOMEM;
- }
- ltq_gpio_port[pdev->id].chip.label = "ltq_gpio";
- ltq_gpio_port[pdev->id].chip.direction_input = ltq_gpio_direction_input;
- ltq_gpio_port[pdev->id].chip.direction_output =
- ltq_gpio_direction_output;
- ltq_gpio_port[pdev->id].chip.get = ltq_gpio_get;
- ltq_gpio_port[pdev->id].chip.set = ltq_gpio_set;
- ltq_gpio_port[pdev->id].chip.request = ltq_gpio_req;
- ltq_gpio_port[pdev->id].chip.base = PINS_PER_PORT * pdev->id;
- ltq_gpio_port[pdev->id].chip.ngpio = PINS_PER_PORT;
- platform_set_drvdata(pdev, <q_gpio_port[pdev->id]);
- return gpiochip_add(<q_gpio_port[pdev->id].chip);
-}
-
-static struct platform_driver
-ltq_gpio_driver = {
- .probe = ltq_gpio_probe,
- .driver = {
- .name = "ltq_gpio",
- .owner = THIS_MODULE,
- },
-};
-
-int __init ltq_gpio_init(void)
-{
- int ret = platform_driver_register(<q_gpio_driver);
-
- if (ret)
- pr_info("ltq_gpio : Error registering platform driver!");
- return ret;
-}
-
-postcore_initcall(ltq_gpio_init);
diff --git a/arch/mips/lantiq/xway/gpio_stp.c b/arch/mips/lantiq/xway/gpio_stp.c
index fd07d87..4f4bd61 100644
--- a/arch/mips/lantiq/xway/gpio_stp.c
+++ b/arch/mips/lantiq/xway/gpio_stp.c
@@ -78,11 +78,6 @@ static struct gpio_chip ltq_stp_chip = {
static int ltq_stp_hw_init(void)
{
- /* the 3 pins used to control the external stp */
- ltq_gpio_request(4, 1, 0, 1, "stp-st");
- ltq_gpio_request(5, 1, 0, 1, "stp-d");
- ltq_gpio_request(6, 1, 0, 1, "stp-sh");
-
/* sane defaults */
ltq_stp_w32(0, LTQ_STP_AR);
ltq_stp_w32(0, LTQ_STP_CPU0);
diff --git a/arch/mips/pci/pci-lantiq.c b/arch/mips/pci/pci-lantiq.c
index 70fdf2c..3418178 100644
--- a/arch/mips/pci/pci-lantiq.c
+++ b/arch/mips/pci/pci-lantiq.c
@@ -68,32 +68,6 @@
#define ltq_pci_cfg_w32(x, y) ltq_w32((x), ltq_pci_mapped_cfg + (y))
#define ltq_pci_cfg_r32(x) ltq_r32(ltq_pci_mapped_cfg + (x))
-struct ltq_pci_gpio_map {
- int pin;
- int alt0;
- int alt1;
- int dir;
- char *name;
-};
-
-/* the pci core can make use of the following gpios */
-static struct ltq_pci_gpio_map ltq_pci_gpio_map[] = {
- { 0, 1, 0, 0, "pci-exin0" },
- { 1, 1, 0, 0, "pci-exin1" },
- { 2, 1, 0, 0, "pci-exin2" },
- { 39, 1, 0, 0, "pci-exin3" },
- { 10, 1, 0, 0, "pci-exin4" },
- { 9, 1, 0, 0, "pci-exin5" },
- { 30, 1, 0, 1, "pci-gnt1" },
- { 23, 1, 0, 1, "pci-gnt2" },
- { 19, 1, 0, 1, "pci-gnt3" },
- { 38, 1, 0, 1, "pci-gnt4" },
- { 29, 1, 0, 0, "pci-req1" },
- { 31, 1, 0, 0, "pci-req2" },
- { 3, 1, 0, 0, "pci-req3" },
- { 37, 1, 0, 0, "pci-req4" },
-};
-
__iomem void *ltq_pci_mapped_cfg;
static __iomem void *ltq_pci_membase;
@@ -151,22 +125,6 @@ static u32 ltq_calc_bar11mask(void)
return bar11mask;
}
-static void ltq_pci_setup_gpio(int gpio)
-{
- int i;
- for (i = 0; i < ARRAY_SIZE(ltq_pci_gpio_map); i++) {
- if (gpio & (1 << i)) {
- ltq_gpio_request(ltq_pci_gpio_map[i].pin,
- ltq_pci_gpio_map[i].alt0,
- ltq_pci_gpio_map[i].alt1,
- ltq_pci_gpio_map[i].dir,
- ltq_pci_gpio_map[i].name);
- }
- }
- ltq_gpio_request(21, 0, 0, 1, "pci-reset");
- ltq_pci_req_mask = (gpio >> PCI_REQ_SHIFT) & PCI_REQ_MASK;
-}
-
static int __devinit ltq_pci_startup(struct ltq_pci_data *conf)
{
u32 temp_buffer;
@@ -192,7 +150,7 @@ static int __devinit ltq_pci_startup(struct ltq_pci_data *conf)
}
/* setup pci clock and gpis used by pci */
- ltq_pci_setup_gpio(conf->gpio);
+ gpio_request(21, "pci-reset");
/* enable auto-switching between PCI and EBU */
ltq_pci_w32(0xa, PCI_CR_CLK_CTRL);
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index f73a5ea..802ae9f 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -26,6 +26,12 @@ config DEBUG_PINCTRL
help
Say Y here to add some extra checks and diagnostics to PINCTRL calls.
+config PINCTRL_LANTIQ
+ bool
+ depends on LANTIQ
+ select PINMUX
+ select PINCONF
+
config PINCTRL_PXA3xx
bool
select PINMUX
@@ -83,6 +89,11 @@ config PINCTRL_COH901
COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
ports of 8 GPIO pins each.
+config PINCTRL_XWAY
+ bool
+ depends on SOC_TYPE_XWAY
+ depends on PINCTRL_LANTIQ
+
endmenu
endif
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index 8e3c95a..7896a12 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -9,6 +9,7 @@ ifeq ($(CONFIG_OF),y)
obj-$(CONFIG_PINCTRL) += devicetree.o
endif
obj-$(CONFIG_GENERIC_PINCONF) += pinconf-generic.o
+obj-$(CONFIG_PINCTRL_LANTIQ) += pinctrl-lantiq.o
obj-$(CONFIG_PINCTRL_PXA3xx) += pinctrl-pxa3xx.o
obj-$(CONFIG_PINCTRL_MMP2) += pinctrl-mmp2.o
obj-$(CONFIG_PINCTRL_PXA168) += pinctrl-pxa168.o
@@ -19,3 +20,4 @@ obj-$(CONFIG_PINCTRL_TEGRA20) += pinctrl-tegra20.o
obj-$(CONFIG_PINCTRL_TEGRA30) += pinctrl-tegra30.o
obj-$(CONFIG_PINCTRL_U300) += pinctrl-u300.o
obj-$(CONFIG_PINCTRL_COH901) += pinctrl-coh901.o
+obj-$(CONFIG_PINCTRL_XWAY) += pinctrl-xway.o
diff --git a/drivers/pinctrl/pinctrl-lantiq.c b/drivers/pinctrl/pinctrl-lantiq.c
new file mode 100644
index 0000000..07ba768
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-lantiq.c
@@ -0,0 +1,342 @@
+/*
+ * linux/drivers/pinctrl/pinctrl-lantiq.c
+ * based on linux/drivers/pinctrl/pinctrl-pxa3xx.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * publishhed by the Free Software Foundation.
+ *
+ * Copyright (C) 2012 John Crispin <blogic at openwrt.org>
+ */
+
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+
+#include "pinctrl-lantiq.h"
+
+static int ltq_get_group_count(struct pinctrl_dev *pctrldev)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctrldev);
+ return info->num_grps;
+}
+
+static const char *ltq_get_group_name(struct pinctrl_dev *pctrldev,
+ unsigned selector)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctrldev);
+ if (selector >= info->num_grps)
+ return NULL;
+ return info->grps[selector].name;
+}
+
+static int ltq_get_group_pins(struct pinctrl_dev *pctrldev,
+ unsigned selector,
+ const unsigned **pins,
+ unsigned *num_pins)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctrldev);
+ if (selector >= info->num_grps)
+ return -EINVAL;
+ *pins = info->grps[selector].pins;
+ *num_pins = info->grps[selector].npins;
+ return 0;
+}
+
+void ltq_pinctrl_dt_free_map(struct pinctrl_dev *pctldev,
+ struct pinctrl_map *map, unsigned num_maps)
+{
+ int i;
+
+ for (i = 0; i < num_maps; i++)
+ if (map[i].type == PIN_MAP_TYPE_CONFIGS_PIN)
+ kfree(map[i].data.configs.configs);
+ kfree(map);
+}
+
+static void ltq_pinctrl_pin_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s,
+ unsigned offset)
+{
+ seq_printf(s, " %s", dev_name(pctldev->dev));
+}
+
+static int ltq_pinctrl_dt_subnode_to_map(struct pinctrl_dev *pctldev,
+ struct device_node *np,
+ struct pinctrl_map **map)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctldev);
+ unsigned long configs[3];
+ unsigned num_configs = 0;
+ struct property *prop;
+ const char *group, *pin;
+ const char *function;
+ int ret, i;
+
+ ret = of_property_read_string(np, "lantiq,function", &function);
+ if (!ret) {
+ of_property_for_each_string(np, "lantiq,groups", prop, group) {
+ (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
+ (*map)->name = function;
+ (*map)->data.mux.group = group;
+ (*map)->data.mux.function = function;
+ (*map)++;
+ }
+ if (of_find_property(np, "lantiq,pins", NULL))
+ dev_err(pctldev->dev,
+ "%s mixes pins and groups settings\n",
+ np->name);
+ return 0;
+ }
+
+ for (i = 0; i < info->num_params; i++) {
+ u32 val;
+ int ret = of_property_read_u32(np,
+ info->params[i].property, &val);
+ if (!ret)
+ configs[num_configs++] =
+ LTQ_PINCONF_PACK(info->params[i].param,
+ val);
+ }
+
+ if (!num_configs)
+ return -EINVAL;
+
+ of_property_for_each_string(np, "lantiq,pins", prop, pin) {
+ (*map)->data.configs.configs = kmemdup(configs,
+ num_configs * sizeof(unsigned long),
+ GFP_KERNEL);
+ (*map)->type = PIN_MAP_TYPE_CONFIGS_PIN;
+ (*map)->name = pin;
+ (*map)->data.configs.group_or_pin = pin;
+ (*map)->data.configs.num_configs = num_configs;
+ (*map)++;
+ }
+ return 0;
+}
+
+static int ltq_pinctrl_dt_subnode_size(struct device_node *np)
+{
+ int ret;
+
+ ret = of_property_count_strings(np, "lantiq,groups");
+ if (ret < 0)
+ ret = of_property_count_strings(np, "lantiq,pins");
+ return ret;
+}
+
+int ltq_pinctrl_dt_node_to_map(struct pinctrl_dev *pctldev,
+ struct device_node *np_config,
+ struct pinctrl_map **map,
+ unsigned *num_maps)
+{
+ struct pinctrl_map *tmp;
+ struct device_node *np;
+ int ret;
+
+ *num_maps = 0;
+ for_each_child_of_node(np_config, np)
+ *num_maps += ltq_pinctrl_dt_subnode_size(np);
+ *map = kzalloc(*num_maps * sizeof(struct pinctrl_map), GFP_KERNEL);
+ if (!*map)
+ return -ENOMEM;
+ tmp = *map;
+
+ for_each_child_of_node(np_config, np) {
+ ret = ltq_pinctrl_dt_subnode_to_map(pctldev, np, &tmp);
+ if (ret < 0) {
+ ltq_pinctrl_dt_free_map(pctldev, *map, *num_maps);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+static struct pinctrl_ops ltq_pctrl_ops = {
+ .get_groups_count = ltq_get_group_count,
+ .get_group_name = ltq_get_group_name,
+ .get_group_pins = ltq_get_group_pins,
+ .pin_dbg_show = ltq_pinctrl_pin_dbg_show,
+ .dt_node_to_map = ltq_pinctrl_dt_node_to_map,
+ .dt_free_map = ltq_pinctrl_dt_free_map,
+};
+
+static int ltq_pmx_func_count(struct pinctrl_dev *pctrldev)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctrldev);
+
+ return info->num_funcs;
+}
+
+static const char *ltq_pmx_func_name(struct pinctrl_dev *pctrldev,
+ unsigned selector)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctrldev);
+
+ if (selector >= info->num_funcs)
+ return NULL;
+
+ return info->funcs[selector].name;
+}
+
+static int ltq_pmx_get_groups(struct pinctrl_dev *pctrldev,
+ unsigned func,
+ const char * const **groups,
+ unsigned * const num_groups)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctrldev);
+
+ *groups = info->funcs[func].groups;
+ *num_groups = info->funcs[func].num_groups;
+
+ return 0;
+}
+
+/* Return function number. If failure, return negative value. */
+static int match_mux(const struct ltq_mfp_pin *mfp, unsigned mux)
+{
+ int i;
+ for (i = 0; i < LTQ_MAX_MUX; i++) {
+ if (mfp->func[i] == mux)
+ break;
+ }
+ if (i >= LTQ_MAX_MUX)
+ return -EINVAL;
+ return i;
+}
+
+/* dont assume .mfp is linearly mapped. find the mfp with the correct .pin */
+static int match_mfp(const struct ltq_pinmux_info *info, int pin)
+{
+ int i;
+ for (i = 0; i < info->num_mfp; i++) {
+ if (info->mfp[i].pin == pin)
+ return i;
+ }
+ return -1;
+}
+
+/* check whether current pin configuration is valid. Negative for failure */
+static int match_group_mux(const struct ltq_pin_group *grp,
+ const struct ltq_pinmux_info *info,
+ unsigned mux)
+{
+ int i, pin, ret = 0;
+ for (i = 0; i < grp->npins; i++) {
+ pin = match_mfp(info, grp->pins[i]);
+ if (pin < 0) {
+ dev_err(info->dev, "could not find mfp for pin %d\n",
+ grp->pins[i]);
+ return -EINVAL;
+ }
+ ret = match_mux(&info->mfp[pin], mux);
+ if (ret < 0) {
+ dev_err(info->dev, "Can't find mux %d on pin%d\n",
+ mux, pin);
+ break;
+ }
+ }
+ return ret;
+}
+
+static int ltq_pmx_enable(struct pinctrl_dev *pctrldev,
+ unsigned func,
+ unsigned group)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctrldev);
+ const struct ltq_pin_group *pin_grp = &info->grps[group];
+ int i, pin, pin_func, ret;
+
+ if (!pin_grp->npins ||
+ (match_group_mux(pin_grp, info, pin_grp->mux) < 0)) {
+ dev_err(info->dev, "Failed to set the pin group: %s\n",
+ info->grps[group].name);
+ return -EINVAL;
+ }
+ for (i = 0; i < pin_grp->npins; i++) {
+ pin = match_mfp(info, pin_grp->pins[i]);
+ if (pin < 0) {
+ dev_err(info->dev, "could not find mfp for pin %d\n",
+ pin_grp->pins[i]);
+ return -EINVAL;
+ }
+ pin_func = match_mux(&info->mfp[pin], pin_grp->mux);
+ ret = info->apply_mux(pctrldev, pin, pin_func);
+ if (ret) {
+ dev_err(info->dev,
+ "failed to apply mux %d for pin %d\n",
+ pin_func, pin);
+ return ret;
+ }
+ }
+ return 0;
+}
+
+static void ltq_pmx_disable(struct pinctrl_dev *pctrldev,
+ unsigned func,
+ unsigned group)
+{
+ /*
+ * Nothing to do here. However, pinconf_check_ops() requires this
+ * callback to be defined.
+ */
+}
+
+static int ltq_pmx_gpio_request_enable(struct pinctrl_dev *pctrldev,
+ struct pinctrl_gpio_range *range,
+ unsigned pin)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctrldev);
+ int mfp = match_mfp(info, pin + (range->id * 32));
+ int pin_func;
+
+ if (mfp < 0) {
+ dev_err(info->dev, "could not find mfp for pin %d\n", pin);
+ return -EINVAL;
+ }
+
+ pin_func = match_mux(&info->mfp[mfp], 0);
+ if (pin_func < 0) {
+ dev_err(info->dev, "No GPIO function on pin%d\n", mfp);
+ return -EINVAL;
+ }
+
+ return info->apply_mux(pctrldev, mfp, pin_func);
+}
+
+static struct pinmux_ops ltq_pmx_ops = {
+ .get_functions_count = ltq_pmx_func_count,
+ .get_function_name = ltq_pmx_func_name,
+ .get_function_groups = ltq_pmx_get_groups,
+ .enable = ltq_pmx_enable,
+ .disable = ltq_pmx_disable,
+ .gpio_request_enable = ltq_pmx_gpio_request_enable,
+};
+
+/*
+ * allow different socs to register with the generic part of the lanti
+ * pinctrl code
+ */
+int ltq_pinctrl_register(struct platform_device *pdev,
+ struct ltq_pinmux_info *info)
+{
+ struct pinctrl_desc *desc;
+
+ if (!info)
+ return -EINVAL;
+ desc = info->desc;
+ desc->pctlops = <q_pctrl_ops;
+ desc->pmxops = <q_pmx_ops;
+ info->dev = &pdev->dev;
+
+ info->pctrl = pinctrl_register(desc, &pdev->dev, info);
+ if (!info->pctrl) {
+ dev_err(&pdev->dev, "failed to register LTQ pinmux driver\n");
+ return -EINVAL;
+ }
+ platform_set_drvdata(pdev, info);
+ return 0;
+}
diff --git a/drivers/pinctrl/pinctrl-lantiq.h b/drivers/pinctrl/pinctrl-lantiq.h
new file mode 100644
index 0000000..9ccc1a6
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-lantiq.h
@@ -0,0 +1,190 @@
+/*
+ * linux/drivers/pinctrl/pinctrl-lantiq.h
+ * based on linux/drivers/pinctrl/pinctrl-pxa3xx.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * publishhed by the Free Software Foundation.
+ *
+ * Copyright (C) 2012 John Crispin <blogic at openwrt.org>
+ */
+
+#ifndef __PINCTRL_LANTIQ_H
+
+#include <linux/clkdev.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/machine.h>
+
+#include "core.h"
+
+#define ARRAY_AND_SIZE(x) (x), ARRAY_SIZE(x)
+
+#define LTQ_MAX_MUX 4
+#define MFPR_FUNC_MASK 0x3
+
+#define LTQ_PINCONF_PACK(param, arg) ((param) << 16 | (arg))
+#define LTQ_PINCONF_UNPACK_PARAM(conf) ((conf) >> 16)
+#define LTQ_PINCONF_UNPACK_ARG(conf) ((conf) & 0xffff)
+
+enum ltq_pinconf_param {
+ LTQ_PINCONF_PARAM_PULL,
+ LTQ_PINCONF_PARAM_OPEN_DRAIN,
+ LTQ_PINCONF_PARAM_DRIVE_CURRENT,
+ LTQ_PINCONF_PARAM_SLEW_RATE,
+};
+
+struct ltq_cfg_param {
+ const char *property;
+ enum ltq_pinconf_param param;
+};
+
+struct ltq_mfp_pin {
+ const char *name;
+ const unsigned int pin;
+ const unsigned short func[LTQ_MAX_MUX];
+};
+
+struct ltq_pin_group {
+ const char *name;
+ const unsigned mux;
+ const unsigned *pins;
+ const unsigned npins;
+};
+
+struct ltq_pmx_func {
+ const char *name;
+ const char * const *groups;
+ const unsigned num_groups;
+};
+
+struct ltq_pinmux_info {
+ struct device *dev;
+ struct pinctrl_dev *pctrl;
+
+ /* we need to manage up to 5 pad controllers */
+ void __iomem *membase[5];
+
+ /* the descriptor for the subsystem */
+ struct pinctrl_desc *desc;
+
+ /* we expose our pads to the subsystem */
+ struct pinctrl_pin_desc *pads;
+
+ /* the number of pads. this varies between socs */
+ unsigned int num_pads;
+
+ /* these are our multifunction pins */
+ const struct ltq_mfp_pin *mfp;
+ unsigned int num_mfp;
+
+ /* a number of multifunction pins can be grouped together */
+ const struct ltq_pin_group *grps;
+ unsigned int num_grps;
+
+ /* a mapping between function string and id */
+ const struct ltq_pmx_func *funcs;
+ unsigned int num_funcs;
+
+ /* the pinconf options that we are able to read from the DT */
+ const struct ltq_cfg_param *params;
+ unsigned int num_params;
+
+ /* we need 5 clocks max */
+ struct clk *clk[5];
+
+ /* soc specific callback used to apply muxing */
+ int (*apply_mux)(struct pinctrl_dev *pctrldev, int pin, int mux);
+};
+
+enum ltq_pin {
+ GPIO0 = 0,
+ GPIO1,
+ GPIO2,
+ GPIO3,
+ GPIO4,
+ GPIO5,
+ GPIO6,
+ GPIO7,
+ GPIO8,
+ GPIO9,
+ GPIO10, /* 10 */
+ GPIO11,
+ GPIO12,
+ GPIO13,
+ GPIO14,
+ GPIO15,
+ GPIO16,
+ GPIO17,
+ GPIO18,
+ GPIO19,
+ GPIO20, /* 20 */
+ GPIO21,
+ GPIO22,
+ GPIO23,
+ GPIO24,
+ GPIO25,
+ GPIO26,
+ GPIO27,
+ GPIO28,
+ GPIO29,
+ GPIO30, /* 30 */
+ GPIO31,
+ GPIO32,
+ GPIO33,
+ GPIO34,
+ GPIO35,
+ GPIO36,
+ GPIO37,
+ GPIO38,
+ GPIO39,
+ GPIO40, /* 40 */
+ GPIO41,
+ GPIO42,
+ GPIO43,
+ GPIO44,
+ GPIO45,
+ GPIO46,
+ GPIO47,
+ GPIO48,
+ GPIO49,
+ GPIO50, /* 50 */
+ GPIO51,
+ GPIO52,
+ GPIO53,
+ GPIO54,
+ GPIO55,
+
+ GPIO64,
+ GPIO65,
+ GPIO66,
+ GPIO67,
+ GPIO68,
+ GPIO69,
+ GPIO70,
+ GPIO71,
+ GPIO72,
+ GPIO73,
+ GPIO74,
+ GPIO75,
+ GPIO76,
+ GPIO77,
+ GPIO78,
+ GPIO79,
+ GPIO80,
+ GPIO81,
+ GPIO82,
+ GPIO83,
+ GPIO84,
+ GPIO85,
+ GPIO86,
+ GPIO87,
+ GPIO88,
+};
+
+extern int ltq_pinctrl_register(struct platform_device *pdev,
+ struct ltq_pinmux_info *info);
+extern int ltq_pinctrl_unregister(struct platform_device *pdev);
+#endif /* __PINCTRL_PXA3XX_H */
diff --git a/drivers/pinctrl/pinctrl-xway.c b/drivers/pinctrl/pinctrl-xway.c
new file mode 100644
index 0000000..bd0910a9
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-xway.c
@@ -0,0 +1,652 @@
+/*
+ * linux/drivers/pinctrl/pinmux-xway.c
+ * based on linux/drivers/pinctrl/pinmux-pxa910.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * publishhed by the Free Software Foundation.
+ *
+ * Copyright (C) 2012 John Crispin <blogic at openwrt.org>
+ */
+
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/of_gpio.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+
+#include "pinctrl-lantiq.h"
+
+#include <lantiq_soc.h>
+
+/* we have 3 1/2 banks of 16 bit each */
+#define PINS 16
+#define PORT3 3
+#define PORT(x) (x / PINS)
+#define PORT_PIN(x) (x % PINS)
+
+/* we have 2 mux bits that can be set for each pin */
+#define MUX_ALT0 0x1
+#define MUX_ALT1 0x2
+
+/*
+ * each bank has this offset apart from the 1/2 bank that is mixed into the
+ * other 3 ranges
+ */
+#define REG_OFF 0x30
+
+/* these are the offsets to our registers */
+#define GPIO_BASE(p) (REG_OFF * PORT(p))
+#define GPIO_OUT(p) GPIO_BASE(p)
+#define GPIO_IN(p) (GPIO_BASE(p) + 0x04)
+#define GPIO_DIR(p) (GPIO_BASE(p) + 0x08)
+#define GPIO_ALT0(p) (GPIO_BASE(p) + 0x0C)
+#define GPIO_ALT1(p) (GPIO_BASE(p) + 0x10)
+#define GPIO_OD(p) (GPIO_BASE(p) + 0x14)
+#define GPIO_PUDSEL(p) (GPIO_BASE(p) + 0x1c)
+#define GPIO_PUDEN(p) (GPIO_BASE(p) + 0x20)
+
+/* the 1/2 port needs special offsets for some registers */
+#define GPIO3_OD (GPIO_BASE(0) + 0x24)
+#define GPIO3_PUDSEL (GPIO_BASE(0) + 0x28)
+#define GPIO3_PUDEN (GPIO_BASE(0) + 0x2C)
+#define GPIO3_ALT1 (GPIO_BASE(PINS) + 0x24)
+
+/* macros to help us access the registers */
+#define gpio_getbit(m, r, p) (!!(ltq_r32(m + r) & BIT(p)))
+#define gpio_setbit(m, r, p) ltq_w32_mask(0, BIT(p), m + r)
+#define gpio_clearbit(m, r, p) ltq_w32_mask(BIT(p), 0, m + r)
+
+#define MFP_XWAY(a, f0, f1, f2, f3) \
+ { \
+ .name = #a, \
+ .pin = a, \
+ .func = { \
+ XWAY_MUX_##f0, \
+ XWAY_MUX_##f1, \
+ XWAY_MUX_##f2, \
+ XWAY_MUX_##f3, \
+ }, \
+ }
+
+#define GRP_MUX(a, m, p) \
+ { .name = a, .mux = XWAY_MUX_##m, .pins = p, .npins = ARRAY_SIZE(p), }
+
+#define FUNC_MUX(f, m) \
+ { .func = f, .mux = XWAY_MUX_##m, }
+
+#define XWAY_MAX_PIN 32
+#define XR9_MAX_PIN 56
+
+enum xway_mux {
+ XWAY_MUX_GPIO = 0,
+ XWAY_MUX_SPI,
+ XWAY_MUX_ASC,
+ XWAY_MUX_PCI,
+ XWAY_MUX_CGU,
+ XWAY_MUX_EBU,
+ XWAY_MUX_JTAG,
+ XWAY_MUX_EXIN,
+ XWAY_MUX_TDM,
+ XWAY_MUX_STP,
+ XWAY_MUX_SIN,
+ XWAY_MUX_GPT,
+ XWAY_MUX_NMI,
+ XWAY_MUX_NONE = 0xffff,
+};
+
+static const struct ltq_mfp_pin xway_mfp[] = {
+ /* pin f0 f1 f2 f3 */
+ MFP_XWAY(GPIO0, GPIO, EXIN, NONE, TDM),
+ MFP_XWAY(GPIO1, GPIO, EXIN, NONE, NONE),
+ MFP_XWAY(GPIO2, GPIO, CGU, EXIN, NONE),
+ MFP_XWAY(GPIO3, GPIO, CGU, NONE, PCI),
+ MFP_XWAY(GPIO4, GPIO, STP, NONE, ASC),
+ MFP_XWAY(GPIO5, GPIO, STP, NONE, NONE),
+ MFP_XWAY(GPIO6, GPIO, STP, GPT, ASC),
+ MFP_XWAY(GPIO7, GPIO, CGU, PCI, NONE),
+ MFP_XWAY(GPIO8, GPIO, CGU, NMI, NONE),
+ MFP_XWAY(GPIO9, GPIO, ASC, SPI, NONE),
+ MFP_XWAY(GPIO10, GPIO, ASC, SPI, NONE),
+ MFP_XWAY(GPIO11, GPIO, ASC, PCI, SPI),
+ MFP_XWAY(GPIO12, GPIO, ASC, NONE, NONE),
+ MFP_XWAY(GPIO13, GPIO, EBU, SPI, NONE),
+ MFP_XWAY(GPIO14, GPIO, CGU, PCI, NONE),
+ MFP_XWAY(GPIO15, GPIO, SPI, JTAG, NONE),
+ MFP_XWAY(GPIO16, GPIO, SPI, NONE, JTAG),
+ MFP_XWAY(GPIO17, GPIO, SPI, NONE, JTAG),
+ MFP_XWAY(GPIO18, GPIO, SPI, NONE, JTAG),
+ MFP_XWAY(GPIO19, GPIO, PCI, NONE, NONE),
+ MFP_XWAY(GPIO20, GPIO, JTAG, NONE, NONE),
+ MFP_XWAY(GPIO21, GPIO, PCI, EBU, GPT),
+ MFP_XWAY(GPIO22, GPIO, SPI, NONE, NONE),
+ MFP_XWAY(GPIO23, GPIO, EBU, PCI, STP),
+ MFP_XWAY(GPIO24, GPIO, EBU, TDM, PCI),
+ MFP_XWAY(GPIO25, GPIO, TDM, NONE, ASC),
+ MFP_XWAY(GPIO26, GPIO, EBU, NONE, TDM),
+ MFP_XWAY(GPIO27, GPIO, TDM, NONE, ASC),
+ MFP_XWAY(GPIO28, GPIO, GPT, NONE, NONE),
+ MFP_XWAY(GPIO29, GPIO, PCI, NONE, NONE),
+ MFP_XWAY(GPIO30, GPIO, PCI, NONE, NONE),
+ MFP_XWAY(GPIO31, GPIO, EBU, PCI, NONE),
+ MFP_XWAY(GPIO32, GPIO, NONE, NONE, EBU),
+ MFP_XWAY(GPIO33, GPIO, NONE, NONE, EBU),
+ MFP_XWAY(GPIO34, GPIO, NONE, NONE, EBU),
+ MFP_XWAY(GPIO35, GPIO, NONE, NONE, EBU),
+ MFP_XWAY(GPIO36, GPIO, SIN, NONE, EBU),
+ MFP_XWAY(GPIO37, GPIO, PCI, NONE, NONE),
+ MFP_XWAY(GPIO38, GPIO, PCI, NONE, NONE),
+ MFP_XWAY(GPIO39, GPIO, EXIN, NONE, NONE),
+ MFP_XWAY(GPIO40, GPIO, NONE, NONE, NONE),
+ MFP_XWAY(GPIO41, GPIO, NONE, NONE, NONE),
+ MFP_XWAY(GPIO42, GPIO, NONE, NONE, NONE),
+ MFP_XWAY(GPIO43, GPIO, NONE, NONE, NONE),
+ MFP_XWAY(GPIO44, GPIO, NONE, NONE, SIN),
+ MFP_XWAY(GPIO45, GPIO, NONE, NONE, SIN),
+ MFP_XWAY(GPIO46, GPIO, NONE, NONE, EXIN),
+ MFP_XWAY(GPIO47, GPIO, NONE, NONE, SIN),
+ MFP_XWAY(GPIO48, GPIO, EBU, NONE, NONE),
+ MFP_XWAY(GPIO49, GPIO, EBU, NONE, NONE),
+ MFP_XWAY(GPIO50, GPIO, NONE, NONE, NONE),
+ MFP_XWAY(GPIO51, GPIO, NONE, NONE, NONE),
+ MFP_XWAY(GPIO52, GPIO, NONE, NONE, NONE),
+ MFP_XWAY(GPIO53, GPIO, NONE, NONE, NONE),
+ MFP_XWAY(GPIO54, GPIO, NONE, NONE, NONE),
+ MFP_XWAY(GPIO55, GPIO, NONE, NONE, NONE),
+};
+
+static const unsigned pins_jtag[] = {GPIO15, GPIO16, GPIO17, GPIO19, GPIO35};
+static const unsigned pins_asc0[] = {GPIO11, GPIO12};
+static const unsigned pins_asc0_cts_rts[] = {GPIO9, GPIO10};
+static const unsigned pins_stp[] = {GPIO4, GPIO5, GPIO6};
+static const unsigned pins_nmi[] = {GPIO8};
+
+static const unsigned pins_ebu_a24[] = {GPIO13};
+static const unsigned pins_ebu_clk[] = {GPIO21};
+static const unsigned pins_ebu_cs1[] = {GPIO23};
+static const unsigned pins_ebu_a23[] = {GPIO24};
+static const unsigned pins_ebu_wait[] = {GPIO26};
+static const unsigned pins_ebu_a25[] = {GPIO31};
+static const unsigned pins_ebu_rdy[] = {GPIO48};
+static const unsigned pins_ebu_rd[] = {GPIO49};
+
+static const unsigned pins_nand_ale[] = {GPIO13};
+static const unsigned pins_nand_cs1[] = {GPIO23};
+static const unsigned pins_nand_cle[] = {GPIO24};
+static const unsigned pins_nand_rdy[] = {GPIO48};
+static const unsigned pins_nand_rd[] = {GPIO49};
+
+static const unsigned pins_exin0[] = {GPIO0};
+static const unsigned pins_exin1[] = {GPIO1};
+static const unsigned pins_exin2[] = {GPIO2};
+static const unsigned pins_exin3[] = {GPIO39};
+static const unsigned pins_exin4[] = {GPIO46};
+
+static const unsigned pins_spi[] = {GPIO16, GPIO17, GPIO18};
+static const unsigned pins_spi_cs1[] = {GPIO15};
+static const unsigned pins_spi_cs2[] = {GPIO21};
+static const unsigned pins_spi_cs3[] = {GPIO13};
+static const unsigned pins_spi_cs4[] = {GPIO10};
+static const unsigned pins_spi_cs5[] = {GPIO9};
+static const unsigned pins_spi_cs6[] = {GPIO11};
+
+static const unsigned pins_gpt1[] = {GPIO28};
+static const unsigned pins_gpt2[] = {GPIO21};
+static const unsigned pins_gpt3[] = {GPIO6};
+
+static const unsigned pins_clkout0[] = {GPIO8};
+static const unsigned pins_clkout1[] = {GPIO7};
+static const unsigned pins_clkout2[] = {GPIO3};
+static const unsigned pins_clkout3[] = {GPIO2};
+
+static const unsigned pins_pci_gnt1[] = {GPIO30};
+static const unsigned pins_pci_gnt2[] = {GPIO23};
+static const unsigned pins_pci_gnt3[] = {GPIO19};
+static const unsigned pins_pci_gnt4[] = {GPIO38};
+static const unsigned pins_pci_req1[] = {GPIO29};
+static const unsigned pins_pci_req2[] = {GPIO31};
+static const unsigned pins_pci_req3[] = {GPIO3};
+static const unsigned pins_pci_req4[] = {GPIO37};
+
+static const struct ltq_pin_group xway_grps[] = {
+ GRP_MUX("exin0", EXIN, pins_exin0),
+ GRP_MUX("exin1", EXIN, pins_exin1),
+ GRP_MUX("exin2", EXIN, pins_exin2),
+ GRP_MUX("jtag", JTAG, pins_jtag),
+ GRP_MUX("ebu a23", EBU, pins_ebu_a23),
+ GRP_MUX("ebu a24", EBU, pins_ebu_a24),
+ GRP_MUX("ebu a25", EBU, pins_ebu_a25),
+ GRP_MUX("ebu clk", EBU, pins_ebu_clk),
+ GRP_MUX("ebu cs1", EBU, pins_ebu_cs1),
+ GRP_MUX("ebu wait", EBU, pins_ebu_wait),
+ GRP_MUX("nand ale", EBU, pins_nand_ale),
+ GRP_MUX("nand cs1", EBU, pins_nand_cs1),
+ GRP_MUX("nand cle", EBU, pins_nand_cle),
+ GRP_MUX("spi", SPI, pins_spi),
+ GRP_MUX("spi_cs1", SPI, pins_spi_cs1),
+ GRP_MUX("spi_cs2", SPI, pins_spi_cs2),
+ GRP_MUX("spi_cs3", SPI, pins_spi_cs3),
+ GRP_MUX("spi_cs4", SPI, pins_spi_cs4),
+ GRP_MUX("spi_cs5", SPI, pins_spi_cs5),
+ GRP_MUX("spi_cs6", SPI, pins_spi_cs6),
+ GRP_MUX("asc0", ASC, pins_asc0),
+ GRP_MUX("asc0 cts rts", ASC, pins_asc0_cts_rts),
+ GRP_MUX("stp", STP, pins_stp),
+ GRP_MUX("nmi", NMI, pins_nmi),
+ GRP_MUX("gpt1", GPT, pins_gpt1),
+ GRP_MUX("gpt2", GPT, pins_gpt2),
+ GRP_MUX("gpt3", GPT, pins_gpt3),
+ GRP_MUX("clkout0", CGU, pins_clkout0),
+ GRP_MUX("clkout1", CGU, pins_clkout1),
+ GRP_MUX("clkout2", CGU, pins_clkout2),
+ GRP_MUX("clkout3", CGU, pins_clkout3),
+ GRP_MUX("gnt1", PCI, pins_pci_gnt1),
+ GRP_MUX("gnt2", PCI, pins_pci_gnt2),
+ GRP_MUX("gnt3", PCI, pins_pci_gnt3),
+ GRP_MUX("req1", PCI, pins_pci_req1),
+ GRP_MUX("req2", PCI, pins_pci_req2),
+ GRP_MUX("req3", PCI, pins_pci_req3),
+/* xrx only */
+ GRP_MUX("nand rdy", EBU, pins_nand_rdy),
+ GRP_MUX("nand rd", EBU, pins_nand_rd),
+ GRP_MUX("exin3", EXIN, pins_exin3),
+ GRP_MUX("exin4", EXIN, pins_exin4),
+ GRP_MUX("gnt4", PCI, pins_pci_gnt4),
+ GRP_MUX("req4", PCI, pins_pci_gnt4),
+};
+
+static const char * const xway_pci_grps[] = {"gnt1", "gnt2",
+ "gnt3", "req1",
+ "req2", "req3"};
+static const char * const xway_spi_grps[] = {"spi", "spi_cs1",
+ "spi_cs2", "spi_cs3",
+ "spi_cs4", "spi_cs5",
+ "spi_cs6"};
+static const char * const xway_cgu_grps[] = {"clkout0", "clkout1",
+ "clkout2", "clkout3"};
+static const char * const xway_ebu_grps[] = {"ebu a23", "ebu a24",
+ "ebu a25", "ebu cs1",
+ "ebu wait", "ebu clk",
+ "nand ale", "nand cs1",
+ "nand cle"};
+static const char * const xway_exin_grps[] = {"exin0", "exin1", "exin2"};
+static const char * const xway_gpt_grps[] = {"gpt1", "gpt2", "gpt3"};
+static const char * const xway_asc_grps[] = {"asc0", "asc0 cts rts"};
+static const char * const xway_jtag_grps[] = {"jtag"};
+static const char * const xway_stp_grps[] = {"stp"};
+static const char * const xway_nmi_grps[] = {"nmi"};
+
+/* ar9/vr9/gr9 */
+static const char * const xrx_ebu_grps[] = {"ebu a23", "ebu a24",
+ "ebu a25", "ebu cs1",
+ "ebu wait", "ebu clk",
+ "nand ale", "nand cs1",
+ "nand cle", "nand rdy",
+ "nand rd"};
+static const char * const xrx_exin_grps[] = {"exin0", "exin1", "exin2",
+ "exin3", "exin4"};
+static const char * const xrx_pci_grps[] = {"gnt1", "gnt2",
+ "gnt3", "gnt4",
+ "req1", "req2",
+ "req3", "req4"};
+
+static const struct ltq_pmx_func danube_funcs[] = {
+ {"spi", ARRAY_AND_SIZE(xway_spi_grps)},
+ {"asc", ARRAY_AND_SIZE(xway_asc_grps)},
+ {"cgu", ARRAY_AND_SIZE(xway_cgu_grps)},
+ {"jtag", ARRAY_AND_SIZE(xway_jtag_grps)},
+ {"exin", ARRAY_AND_SIZE(xway_exin_grps)},
+ {"stp", ARRAY_AND_SIZE(xway_stp_grps)},
+ {"gpt", ARRAY_AND_SIZE(xway_gpt_grps)},
+ {"nmi", ARRAY_AND_SIZE(xway_nmi_grps)},
+ {"pci", ARRAY_AND_SIZE(xway_pci_grps)},
+ {"ebu", ARRAY_AND_SIZE(xway_ebu_grps)},
+};
+
+static const struct ltq_pmx_func xrx_funcs[] = {
+ {"spi", ARRAY_AND_SIZE(xway_spi_grps)},
+ {"asc", ARRAY_AND_SIZE(xway_asc_grps)},
+ {"cgu", ARRAY_AND_SIZE(xway_cgu_grps)},
+ {"jtag", ARRAY_AND_SIZE(xway_jtag_grps)},
+ {"exin", ARRAY_AND_SIZE(xrx_exin_grps)},
+ {"stp", ARRAY_AND_SIZE(xway_stp_grps)},
+ {"gpt", ARRAY_AND_SIZE(xway_gpt_grps)},
+ {"nmi", ARRAY_AND_SIZE(xway_nmi_grps)},
+ {"pci", ARRAY_AND_SIZE(xrx_pci_grps)},
+ {"ebu", ARRAY_AND_SIZE(xrx_ebu_grps)},
+};
+
+/* --------- pinconf related code --------- */
+static int xway_pinconf_get(struct pinctrl_dev *pctldev,
+ unsigned pin,
+ unsigned long *config)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctldev);
+ enum ltq_pinconf_param param = LTQ_PINCONF_UNPACK_PARAM(*config);
+ int port = PORT(pin);
+ u32 reg;
+
+ switch (param) {
+ case LTQ_PINCONF_PARAM_OPEN_DRAIN:
+ if (port == PORT3)
+ reg = GPIO3_OD;
+ else
+ reg = GPIO_OD(port);
+ *config = LTQ_PINCONF_PACK(param,
+ !!gpio_getbit(info->membase[0], reg, PORT_PIN(port)));
+ break;
+
+ case LTQ_PINCONF_PARAM_PULL:
+ if (port == PORT3)
+ reg = GPIO3_PUDEN;
+ else
+ reg = GPIO_PUDEN(port);
+ if (!gpio_getbit(info->membase[0], reg, PORT_PIN(port))) {
+ *config = LTQ_PINCONF_PACK(param, 0);
+ break;
+ }
+
+ if (port == PORT3)
+ reg = GPIO3_PUDSEL;
+ else
+ reg = GPIO_PUDSEL(port);
+ if (!gpio_getbit(info->membase[0], reg, PORT_PIN(port)))
+ *config = LTQ_PINCONF_PACK(param, 2);
+ else
+ *config = LTQ_PINCONF_PACK(param, 1);
+ break;
+
+ default:
+ dev_err(pctldev->dev, "Invalid config param %04x\n", param);
+ return -ENOTSUPP;
+ }
+ return 0;
+}
+
+static int xway_pinconf_set(struct pinctrl_dev *pctldev,
+ unsigned pin,
+ unsigned long config)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctldev);
+ enum ltq_pinconf_param param = LTQ_PINCONF_UNPACK_PARAM(config);
+ int arg = LTQ_PINCONF_UNPACK_ARG(config);
+ int port = PORT(pin);
+ u32 reg;
+
+ switch (param) {
+ case LTQ_PINCONF_PARAM_OPEN_DRAIN:
+ if (port == PORT3)
+ reg = GPIO3_OD;
+ else
+ reg = GPIO_OD(port);
+ gpio_setbit(info->membase[0], reg, PORT_PIN(port));
+ break;
+
+ case LTQ_PINCONF_PARAM_PULL:
+ if (port == PORT3)
+ reg = GPIO3_PUDEN;
+ else
+ reg = GPIO_PUDEN(port);
+ if (arg == 0) {
+ gpio_clearbit(info->membase[0], reg, PORT_PIN(port));
+ break;
+ }
+ gpio_setbit(info->membase[0], reg, PORT_PIN(port));
+
+ if (port == PORT3)
+ reg = GPIO3_PUDSEL;
+ else
+ reg = GPIO_PUDSEL(port);
+ if (arg == 1)
+ gpio_clearbit(info->membase[0], reg, PORT_PIN(port));
+ else if (arg == 2)
+ gpio_setbit(info->membase[0], reg, PORT_PIN(port));
+ else
+ dev_err(pctldev->dev, "Invalid pull value %d\n", arg);
+ break;
+
+ default:
+ dev_err(pctldev->dev, "Invalid config param %04x\n", param);
+ return -ENOTSUPP;
+ }
+ return 0;
+}
+
+struct pinconf_ops xway_pinconf_ops = {
+ .pin_config_get = xway_pinconf_get,
+ .pin_config_set = xway_pinconf_set,
+};
+
+static struct pinctrl_desc xway_pctrl_desc = {
+ .owner = THIS_MODULE,
+ .confops = &xway_pinconf_ops,
+};
+
+static inline int xway_mux_apply(struct pinctrl_dev *pctrldev,
+ int pin, int mux)
+{
+ struct ltq_pinmux_info *info = pinctrl_dev_get_drvdata(pctrldev);
+ int port = PORT(pin);
+ u32 alt1_reg = GPIO_ALT1(pin);
+
+ if (port == PORT3)
+ alt1_reg = GPIO3_ALT1;
+
+ if (mux & MUX_ALT0)
+ gpio_setbit(info->membase[0], GPIO_ALT0(pin), PORT_PIN(pin));
+ else
+ gpio_clearbit(info->membase[0], GPIO_ALT0(pin), PORT_PIN(pin));
+
+ if (mux & MUX_ALT1)
+ gpio_setbit(info->membase[0], alt1_reg, PORT_PIN(pin));
+ else
+ gpio_clearbit(info->membase[0], alt1_reg, PORT_PIN(pin));
+
+ return 0;
+}
+
+static const struct ltq_cfg_param xway_cfg_params[] = {
+ {"lantiq,pull", LTQ_PINCONF_PARAM_PULL},
+ {"lantiq,open-drain", LTQ_PINCONF_PARAM_OPEN_DRAIN},
+};
+
+static struct ltq_pinmux_info xway_info = {
+ .mfp = xway_mfp,
+ .desc = &xway_pctrl_desc,
+ .apply_mux = xway_mux_apply,
+ .params = xway_cfg_params,
+ .num_params = ARRAY_SIZE(xway_cfg_params),
+};
+
+/* --------- gpio_chip related code --------- */
+static void xway_gpio_set(struct gpio_chip *chip, unsigned int pin, int val)
+{
+ struct ltq_pinmux_info *info = dev_get_drvdata(chip->dev);
+
+ if (val)
+ gpio_setbit(info->membase[0], GPIO_OUT(pin), PORT_PIN(pin));
+ else
+ gpio_clearbit(info->membase[0], GPIO_OUT(pin), PORT_PIN(pin));
+}
+
+static int xway_gpio_get(struct gpio_chip *chip, unsigned int pin)
+{
+ struct ltq_pinmux_info *info = dev_get_drvdata(chip->dev);
+
+ return gpio_getbit(info->membase[0], GPIO_IN(pin), PORT_PIN(pin));
+}
+
+static int xway_gpio_dir_in(struct gpio_chip *chip, unsigned int pin)
+{
+ struct ltq_pinmux_info *info = dev_get_drvdata(chip->dev);
+
+ gpio_clearbit(info->membase[0], GPIO_DIR(pin), PORT_PIN(pin));
+
+ return 0;
+}
+
+static int xway_gpio_dir_out(struct gpio_chip *chip, unsigned int pin, int val)
+{
+ struct ltq_pinmux_info *info = dev_get_drvdata(chip->dev);
+
+ gpio_setbit(info->membase[0], GPIO_DIR(pin), PORT_PIN(pin));
+ xway_gpio_set(chip, pin, val);
+
+ return 0;
+}
+
+static int xway_gpio_req(struct gpio_chip *chip, unsigned offset)
+{
+ int gpio = chip->base + offset;
+
+ return pinctrl_request_gpio(gpio);
+}
+
+static void xway_gpio_free(struct gpio_chip *chip, unsigned offset)
+{
+ int gpio = chip->base + offset;
+
+ pinctrl_free_gpio(gpio);
+}
+
+static struct gpio_chip xway_chip = {
+ .label = "gpio-xway",
+ .direction_input = xway_gpio_dir_in,
+ .direction_output = xway_gpio_dir_out,
+ .get = xway_gpio_get,
+ .set = xway_gpio_set,
+ .request = xway_gpio_req,
+ .free = xway_gpio_free,
+ .base = -1,
+};
+
+/* --------- register the pinctrl layer --------- */
+static struct pinctrl_xway_soc {
+ int pin_count;
+ const struct ltq_pmx_func *funcs;
+ unsigned int num_funcs;
+} soc_cfg[] = {
+ /* legacy xway */
+ {XWAY_MAX_PIN, danube_funcs, ARRAY_SIZE(danube_funcs)},
+ /* xway xr9 series */
+ {XR9_MAX_PIN, xrx_funcs, ARRAY_SIZE(xrx_funcs)},
+};
+
+static struct pinctrl_gpio_range xway_gpio_range = {
+ .name = "XWAY GPIO",
+ .gc = &xway_chip,
+};
+
+static const struct of_device_id xway_match[] = {
+ { .compatible = "lantiq,pinctrl-xway", .data = &soc_cfg[0]},
+ { .compatible = "lantiq,pinctrl-xr9", .data = &soc_cfg[1]},
+ {},
+};
+MODULE_DEVICE_TABLE(of, xway_match);
+
+static int __devinit pinmux_xway_probe(struct platform_device *pdev)
+{
+ const struct of_device_id *match;
+ const struct pinctrl_xway_soc *xway_soc;
+ struct resource *res;
+ int ret, i;
+
+ /* get and remap our register range */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "Failed to get resource\n");
+ return -ENOENT;
+ }
+ xway_info.membase[0] = devm_request_and_ioremap(&pdev->dev, res);
+ if (!xway_info.membase[0]) {
+ dev_err(&pdev->dev, "Failed to remap resource\n");
+ return -ENOMEM;
+ }
+
+ match = of_match_device(xway_match, &pdev->dev);
+ if (match)
+ xway_soc = (const struct pinctrl_xway_soc*) match->data;
+ else
+ xway_soc = &soc_cfg[0];
+
+ /* find out how many pads we have */
+ xway_chip.ngpio = xway_soc->pin_count;
+
+ /* load our pad descriptors */
+ xway_info.pads = devm_kzalloc(&pdev->dev,
+ sizeof(struct pinctrl_pin_desc) * xway_chip.ngpio,
+ GFP_KERNEL);
+ if (!xway_info.pads) {
+ dev_err(&pdev->dev, "Failed to allocate pads\n");
+ return -ENOMEM;
+ }
+ for (i = 0; i < xway_chip.ngpio; i++) {
+ /* strlen("ioXY") + 1 = 5 */
+ char *name = devm_kzalloc(&pdev->dev, 5, GFP_KERNEL);
+
+ if (!name) {
+ dev_err(&pdev->dev, "Failed to allocate pad name\n");
+ return -ENOMEM;
+ }
+ snprintf(name, 5, "io%d", i);
+ xway_info.pads[i].number = GPIO0 + i;
+ xway_info.pads[i].name = name;
+ }
+ xway_pctrl_desc.pins = xway_info.pads;
+
+ /* load the gpio chip */
+ xway_chip.dev = &pdev->dev;
+ of_gpiochip_add(&xway_chip);
+ ret = gpiochip_add(&xway_chip);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to register gpio chip\n");
+ return ret;
+ }
+
+ /* setup the data needed by pinctrl */
+ xway_pctrl_desc.name = dev_name(&pdev->dev);
+ xway_pctrl_desc.npins = xway_chip.ngpio;
+
+ xway_info.num_pads = xway_chip.ngpio;
+ xway_info.num_mfp = xway_chip.ngpio;
+ xway_info.grps = xway_grps;
+ xway_info.num_grps = ARRAY_SIZE(xway_grps);
+ xway_info.funcs = xway_soc->funcs;
+ xway_info.num_funcs = xway_soc->num_funcs;
+
+ /* register with the generic lantiq layer */
+ ret = ltq_pinctrl_register(pdev, &xway_info);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to register pinctrl driver\n");
+ return ret;
+ }
+
+ /* finish with registering the gpio range in pinctrl */
+ xway_gpio_range.npins = xway_chip.ngpio;
+ xway_gpio_range.base = xway_chip.base;
+ pinctrl_add_gpio_range(xway_info.pctrl, &xway_gpio_range);
+ dev_info(&pdev->dev, "Init done\n");
+ return 0;
+}
+
+static struct platform_driver pinmux_xway_driver = {
+ .probe = pinmux_xway_probe,
+ .driver = {
+ .name = "pinctrl-xway",
+ .owner = THIS_MODULE,
+ .of_match_table = xway_match,
+ },
+};
+
+static int __init pinmux_xway_init(void)
+{
+ return platform_driver_register(&pinmux_xway_driver);
+}
+
+arch_initcall(pinmux_xway_init);
--
1.7.9.1
More information about the devicetree-discuss
mailing list