[PATCH] stmmac: Add device-tree support

[Giuseppe CAVALLARO]

On 3/12/2012 5:23 PM, Stefan Roese wrote:
> On Monday 12 March 2012 16:30:37 Giuseppe CAVALLARO wrote:
>>>>> +Required properties:
>>>>> +- compatible: Should be "stm,gmac"
>>>>
>>>> This is too generic. This should be 1 string per version of h/w.
>>>
>>> Viresh, Giuseppe, can you please suggest a proper string for the SPEAr600
>>> STMMAC core, including version?
>>>
>>>> 'stm' should be 'st' according to vendor-prefixes.txt.
>>
>> I'm not familiar with devicetree; maybe we should have:
>>
>> "stmicro,mac100"
>> "stmicro,gmac"
>>
>> or: st instead of stmicro if you prefer.
>>
>> in fact, stmmac is for mac100 and gmac devices.
> 
> How about "st,spear600-gmac" for SPEAr600 then?

IIUC, as final result we should have something like this... that sounds
quite good to me.

ST/ARM SPEAr
"st,spear600-gmac"
"st,spear1310-gmac"
  ...

ST/SH

"st,stx7108-gmac"
"st,stx7106-gmac"
"st,stx7109-mac"    ->>> mac10/100
...

MIPS
"st,Loongson1B"

>  
>>> Okay.
>>>
>>>>> +- reg: Address and length of the register set for the device
>>>>> +- interrupt-parent: Should be the phandle for the interrupt controller
>>>>> +  that services interrupts for this device
>>>>> +- interrupts: Should contain the STMMAC interrupts
>>>>> +- interrupt-names: Should contain the interrupt names "macirq"
>>>>> +  "eth_wake_irq" if this interrupt is supported in the "interrupts"
>>>>> +  property
>>>>
>>>> You should be able to tell this from the compatible string and number of
>>>> interrupts.
>>>
>>> Yes. Currently the driver uses platform_get_irq_byname() to register the
>>> irq's. That's why I added these properties. Is there something wrong with
>>> using it this way?
>>>
>>>>> +- phy-mode: String, operation mode of the PHY interface.
>>>>> +  Supported values are: "mii", "rmii", "gmii", "rgmii".
>>>>> +- phy-addr: MDIO address of the PHY
>>>>
>>>> This is normally probed or the mdio bus is a sub-node of the MAC node.
>>>> See arch/powerpc/boot/dts/mpc8377_mds.dts for an example.
>>>
>>> Okay, I'll rework this.
>>>
>>>>> +
>>>>> +Optional properties:
>>>>> +- stm,prog-burst-len: Specify the burst length
>>>>> +- stm,has-gmac: Indicates that the controller supports 1000Mbps
>>>>> +- stm,has-pmt: Indicates that the controller supports power management
>>>>
>>>> I think these should all be encoded by the compatible string.
>>
>> and should we have all the other flags e.g. tx_coe etc?
>> (see stmmac.txt)
> 
> As Rob suggested, some of these flags/parameters are implicitly defined by the 
> compatible string. If this is not the case, then sure, those flags/parameters 
> need to be provided via the device-tree as well. I just don't need "tx_coe" 
> etc. for my platform (SPEAr600) as far as I know. I suggest to add support for 
> them once they are really needed/used by other platforms.

Ok, but on SPEAr indeed some of these are not used at all.
If you agree, we can go head with these and then we will add new ones
next time. In the meantime, I will try to be more familiar with
devicetree and provide further patches

peppe

> 
> Thanks,
> Stefan
> --
> To unsubscribe from this list: send the line "unsubscribe netdev" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>