[PATCH] of: Add generic device tree DMA helpers

[Nicolas Ferre]

On 03/16/2012 02:28 PM, Cousson, Benoit :
> On 3/16/2012 1:04 PM, Arnd Bergmann wrote:
>> On Friday 16 March 2012, Cousson, Benoit wrote:
>>> And it seems that other ARM SoCs are using it for the same purpose.
>>> There are at least 230+ IORESOURCE_DMA instances in the kernel today.
>>
>> These tend to be the ones that don't use dmaengine but either the
>> ISA dma api or a platform specific variant of that, right?
>>
>> Also, I think that most of those definitions are for the same few
>> devices. The number that I see is much lower:
>>
>> $ git grep -l IORESOURCE_DMA drivers/ sound/ | wc -l
>>       51
> 
> Gosh, good point... I've just done a dumb grep, but most of them are in
> the device creation inside arch code:-(
> 
> Assuming OMAP driver does contains omap in the name, the result is
> indeed way smaller.
> 
> git grep -l IORESOURCE_DMA drivers/ sound/ | grep omap
> 
> drivers/crypto/omap-aes.c
> drivers/crypto/omap-sham.c
> drivers/spi/spi-omap2-mcspi.c
> drivers/tty/serial/omap-serial.c
> sound/soc/omap/omap-dmic.c
> sound/soc/omap/omap-hdmi.c
> 
> We do have 127 DMA requests and only 6 drivers are using them, that's a
> pity...
> 
>> Out of those, a quite number are mips or blackfin or xtensa based, or are
>> for legacy ISA devices, which leaves 29 drivers for ARM.
>>
>>> For the moment it is still used in a lot of places, and without any
>>> other better API yet, it is still useful. As written it is there only
>>> for simple single DMA controller case.
>>>
>>> By maintaining that IORESOURCE_DMA for the moment we can adapt some
>>> driver to DT without having to change the way they are retrieving
>>> information. By using IORESOURCE_IRQ and IORESOURCE_MEM, we had the same
>>> advantage.
>>
>> The main difference to IORESOURCE_IRQ and IORESOURCE_MEM that I see
>> is that those are going to start for any forseeable time and are actually
>> helpful in a lot of ways. We are not going to remove the single number
>> space for interrupts in the next few years. For DMA, the dmaengine API
>> has already moved away from the flat number space of the ISA API.
>>
>>> Otherwise how are we supposed to get the DMA channel for non-DT boot
>>> until we have migrated everything to DT? A bunch of ARM SoC are using
>>> IORESOURCE_DMA for the same purpose.
>>>
>>> The goal here is really to maintain that during the transition phase
>>> only. As soon as the full DT support is there, we can switch to the
>>> of_ API.
>>>
>>> Ideally, we should define and use a generic API non dependent of DT.
>>> AFAIK, that does not exist so far.
>>> And since most drivers are not using dmaengine, we do not even have a
>>> common DMA fmwk to define an API on top.
>>>
>>> I fully agree that this IORESOURCE_DMA is not scalable for multiple
>>> controller, ugly, and must be avoided like the plague.
>>> But what other options do we have during the transition?
>>
>> We could use the same binding for the nonstandard controllers, but
>> keep the dma channel number lookup separate for those, and let them
>> call of_get_dma_request directly.
>>
>> Since there are not too many drivers using those controllers with
>> dma resources today, it's fairly easy to go through those as we write
>> the driver bindings and just do
>>
>>     err = of_get_dma_request(pdev->dev.of_node, 0,&dma);
>>     if (err) {
>>         struct resource *r = platform_get_resource(pdev,
>> IORESOURCE_DMA, 0);
>>         if (r)
>>             dma = r->start;
>>     }
>>
>> For the drivers that we convert to DT before we convert them to
>> dmaengine,
>> and not do anything if we convert them to dmaengine first.
> 
> Considering the small amount of OMAP drivers really using
> IORESOURCE_DMA, I guess this is fair enough.
> 
> Bottom-line, I do not have any more issue removing this of_dma_to_resource.
> 
> 
> Nico,
> Is that OK for you to repost the patch without this function?

Yes sure, I will repost a V2 soon.

I also try to have an integration in DT selftest.c:
- that will show some possibilities of the API
- that will give some examples of usage (1 or 2 xlate() functions)
- that made me review my code and find a weakness
- that will allow to monitor non-regression (obviously)
=> WIP...

Bye,
-- 
Nicolas Ferre