[PATCH v1 2/5] mmc: mxs-mmc: add dt probe support
Dong Aisheng
aisheng.dong at freescale.com
Wed Mar 14 19:09:40 EST 2012
On Wed, Mar 14, 2012 at 03:23:43PM +0800, Jean-Christophe PLAGNIOL-VILLARD wrote:
> On 16:47 Tue 13 Mar , Dong Aisheng wrote:
> > From: Dong Aisheng <dong.aisheng at linaro.org>
> >
> > Signed-off-by: Dong Aisheng <dong.aisheng at linaro.org>
> >
> > ---
> > The patch is still using a private way for dma part binding
> > since the common dma binding is still under discussion.
> > http://www.spinics.net/lists/linux-omap/msg65528.html
> >
> > Will update to use common dma binding when it hits mainline.
> > ---
> > .../devicetree/bindings/mmc/fsl-mxs-mmc.txt | 23 ++++++
> > drivers/mmc/host/mxs-mmc.c | 82 +++++++++++++++++++-
> > 2 files changed, 102 insertions(+), 3 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/mmc/fsl-mxs-mmc.txt b/Documentation/devicetree/bindings/mmc/fsl-mxs-mmc.txt
> > new file mode 100644
> > index 0000000..adc1142
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/mmc/fsl-mxs-mmc.txt
> > @@ -0,0 +1,23 @@
> > +* FREESCALE MXS MMC peripheral
> > +
> > +Required properties:
> > +- compatible : Should be "fsl,<chip>-mmc"
> > +- reg : Should contain registers location and length
> > +- interrupts : Should contain interrupt.
> > + The format is <irq_err irq_dma>.
> > +- dma_channel: Should contain the dma channel it uses
> > +
> > +Optional properties:
> > +- wp-gpios : Specify GPIOs for write protection
> > +- slot-4bit: Specify 4 bit mode support
> > +- slot-8bit: Specify 8 bit and 4 bit mode support
> > +
> > +Examples:
> > +mmc1: ssp at 80010000 {
> > + compatible = "fsl,imx28-mmc";
> > + reg = <0x80010000 2000>;
> > + /* <irq_err irq_dma> */
> > + interrupts = <96 82>;
> > + dma_channel = <0>;
> > + slot-8bit;
> > +};
> > diff --git a/drivers/mmc/host/mxs-mmc.c b/drivers/mmc/host/mxs-mmc.c
> > index 382c835..6cf2d17 100644
> > --- a/drivers/mmc/host/mxs-mmc.c
> > +++ b/drivers/mmc/host/mxs-mmc.c
> > @@ -38,6 +38,10 @@
> > #include <linux/gpio.h>
> > #include <linux/regulator/consumer.h>
> > #include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/of_gpio.h>
> > +#include <linux/slab.h>
> >
> > #include <mach/mxs.h>
> > #include <mach/common.h>
> > @@ -673,17 +677,79 @@ static bool mxs_mmc_dma_filter(struct dma_chan *chan, void *param)
> > return true;
> > }
> >
> > +#ifdef CONFIG_OF
> > +static struct resource * __devinit mxs_mmc_get_of_dmares(
> > + struct platform_device *pdev)
> > +{
> > + struct device_node *np = pdev->dev.of_node;
> > + struct resource *dmares;
> > + int ret;
> > +
> > + if (!np)
> > + return NULL;
> > +
> > + dmares = kzalloc(sizeof(*dmares), GFP_KERNEL);
> > + dmares->flags = IORESOURCE_DMA;
> > + ret = of_property_read_u32(np, "dma_channel", &dmares->start);
> > + if (ret) {
> > + dev_err(&pdev->dev, "unable to get dmares from dt\n");
> > + return NULL;
> > + }
> > + dmares->end = dmares->start;
> > +
> > + return dmares;
> > +}
> > +
> > +static int __devinit mxs_mmc_get_of_property(struct platform_device *pdev,
> > + struct mxs_mmc_platform_data **ppdata)
> > +{
> > + struct device_node *np = pdev->dev.of_node;
> > + struct mxs_mmc_platform_data *pdata = *ppdata;
> > +
> > + if (!np)
> > + return -ENODEV;
> > +
> > + pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
> > +
> > + if (of_get_property(np, "slot-8bit", NULL))
> > + pdata->flags |= SLOTF_8_BIT_CAPABLE;
> > +
> > + if (of_get_property(np, "slot-4bit", NULL))
> > + pdata->flags |= SLOTF_4_BIT_CAPABLE;
> it will conflit if both binding are set use a number instead
>
Hmm, i did not see conflict, can you explain more?
The "slot-8bit" includes the support for 4bit.(see binding doc)
Even user define them two property in dt by mistake, it does not cause conflict.
See:
if (pdata) {
if (pdata->flags & SLOTF_8_BIT_CAPABLE)
mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA;
if (pdata->flags & SLOTF_4_BIT_CAPABLE)
mmc->caps |= MMC_CAP_4_BIT_DATA;
}
Regards
Dong Aisheng
More information about the devicetree-discuss
mailing list