[PATCH] pinctrl: Add one-register-per-pin type device tree based pinctrl driver

Stephen Warren swarren at wwwdotorg.org
Fri Jun 22 08:13:26 EST 2012


On 06/19/2012 07:56 AM, Tony Lindgren wrote:
> Hi,
> 
> Below is the pinctrl-single patch updated with hopefully all the Stephen's
> comments addressed. The binding still needs to be looked at, see relevant
> parts of the discussion below.
...
> From: Tony Lindgren <tony at atomide.com>
> Date: Wed, 6 Jun 2012 04:18:18 -0700
> Subject: [PATCH] pinctrl: Add one-register-per-pin type device tree based pinctrl driver
> 
> Add one-register-per-pin type device tree based pinctrl driver.
> 
> Currently this driver only works on omap2+ series of processors,
> where there is either an 8 or 16-bit padconf register for each pin.
> Support for other similar pinmux controllers can be added.
> 
> Signed-off-by: Tony Lindgren <tony at atomide.com>
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
> new file mode 100644
> index 0000000..929254c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
> @@ -0,0 +1,106 @@
> +One-register-per-pin type device tree based pinctrl driver
> +
> +Required properties:
> +- compatible : "pinctrl-single"
> +
> +- reg : offset and length of the register set for the mux registers
> +
> +- pinctrl-single,register-width : pinmux register access width in bits
> +
> +- pinctrl-single,function-mask : mask of allowed pinmux function bits
> +  in the pinmux register
> +
> +- pinctrl-single,pinconf-mask : mask of allowed pinconf bits in the
> +  pinmux register; this gets combined with pinconf mask but is a separate
> +  mask to allow the option of setting pinconf separatately from the
> +  function

Given that this binding doesn't allow describing pin configuration at
present, I would simply remove all mention of that property in the
binding documentation. It can be added back if/when that feature is
added. Any future driver using this binding can refuse to allow pin
configuration if that property is missing.

> +- pinctrl-single,function-off : function off mode for disabled state if
> +  available and same for all registers; if not, use a value larger than
> +  function-mask to ignore disabling of registers

Rather than requiring an invalid value in this property, shouldn't the
lack of a valid function-off value be represented by the property not
being present in the DT?

> +This driver assumes that there is only one register for each pin,
> +and uses the common pinctrl bindings as specified in the pinctrl-bindings.txt
> +document in this directory.

At this point in the file, I think you need to mention that you're
switching from describing the top-level device node to describing pin
configuration nodes.

> +The pinctrl register offsets and default values are specified as pairs

I thought we were going to remove "default" here?

> +using pinctrl-single,pins. For example, setting a pin for a device
> +could be done with:
> +
> +	pinctrl-single,pins = <0xdc 0x118>;
> +
> +Where 0xdc is the offset from the pinctrl register base address for the
> +device pinctrl register, and 0x118 contains the desired value of the
> +pinctrl register. See the device example and static board pins example
> +below for more information.

There should be some explanation only the portion of this value covered
by the pinctrl-single,function-mask value is updated in the register.

> +This driver tries to avoid understanding pin and function names because of
> +the extra bloat they would cause especially in the case of a large number
> +of pins. This driver just sets what is specified for the board in the .dts file.
> +Further user space debugging tools can be developed to decipher the pin and
> +function names using debugfs.

There shouldn't be any discussion of a driver here; the binding is a HW
description.

> +Example:

I only reviewed the binding document, not the code.


More information about the devicetree-discuss mailing list